2007 RENAULT SCENIC engine

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 45V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
DF126
PRESENT
OR
STOREDCOMBINED SENSOR SIGNAL PLAUSIBILITY
NOTESSpecial notes:
This fault means that the combined sensor signals are not consistent with the other
ESP sensors (steering wheel angle sensor and wheel speed sensors). If the fault
appears while the vehicle is being driven on a steep gradient, during a very tight turn
or while the vehicle is being transported on a lorry, train, boat, etc., with the engine
running, clear the fault and if possible check that the fault has disappeared by carrying
out a road test.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Check the connection and condition of the combined sensor connector.
Ensure that the sensor is properly fixed to the body in the right direction (arrow pointing to the front of the vehicle).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Using the diagnostic tool, calibrate the steering wheel angle in the "Electric power steering" subgroup followed by
command RZ003 "ESP sensor programming" for Vdiag 09, 0A, 0B, 12 and 11 in the ABS/ESP.
Re-establish dialogue with the ABS/ESP computer, clear the computer fault memory, carry out a road test then
check again with the diagnostic tool.
If the fault is still present, adjust the axle assembly geometries. Adjust if necessary and use the diagnostic tool to
calibrate the steering wheel angle again in the "Electric power steering" subgroup, then run command RZ003 ESP
sensor programming for Vdiag 09, 0A, 0B, 12 and 11 in the ABS/ESP.
Carry out a road test.
If the fault is still present, replace the sensor.
AFTER REPAIRClear the computer fault memory. If the combined sensor has been replaced, erase the
ESP sensor programming (Vdiag 09, 0A, 0B and 11) with command RZ003 ESP
sensor programming.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF126 /ESPBOSCH_V09_DF126/ESPBOSCH_V0A_DF126/
ESPBOSCH_V0B_DF126 /ESPBOSCH_V11_DF126/ESPBOSCH_V12_DF126
MR-372-J84-38C050$496_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 48V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF186
PRESENT
OR
STOREDINSTRUMENT PANEL MULTIPLEX SIGNAL ABSENT
NOTESSpecial notes:
Even though it is stored in the computer, this fault does not cause the warning lights to
come on or a fault message. Using the diagnostic tool, run fault finding on the
instrument panel.
Note:
Once the fault in the instrument panel system has been remedied, clear the ABS/ESP
computer fault memory.
The multiplex signal from the instrument panel is sent to the ABS/ESP via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector of the UPC (Vdiag 44) or the grey CT1
connector of the UPC (Vdiag 48 or higher).
Carry out a multiplex network test.
If the fault is still present, perform fault finding on the instrument panel and repair accordingly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF186 /ESPBOSCH_V09_DF186/ESPBOSCH_V0A_DF186/
ESPBOSCH_V0B_DF186 /ESPBOSCH_V11_DF186/ESPBOSCH_V12_DF186

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 54V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF193
PRESENT
OR
STOREDINVALID INJECTION MULTIPLEX SIGNALS
NOTESSpecial notes:
Although it is stored in the computer, the ABS/ESP system is not faulty. The ESP is
deactivated due to unusable information from the injection system. Perform fault
finding on the injection system using the diagnostic tool.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP
system.
If no fault is stored in the injection computer, start the engine; if there is no fault present,
contact the Techline. Once the fault in the injection system has been repaired, clear
the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
Carry out a multiplex network test and check the injection system with the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF193 /ESPBOSCH_V09_DF193/ESPBOSCH_V0A_DF193/
ESPBOSCH_V0B_DF193 /ESPBOSCH_V11_DF193/ESPBOSCH_V12_DF193

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 55V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF194
PRESENT
OR
STOREDELECTRIC POWER ASSISTED STEERING MULTIPLEX SIGNALS
INVALID
1.DEF : inconsistency
2.DEF : fault detected
NOTESSpecial notes:
Although it is stored in the computer, the ABS/ESP system is not faulty. The ESP is
deactivated due to unusable information from the electric power steering system. Run
fault finding on the electric power steering with the diagnostic tool.
Note:
The electric power steering does not always store these transient faults as quickly as
the ABS/ESP system.
If no fault is stored in the electric power steering computer memory, start the engine; if
no present fault is displayed, contact the Techline. Once the fault in the electric power
steering system has been repaired, clear the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
1.DEF
NOTESNone
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of
the tyres.
Check the axle assemblies, adjust if necessary.
Calibrate the steering wheel angle in the electric power-assisted steering using the diagnostic tool.
Ensure that the combined sensor is properly fixed to the body in the right direction (arrow towards the front of
the vehicle).
If all the checks are OK, clear the computer fault memory and clear the ESP sensor programming (Vdiag 09, 0A,
0B, 12 and 11) using command RZ003 "ESP sensor programming".
Carry out a road test.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF194 /ESPBOSCH_V09_DF194/ESPBOSCH_V0A_DF194/
ESPBOSCH_V0B_DF194 /ESPBOSCH_V11_DF194/ESPBOSCH_V12_DF194

