2007 RAM CHASSIS CAB battery

▫ Catalytic Converter (Gas Engines) .........413
▫ Intervention Regeneration Strategy – EVIC
Message Process Flow (Catalyst Full Message)
(Diesel Engines Only) ..................415
▫ Emission-Related Components (Gas Engines) . . 418
▫ Maintenance Free Battery (Gas Engines) .....418
▫ Maintenance Free Batteries (Diesel Engines) . . . 419
▫ Air Conditioner Maintenance .............420
▫ Power Steering — Fluid Check ............421
▫ Front Suspension Ball Joints ..............422
▫ Steering Linkage — Inspection ............422
▫ Front Prop Shaft Lubrication .............422
▫ Front Axle Universal Drive Joints And Pivot
Bearings ............................423 ▫ Body Lubrication .....................423
▫ Windshield Wiper Blades ................424
▫ Windshield Washers ...................424
▫ Exhaust System ......................425
▫ Cooling System .......................426
▫ Fan ...............................432
▫ Charge Air Cooler — Inter-Cooler (Diesel
Engines) ............................432
▫ Hoses And Vacuum/Vapor Harnesses .......433
▫ Fuel System Connections ................433
▫ Brake System ........................434
▫ Clutch Hydraulic System ................436
▫ Clutch Linkage .......................436390 MAINTAINING YOUR VEHICLE

Drive Belts (Gas Engines)
Belt tension is controlled by means of an automatic
tensioner. No belt tension adjustments are required.
However, belt and belt tensioner condition should be
inspected at the specified intervals and replaced if re-
quired. See your authorized dealer for service.
At the mileage indicated in the maintenance schedule, all
belts and tensioner should be checked for condition.
Improper belt tension can cause belt slippage and failure.
Belts should be inspected for evidence of cuts, cracks,
glazing or frayed cords and replaced if there is indication
of damage which could result in belt failure. Low gen-
erator belt tension can cause battery failure.
Also check belt routing to make sure there is no interfer-
ence between the belts and other engine components. Drive Belt (Diesel Engines)
Inspection
Check the belt for intersecting cracks.
• Transverse (across the belt width) cracks are accept-
able.
• Longitudinal (direction of belt length) cracks that
intersect with transverse cracks are NOT acceptable.
Replace the belt if it has unacceptable cracks, is frayed or
has pieces of material missing.
The engine speed sensor, located near the damper, should
be inspected for damage if a belt is frayed.
Engine Air Cleaner Filter (Gas Engines)
Under normal driving conditions, replace the air filter at
the intervals shown on Schedule “A”. If, however, you406 MAINTAINING YOUR VEHICLE

Emission-Related Components (Gas Engines)
Positive Crankcase (PCV) Valve
Proper operation of the crankcase ventilation system
requires that the PCV valve be free of sticking or plug-
ging from deposits. Deposits can accumulate in the PCV
valve and passages with increasing mileage. Have the
PCV valve, hoses, and passages checked for proper
operation at the intervals specified. If the valve is
plugged or sticking, replace with a new valve— do not
attempt to clean the old PCV valve! Check the ventila-
tion hoses for indications of damage, weepage or plug-
ging with deposits. Replace if necessary.
Maintenance Free Battery (Gas Engines)
The top of the maintenance free battery is permanently
sealed. You will never have to add water, nor is periodic
maintenance required. WARNING!• Battery fluid is a corrosive acid solution and can
burn or even blind you. Don’t allow battery fluid
to contact your eyes, skin or clothing. Don’t lean
over a battery when attaching clamps. If acid
splashes in eyes or on skin, flush the area imme-
diately with large amounts of water.
• Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Don’t use
a booster battery or any other booster source with
an output greater than 12 volts. Don’t allow cable
clamps to touch each other.
• Battery posts, terminals and related accessories
contain lead and lead compounds. Wash hands
after handling.418 MAINTAINING YOUR VEHICLE

CAUTION!• It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked (+)
positive and negative (-) and identified on the
battery case.
• If a “fast charger” is used while battery is in
vehicle, disconnect both vehicle battery cables
before connecting the charger to battery. Do not
use a “fast charger” to provide starting voltage.
Maintenance Free Batteries (Diesel Engines)
The top of the maintenance free batteries are perma-
nently sealed. You will never have to add water, nor is
periodic maintenance required. NOTE: Replacement batteries should both be of equal
capacity to prevent damage to the vehicle’s charging
system.
CAUTION!It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to the
negative post. Battery posts are marked (+) positive
and negative (-) and identified on the battery case.
Also, if a “fast charger” is used while battery is in
vehicle, disconnect both vehicle battery cables be-
fore connecting the charger to battery. Do not use a
“fast charger” to provide starting voltage. MAINTAINING YOUR VEHICLE 419
7

