Page 117 of 406
Make sure the shift lever is fully in PARK (P)
before starting the engine. Your vehicle has an
automatic transaxle shift lock control system. You
have to fully apply the regular brakes rst and
then press the shift lever button before shifting
from PARK (P) while the ignition key is in RUN. If
you cannot shift out of PARK (P), ease pressure
on the shift lever and push the shift lever all
the way into PARK (P) while maintaining brake
application. Then press the shift lever button and
move the shift lever into another gear. See
Shifting Out of PARK (P) on page 122.
REVERSE (R):Use this gear to back up.
Notice:Shifting to REVERSE (R) while your
vehicle is moving forward could damage
the transaxle. The repairs would not be
covered by your warranty. Shift to
REVERSE (R) only after your vehicle is
stopped.
To rock your vehicle back and forth to get out of
snow, ice or sand without damaging your
transaxle, seeIf Your Vehicle is Stuck in Sand,
Mud, Ice, or Snow on page 241.NEUTRAL (N):In this position, the engine does
not connect with the wheels. To restart the engine
while your vehicle is already moving, use
NEUTRAL (N) only. Also, use NEUTRAL (N) when
your vehicle is being towed.
{CAUTION:
Shifting into a drive gear while the engine
is running at high speed is dangerous.
Unless your foot is rmly on the brake
pedal, your vehicle could move very
rapidly. You could lose control and hit
people or objects. Do not shift into a drive
gear while your engine is running at high
speed.
Notice:Shifting out of PARK (P) or
NEUTRAL (N) while the engine is running at
high speed may damage the transaxle.
The repairs would not be covered by your
warranty. Be sure the engine is not running at
high speeds when shifting your vehicle.
117
ProCarManuals.com
Page 119 of 406
Parking Brake
To set the parking
brake, push down the
parking brake pedal with
your left foot. If the
ignition is on, the brake
system warning light
will come on. SeeBrake
System Warning Light
on page 168.
To release the parking brake, hold the regular
brake pedal down with your right foot. Push down
momentarily on the parking brake pedal with
your left foot until you feel the pedal release. If the
parking brake is not released when you begin to
drive, the brake system warning light will be
on and a chime will sound warning you that the
parking brake is still on.The PUSH PARK PEDAL message will also
appear in the Driver Information Center (DIC) to
remind you to release the parking brake. SeeDIC
Warnings and Messages on page 182.
Notice:Driving with the parking brake on can
overheat the brake system and cause
premature wear or damage to brake system
parts. Make sure that the parking brake is fully
released and the brake warning light is off
before driving.
Regenerative Braking
Your vehicle has a regenerative braking system.
Regenerative braking takes some of the energy
from the moving vehicle and turns it back
into electrical energy. This energy is then stored
back into the vehicle’s hybrid battery system,
contributing to increased fuel efficiency.
The system works whenever you take your foot off
the accelerator pedal while your vehicle is
moving in a forward gear. This causes your vehicle
to slow down slightly faster. It may feel like the
brake pedal is being pressed, even when it is not.
119
ProCarManuals.com
Page 120 of 406
Shifting Into PARK (P)
{CAUTION:
It can be dangerous to get out of your
vehicle if the shift lever is not fully in
PARK (P) with the parking brake rmly
set. Your vehicle can roll. If you have left
the engine running, the vehicle can move
suddenly. You or others could be injured.
To be sure your vehicle will not move,
even when you are on fairly level ground,
use the steps that follow.1. Hold the brake pedal down with your right foot
and set the parking brake.
2. Move the shift lever into PARK (P) by pressing
the button on the shift lever while pushing the
shift lever all the way toward the front of
the vehicle.
3. Turn the ignition key to OFF.
4. Remove the key and take it with you. If you
can leave your vehicle with the ignition key in
your hand, your vehicle is in PARK (P).
120
ProCarManuals.com
Page 124 of 406
Running the Engine While Parked
It is better not to park with the engine running. But if
you ever have to, here are some things to know.
{CAUTION:
There is something about your vehicle that
can make it move suddenly, and you or
others can be seriously injured. This can
happen if the vehicle is in the Auto Stop
mode, and the shift lever is in DRIVE (D).
Because your vehicle has the Automatic
Engine Start/Stop feature, your vehicle’s
engine might seem to be shut off when you
come to a complete stop. However, if you
then start to exit the vehicle, as soon as
you take your foot off the brake pedal, the
engine will start again and the vehicle can
move forward. If you are going to exit your
vehicle, rst shift to PARK (P) and turn the
ignition to LOCK. Then exit.
