2007 SAAB 9-7X turn signal

Programmable Locking Feature
Following are the two locking modes that can be
programmed:
Mode 1:All doors lock when the transmission is
shifted out of PARK (P).
Mode 2:All doors lock when the vehicle speed is
greater than 8 mph (13 km/h).
The automatic door locks were pre-programmed at
the factory to lock all the doors when the
transmission is shifted into gear. The following
instructions detail how to program your door
locks differently than the factory setting. Choose
one of the two programming options listed
previously before entering the program mode.
To enter the program mode, do the following:
1. Begin with the ignition off. Then pull the turn
signal/multifunction lever toward you and hold
it there while you perform the next step.
2. Turn the key to RUN and LOCK twice. Then,
with the key in LOCK, release the turn
signal/multifunction lever. Once you do this,
you will hear the lock switch lock and
unlock, the horn will chirp twice, and a
30-second program timer will begin.3. You are now ready to program the automatic
door locks. Select one of the two programming
options listed previously, and press the lock
side of the power door lock switch to
cycle through the lock options. You will have
30 seconds to begin programming. If you
exceed the 30-second limit, the locks
will automatically lock and unlock and the
horn will chirp twice to indicate that you have
left the program mode. If this occurs,
repeat the procedure beginning with Step 1 to
re-enter the programming mode.
You can exit the program mode any time by
turning the ignition to RUN. The locks will
automatically lock and unlock and the horn will
chirp twice to indicate that you are leaving
the program mode. If the lock/unlock switches are
not pressed while in the programming mode,
the current auto lock/unlock setting will not
be modied.
See your dealer for more information.
95
ProCarManuals.com

Programmable Unlocking Feature
The following is the list of available programming
options:
Mode 1:Driver’s door unlocks when the
transmission is shifted into PARK (P).
Mode 2:All doors unlock when the transmission
is shifted into PARK (P).
Mode 3:All doors unlock when the key is
removed from the ignition.
Mode 4:No automatic door unlock.
The automatic door locks were pre-programmed at
the factory to unlock all doors once the
transmission is shifted to PARK (P). The following
instructions detail how to program your door
locks differently than the factory setting. Choose
one of the four programming options listed
previously before entering the program mode.
To enter the program mode you need to do the
following:
1. Begin with the ignition off. Then pull the turn
signal/multifunction lever toward you and hold
it there while you perform the next step.2. Turn the key to RUN and LOCK twice. Then,
with the key in LOCK, release the turn
signal/multifunction lever. Once you do this,
you will hear the lock switch lock and
unlock, the horn will chirp twice, and a
30-second program timer will begin.
3. You are now ready to program the automatic
door locks. Select one of the four programming
options listed above, and press the unlock side
of the power door lock switch to cycle through
the unlocking options. You will have
30 seconds to begin programming. If you
exceed the 30-second limit, the locks will
automatically lock and unlock and the horn will
chirp twice to indicate that you have left the
program mode. If this occurs, repeat the
procedure beginning with Step 1 to re-enter the
programming mode.
You can exit the program mode any time by turning
the ignition to RUN. The locks will automatically
lock and unlock and the horn will chirp twice to
indicate that you are leaving the program mode.
If the lock/unlock switches are not pressed while in
the programming mode, the current auto lock/
unlock setting will not be modied.
See your dealer for more information.
96
ProCarManuals.com

5. After entering the switch settings, press and
release all three buttons at the same time.
The indicator lights will turn on.
6. Press and hold the button you would like to use
to control the garage door until the garage door
moves. The indicator light above the selected
button should slowly blink. You may need to
hold the button from ve to 55 seconds.
7. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
8. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1 through 8, choosing
a different function button in Step 7 than what
you used for the garage door opener.Programming Universal Home
Remote — Rolling Code
Rolling code garage door openers are used for
garage doors produced after 1996 and are
code protected. Rolling code means the coded
signal is changed every time your remote control
garage door opener is used.
Programming a rolling code garage door opener
involves time-sensitive actions, so read the
entire procedure before you begin. If you do not
follow these actions, the device will time out
and you will have to repeat the procedure.
Follow these steps to program up to three channels:
1. Press the two outside buttons at the same
time for one to two seconds, and immediately
release them.
133
ProCarManuals.com

4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for
two seconds and then turns to a constant light,
continue with Steps 6 through 8 following to
complete the programming of a rolling-code
device, most commonly, a garage door opener.6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release it.
Immediately press and hold the same button
a second time for two seconds, then
release it. Immediately, press and hold the
same button a third time for two seconds,
then release.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” Do not
repeat Step 1, as this will erase all previous
programming from the Universal Home Remote
buttons.
137
ProCarManuals.com

