2007 RENAULT SCENIC ignition

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 35V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF091
STORED
LEFT-HAND FRONT WHEEL TARGET
NOTESSpecial notes:
This fault means that some magnetic poles of the target are not detected by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Check for play in the bearing.
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check the quality of the mounting of the wheel speed sensor (correct clipping without excessive play).
Check the sensor/target air gap over one wheel revolution: 0.1 mm < front wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the instrumented bearing if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF091 /ABS8.0_V0D_DF091/ABS8.0_V0E_DF091/ABS8.0_V0F_DF091 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 36V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF092
STORED
RIGHT-HAND REAR WHEEL TARGET
NOTESSpecial notes:
This fault means that some of the target teeth are not seen by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor / target air gap over one wheel rotation: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the rear right-hand "disc-hub-bearing" assembly (see MR364 or MR370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF092 /ABS8.0_V0D_DF092/ABS8.0_V0E_DF092/ABS8.0_V0F_DF092 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 37V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF093
STORED
LEFT-HAND REAR WHEEL TARGET.
NOTESSpecial notes:
This fault means that some of the target teeth are not seen by the sensor.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap over one wheel rotation: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
Replace the rear left-hand "disc-hub-bearing" assembly (see MR364 or MR370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the number of teeth is incorrect.
If all the checks are correct, reconnect the computer and the wheel speed sensor.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a road test.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF093 /ABS8.0_V0D_DF093/ABS8.0_V0E_DF093/ABS8.0_V0F_DF093 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of statuses
38C
38C - 45V2 MR-372-J84-38C000$660_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of statuses
ET017
BRAKE PEDAL
NOTESSpecial notes:
Carry out the checks only if the "pressed" and "released" statuses are not
consistent with the pedal position.
STATUS IS "RELEASED" WITH BRAKE PEDAL PRESSED.
If brake lights operate:
–Check the continuity of the connection between track 1 of the brake light switch connector and track 20 of the
computer connector.
If the brake lights do not operate:
–Check the condition and fitting of the brake light switch and brake lights fuse.
–Remove the brake light switch and check that it is operating correctly:
Continuity between tracks Insulation between tracks
Switch pressed
(Brake pedal released)3 and 4 1 and 2
Switch released
(Brake pedal depressed)1 and 2 3 and 4
Replace the switch if necessary.
Check for + after ignition feed on tracks 2 and 4 on the brake light switch connector.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_ET017/ ABS8.0_V0D_ET017/ABS8.0_V0E_ET017/ABS8.0_V0F_ET017 ABS 8.0X84 4.0
MR-372-J84-38C000$660_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Parameter procedures
38C
38C - 47V2 MR-372-J84-38C000$726_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Parameter procedures
PARAMETERS
PR001:Front right-hand wheel speed.
PR002:Front left-hand wheel speed.
PR003:Rear right-hand wheel speed.
PR004:Rear left-hand wheel speed
These parameters show the speed of each wheel of the vehicle in mph.
PR005:Computer supply.
This parameter shows the computer's + after ignition feed voltage in volts.
PR020:Vehicle speed at initialisation
This parameter shows the vehicle speed sent to the multiplex network when the computer is initialised.
(vdiag 0F)
PR030:Tachometric index.
This parameter specifies the tachometric index entered in the computer for the tyres fitted to the vehicle.
PR038:Vehicle speed.
This parameter indicates the vehicle speed in mph (km/h).
PR063:Vehicle parameters
This parameter shows whether the configuration (VP004) correctly matches the vehicle being tested.
(vdiag 0F)
ABS 8.0X84 4.0
MR-372-J84-38C000$726_eng.mif

ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
38C
38C - 51V2 MR-372-J84-38C000$924_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
ALP1 No dialogue with the ABS computer
NOTESSpecial notes:
To run fault finding on the vehicle's computers, switch on the ignition in fault
finding mode (forced + after ignition feed). Proceed as follows:
–with the vehicle card in the card reader, press the Start button for more than
5 seconds outside of starting conditions.
Check that the CLIP diagnostic tool is equipped with the latest update available.
Check that the diagnostic tool is not causing the fault by trying to establish dialogue with a computer on another
vehicle. If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle,
the cause could be a faulty computer interfering on the multiplex network. Check the battery voltage and carry out
the necessary work to obtain the correct voltage (9.5 V < battery voltage < 17.5 V).
Carry out a fault finding procedure on the multiplex network using the diagnostic tool.
Check the presence and the condition of the ABS fuses on the passenger compartment fuse board and in the
engine fuse box. Check that the computer connector is properly connected and check the condition of its
connections. Check the ABS earths (good condition, not corroded, tightness of the earth screw above the ABS
assembly). Check that the supply to the computer is correct:
–Earth on tracks 1 and 4 of the 26-track connector.
–+ before ignition feed on tracks 2 and 3 of the 26-track connector.
–+ after ignition feed on track 18 of the 26-track connector.
Check that the power supply to the diagnostic socket is correct:
–+ before ignition feed on track 16.
–+ after ignition feed on track 1.
–Earth on tracks 4 and 5.
If dialogue has still not been established after these checks, contact the Techline.
AFTER REPAIRClear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_ALP01 /ABS8.0_V0D_ALP01/ABS8.0_V0E_ALP01/ABS8.0_V0F_ALP01 ABS 8.0X84 3.0
MR-372-J84-38C000$924_eng.mif

ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
38C
38C - 57V2 MR-372-J84-38C000$924_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
ALP7Unexpected ABS operation when using special equipment
(car phone, CB, etc.)
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the equipment which is causing the fault is approved.
Check that this equipment has been correctly installed without modification to the original wiring, in particular, that
of the ABS (connections to earth and + after ignition/before ignition feed of the ABS are not permitted).
AFTER REPAIRClear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_ALP07 /ABS8.0_V0D_ALP07/ABS8.0_V0E_ALP07/ABS8.0_V0F_ALP07 ABS 8.0X84 3.0

ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
38C
38C - 62V2 MR-372-J84-38C000$924_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
ALP12ABS computer not detected during the multiplex network test
on CLIP
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the CLIP diagnostic tool is equipped with the latest update available.
After the multiplex network test on the CLIP, if the ABS computer is not detected, carry out the following operations:
–return to the home menu of the CLIP screen,
–switch off the ignition,
–switch on the ignition again,
–test the computers against without making the automatic VIN code acquisition.
If the fault is still present, follow ALP 1.
AFTER REPAIRClear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_ALP12 /ABS8.0_V0D_ALP12/ABS8.0_V0E_ALP12/ABS8.0_V0F_ALP12 ABS 8.0X84 3.0