{CAUTION:
Idling the engine with the climate control
system off could allow dangerous exhaust
into your vehicle. See the earlier caution
underEngine Exhaust on page 123.
Also, idling in a closed-in place can let
deadly carbon monoxide (CO) into your
vehicle even if the climate control fan is at
the highest setting. One place this can
happen is a garage. Exhaust — with
CO — can come in easily. NEVER park in
a garage with the engine running.
Another closed-in place can be a blizzard.
SeeWinter Driving on page 237.
124
ProCarManuals.com
Page 133 of 406
Sunroof
If your vehicle has a
sunroof, the switch is
located on the headliner
between the map
lamps.
The sunroof will only operate while the ignition is
in ON or in ACC, or if Retained Accessory
Power (RAP) is active. SeeRetained Accessory
Power (RAP) on page 109.
Press the back of the switch and release it to
open the sunroof to the vent position. From the
vent position, press and release the back of
the switch to express-open the sunroof. To stop
the sunroof from express opening, press the switch
again. If the sunshade is closed, it will open
automatically when the sunroof opens past the
vented position.A de ector will automatically raise when the
sunroof is opened. The de ector will retract when
the sunroof is closed.
To close the sunroof, press the front of the switch
and hold it until the sunroof is closed. The
sunroof will stop if the switch is released. Close
the sunshade by hand.
The sunroof glass panel cannot be opened or
closed if the vehicle has an electrical failure.
Notice:If you force the sunshade forward of
the sliding glass panel, damage will occur
and the sunroof may not open or close
properly. Always close the glass panel before
closing the sunshade.
133
ProCarManuals.com
Page 139 of 406
The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on
page 160.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 141.
C. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 162.
D. Windshield Wiper and Washer Lever. See
Windshield Wipers on page 143andWindshield
Washer on page 144.
E. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 140.
F. Passenger Airbag Status Indicator. See
Passenger Airbag Status Indicator on page 165.
G. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 151.
H. Cruise Controls. SeeCruise Control on
page 145. Driver Information Center (DIC)
Buttons. SeeDriver Information Center (DIC)
on page 179.
I. Tilt Lever. SeeTilt and Telescopic Steering
Wheel on page 140.J. Horn. SeeHorn on page 140.
K. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 206.
L. Ignition Switch. SeeIgnition Positions on
page 108.
M. Automatic Climate Control System. See
Automatic Climate Control System on
page 154.
N. Traction Control Button. SeeTraction Control
System (TCS) on page 217. Electronic Stability
Control Button. SeeElectronic Stability
Control on page 219.
O. Shift Lever. SeeAutomatic Transaxle Operation
on page 116.
P. Audio System. SeeAudio System(s) on
page 192.
Q. Glove Box. SeeGlove Box on page 131.
139
ProCarManuals.com
Page 140 of 406
Hazard Warning Flashers
The hazard warning ashers let you warn the
police and others that you have a problem. The
front and rear turn signal lamps will ash on
and off.
The hazard warning
asher button is located
towards the center of
the instrument panel.
Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
While the hazard warning ashers are on, the turn
signals do not work.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not
in the ignition switch.
Other Warning Devices
If you carry re ective triangles, you can set them
up at the side of the road about 300 feet
(100 m) behind your vehicle.
Horn
Press near or on the horn symbols on the steering
wheel pad to sound the horn.
Tilt and Telescopic Steering Wheel
A tilt and telescope wheel lets you adjust the
steering wheel before you drive. The steering
wheel can be raised to the highest level to give
your legs more room when you enter and exit the
vehicle.
The lever that lets you tilt and telescope the
steering wheel is located on the left side of the
steering column.
140
ProCarManuals.com
Page 142 of 406
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions
let you signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever
returns automatically to the normal position.
An arrow on the
instrument panel cluster
ashes in the direction of
the turn or lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete your lane change. The lever returns
by itself when it is released.
If the arrows ash rapidly or do not go on at all as
you signal a turn or lane change, a signal bulb
could be burned out and other drivers will not see
your turn signal.
Replace burned out bulbs to help avoid an
accident. Also, check the appropriate fuses. See
Fuses on page 343.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high beam, push the turn signal/multifunction lever
toward the front of the vehicle.
This light on the
instrument panel cluster
comes on if the high
beam lamps are turned
on while the ignition
is on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward the rear
of the vehicle.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you that
you want to pass.
To use it, pull the turn signal/multifunction lever
toward you until the high-beam headlamps
come on, then release the lever to turn them off.
142
ProCarManuals.com