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 57V2 MR-372-J84-38C050$496_eng.mif
NO
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF195
PRESENT
OR
STOREDAUTOMATIC GEARBOX MULTIPLEX SIGNALS INVALID
NOTESSpecial notes:
Although it is stored in the computer, this fault does not cause the warning lights to
come on or generate a fault message, because the ABS/ESP system is not faulty. The
ABS/ESP system is not faulty, but has received unusable signals from the automatic
transmission. Run fault finding on the automatic transmission with the diagnostic tool.
Note:
The automatic transmission does not always store these transient faults as quickly as
the ABS/ESP.
If there is no stored fault in the automatic transmission computer memory, start the
engine, and if no present fault is displayed, contact the Techline. Once the fault in the
automatic transmission has been repaired, clear the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
Using the diagnostic tool, check in the parameter screen that the PR063 Vehicle parameters truly correspond with
the vehicle undergoing fault finding.
Is PR063 Vehicle Parameters correct?
YES
Carry out a multiplex network test and check the automatic transmission system using
the diagnostic tool.
If the fault is still present, contact the Techline.
Use command VP004 Vehicle parameters to define the appropriate parameters for the
vehicle type.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a new test with the diagnostic
tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF195 /ESPBOSCH_V09_DF195/ESPBOSCH_V0A_DF195/
ESPBOSCH_V0B_DF195 /ESPBOSCH_V11_DF195/ESPBOSCH_V12_DF195

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 58V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF196
PRESENT
OR
STOREDNO ELECTRIC POWER ASSISTED STEERING MULTIPLEX
SIGNAL
NOTESSpecial notes:
Although the fault is stored in the computer, it is not caused by ABS/ESP components,
but it indicates that the ESP is deactivated due to an electric power steering frame
transmission fault. Run fault finding on the electric power steering.
Note:
The electric power steering does not always store these transient faults as quickly as
the ABS/ESP system.
If there is no stored fault in the electric power steering computer memory, start the
engine; if no present fault is displayed, contact the Techline. Once the fault in the
electric power steering system has been repaired, clear the ABS/ESP computer fault
memory.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector on the UPC (Vdiag 44) or the grey CT1
connector on the UPC (Vdiag 48).
Carry out a multiplex network test and check the electric power steering system using the diagnostic tool. If the
fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF196 /ESPBOSCH_V09_DF196/ESPBOSCH_V0A_DF196/
ESPBOSCH_V0B_DF196 /ESPBOSCH_V11_DF196/ESPBOSCH_V12_DF196

38C-69
MR-372-J84-38C050$930_eng.mif
V2
38C
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
ALP 1 No dialogue with the ABS computer
NOTESSpecial note:
To run fault finding on the vehicle's computers, switch on the ignition in fault finding
mode (forced + after ignition feed), i.e. proceed as follows:
–With the vehicle card in the card reader, press the Start button for more than
5 seconds without starting conditions being met.
Check that the CLIP diagnostic tool is equipped with the latest update available.
Try to establish dialogue with a computer on another vehicle to make sure that the diagnostic tool is not faulty.
If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle, the
cause could be a faulty computer interfering on the multiplex network. Check the battery voltage and carry out the
operations necessary to obtain the correct voltage (9.5 V < battery voltage < 17.5 V).
Carry out a fault finding procedure on the multiplex network using the diagnostic tool.
Check the presence and the condition of the ABS fuses on the passenger compartment fuse board and in the
engine fuse box.
Check that the computer connector is properly connected and check the condition of its connections.
Check the ABS earths (good condition, not corroded, earth screw on top of the ABS unit tight).
Check that the supply to the computer is correct:
–Earth on tracks 1 and 4 of the 46-track connector.
–+ before ignition feed on tracks 2 and 3 of the 46-track connector.
–+ after ignition feed on track 18 of the 46-track connector.
Check that the power supply to the diagnostic socket is correct:
–+ before ignition feed on track 16.
–+ after ignition feed on track 1.
–Earth on tracks 4 and 5.
If dialogue has still not been established after these checks, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP01 /ESPBOSCH_V09_ALP01/ESPBOSCH_V0A_ALP01/
ESPBOSCH_V0B_ALP01 /ESPBOSCH_V11_ALP01/ESPBOSCH_V12_ALP01BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
MR-372-J84-38C050$930_eng.mif

38C-71
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 3 Pull
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Disconnect one wheel speed sensor. Start the
engine and check that only the ABS fault warning
light comes on. Do not drive the vehicle if the brake
fault warning light is also lit, as the brake limiter
function is no longer guaranteed to operate
correctly. Carry out a road test with the ABS
deactivated.
Is the fault still present under these conditions?
no
Raise the vehicle so that you can rotate the wheels
and check:
–Possible inversion when connecting the speed
sensors.
–Possible inversion of pipes on the hydraulic unit.
To carry out these two tests, refer to and follow the
procedures given in ALP 2.
Check the condition of the ABS targets and that they
conform to specifications.
Also check the sensor/target air gap over one
revolution of each front and rear wheel.
If the fault is still present, contact the Techline.
yesIf the brake pedal travel is relatively long,
bleed the brake circuit.
If the travel is normal, check the tyre
pressures, the front axle, or for any leaks
in the circuit.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP03 /ESPBOSCH_V09_ALP03/ESPBOSCH_V0A_ALP03/
ESPBOSCH_V0B_ALP03 /ESPBOSCH_V11_ALP03/ESPBOSCH_V12_ALP03BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12