WARNING!Battery posts, terminals, and related accessories con-
tain lead and lead compounds. Always wash hands
after handling the battery.
Battery Blanket Usage
A battery loses 60% of its cranking power as the battery
temperature decreases to 0°F (-18°). For the same de-
crease in temperature, the engine requires twice as much
power to crank at the same RPM. The use of 120 VAC
powered battery blankets will greatly increase starting
capability at low temperatures. Suitable battery blankets
are available from your authorized Mopar  dealer. Air Conditioner Maintenance
For best possible performance, your air conditioner
should be checked and serviced by an Authorized Dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt tension should also be checked at this
time.
NOTE: Refer to Section 3 of the Warranty Information
book for further warranty information.420 MAINTAINING YOUR VEHICLE

FUSES (INTEGRATED POWER MODULE)
An integrated Power Module is located in the engine
compartment near the battery. This center contains car-
tridge fuses and mini fuses. A description of each fuse
and component may be stamped on the inside cover
otherwise the cavity number of each fuse is stamped on
the inside cover that corresponds to the following chart. Cavity Cartridge
Fuse Mini
Fuse Description
1 20 Amp
Yellow Power Outlet Console
2 20 Amp
Yellow Cabin Compartment
Node (CCN) Door
Locks/Brake Trans-
mission Shift Interlock
(BTSI)
3––
4 15 Amp
Blue Aisin Transmission
Controls (Diesel Only)
5 20 Amp
Yellow Power Sunroof
6 10 Amp
Red VIST Fan/Wastegate
7 15 Amp
Blue Reverse Lockout Sole-
noid Battery (SRT-10
Only)
Integrated Power Module Location MAINTAINING YOUR VEHICLE 457
7

Cavity Cartridge
Fuse Mini
Fuse Description
8 10 Amp
Red Heated Mirrors
9 30 Amp
Pink Off Road Module
Power
10 5 Amp
Orange Trx-Off Rd Pkg Sen
(Gas Engine Only)
NOTE: Insert a 5 amp fuse in this cavity to enable
the TRX capability.
11 20 Amp
Yellow Ignition Off Draw
(IOD)-Cabin Compart-
ment Node (CCN)/
Radio/Under Hood
Lamp/Wireless Con-
trol Module (WCM)/
Satellite Digital Audio
Receiver (SDARS)/
Hands Free Module
(HFM) Cavity Cartridge
Fuse Mini
Fuse Description
12 30 Amp
Pink Electric Brake
13 25 Amp
Natural Power-Battery
RWAL/ABS Module
Feed
14 15 Amp
Blue Park Lamps Left
15 20 Amp
Yellow Trailer Park Lamps
16 15 Amp
Blue Park Lamps Right
17 – –
18 40 Amp
Green ABS Pump
19 30 Amp
Pink Trailer Tow
20 10 Amp
Red Occupant Restraints
Controller (ORC) 2458 MAINTAINING YOUR VEHICLE

VEHICLE STORAGE
If you are storing your vehicle for more than 21 days, we
recommend that you take the following steps to mini-
mize the drain on your vehicle’s battery:
• Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse
located in the Integrated Power Module, located in the
engine compartment. The I.O.D. cavity includes a
snap-in retainer that allows the fuse to be discon-
nected, without removing it from the fuse block.
• The electronic shift transfer case should be placed in
the 4HI mode and kept in this position to minimize the
battery drain.
• As an alternative to the above steps you may, discon-
nect the negative cables from both batteries.
• Anytime you store your vehicle, or keep it out of
service (i.e. vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will
insure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
NOTE: When reinstalling the IOD fuse push firmly until
fully seated, the gages in the Instrument Cluster will do
a full sweep, when the ignition key is cycled to RUN. This
is a normal condition.
REPLACEMENT LIGHT BULBS
LIGHT BULBS — Inside Bulb No.
Overhead Console Lights ............... TS 212-2
Dome Light ............................ 7679
NOTE: For lighted switches, see your dealer for replace-
ment instructions.
All of the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved. MAINTAINING YOUR VEHICLE 461
7