Instrument Panel Overview........................ 148
Hazard Warning Flashers.......................... 150
Other Warning Devices............................. 150
Horn.......................................................... 150
Tilt Wheel.................................................. 151
Turn Signal/Multifunction Lever.................. 151
Turn and Lane-Change Signals................. 152
Headlamp High/Low-Beam Changer.......... 153
Flash-to-Pass............................................ 153
Windshield Wipers..................................... 154
Windshield Washer.................................... 155
Rear Window Wiper/Washer...................... 155
Headlamp Washer..................................... 156
Cruise Control........................................... 156
Headlamps................................................ 160
Headlamps on Reminder........................... 160
Daytime Running Lamps (DRL)................. 161
Automatic Headlamp System..................... 161
Fog Lamps................................................ 162
Instrument Panel Brightness...................... 163
Dome Lamps............................................. 163
Dome Lamp Override................................ 163
Entry Lighting............................................ 164
Exit Lighting.............................................. 164
Reading Lamps......................................... 164Electric Power Management...................... 164
Battery Run-Down Protection..................... 165
Accessory Power Outlet(s)........................ 166
Climate Controls......................................... 167
Dual Automatic Climate Control System....... 167
Outlet Adjustment...................................... 172
Rear Climate Control System.................... 173
Climate Controls Personalization................ 173
Warning Lights, Gages, and Indicators..... 174
Instrument Panel Cluster........................... 175
Speedometer and Odometer...................... 176
Trip Odometer........................................... 176
Tachometer............................................... 176
Safety Belt Reminder Light........................ 177
Passenger Safety Belt Reminder Light....... 177
Airbag Readiness Light............................. 178
Passenger Airbag Status Indicator............. 179
Charging System Light.............................. 182
Voltmeter Gage......................................... 182
Brake System Warning Light..................... 183
Anti-Lock Brake System Warning Light...... 184
StabiliTrak
®Service Light........................... 185
StabiliTrak®Indicator Light......................... 185
Engine Coolant Temperature Gage............ 186
Section 3 Instrument Panel
145
ProCarManuals.com

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 172.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 151.
C. Audio Steering Wheel Controls. SeeAudio
Steering Wheel Controls on page 259.
D. Horn. SeeHorn on page 150.
E. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 175.
F. Windshield Wiper/Washer Lever. See
Windshield Wipers on page 154.
G. Hazard Warning Flashers Button and Driver
Information Center Buttons. SeeHazard
Warning Flashers on page 150orDriver
Information Center (DIC) on page 194.
H. Rear Window Washer/Wiper. SeeWindshield
Washer on page 155.
I. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 163.J. Hood Release. SeeHood Release on page 329.
K. Dome Lamp Override Button. SeeDome Lamp
Override on page 163.
L. Audio System. SeeAudio System(s) on
page 212.
M. Climate Controls. SeeDual Automatic Climate
Control System on page 167.
N. Gear Shift Lever. SeeAutomatic Transmission
Operation on page 112.
O. Ignition Switch. SeeIgnition Positions on
page 107.
P. Parking Brake. SeeParking Brake on
page 116.
Q. Accessory Power Outlet. SeeAccessory Power
Outlet(s) on page 166.
R. Cupholder. SeeCupholder(s) on page 139.
S. Glove Box. SeeGlove Box on page 139.
149
ProCarManuals.com

Hazard Warning Flashers
Your hazard warning ashers let you warn others.
They also let police know you have a problem.
Your front and rear turn signal lamps will ash on
and off.
The hazard warning
asher button is located
in the center of the
instrument panel.
Your hazard warning ashers work no matter what
position your key is in, and even if the key is
not in the ignition switch.Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
When the hazard warning ashers are on, your
turn signals will not work.
Other Warning Devices
If you carry reective triangles, you can set them up
at the side of the road about 300 feet (100 m)
behind your vehicle.
Horn
To sound the horn, press the horn symbols on the
steering wheel pad.
150
ProCarManuals.com

Tilt Wheel
The steering wheel should be adjusted before
you drive.
The tilt lever is located
to the left of the steering
column, under the
turn signal lever.
It can be raised to the highest level to give
your legs more room when you enter and exit
the vehicle.
To tilt the wheel, hold the steering wheel and pull
the lever toward you. Move the steering wheel
to a comfortable level, then release the lever
to lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. See
Turn and Lane-Change Signals on page 152.
OHeadlamps. SeeHeadlamps on page 160.
23Headlamp High/Low Beam-Changer.
SeeHeadlamp High/Low-Beam Changer on
page 153.
Flash-To-Pass Feature. SeeFlash-to-Pass on
page 153.
-Fog Lamps. SeeFog Lamps on page 162.
ICruise Control. SeeCruise Control on
page 156.
151
ProCarManuals.com