2007 PONTIAC GRAND PRIX ignition

TRACTION CONTROL ACTIVE
This symbol comes on
with this message.
If the vehicle has the Traction Control System
(TCS), this message displays when the system is
on. TRACTION CONTROL ACTIVE also
appears in the Head-Up Display (HUD), if your
vehicle has this feature.
This message only displays while the ignition is in
RUN and will not disappear until driving
conditions change and the TCS is no longer
active.
This message cannot be acknowledged or cleared
from the screen.
TRACTION CONTROL OFF
This symbol comes on
with this message.
If the vehicle has the Traction Control System
(TCS), this message displays when the TCS turns
off. TRACTION CONTROL OFF also appears
in the Head-Up Display (HUD), if your vehicle has
this feature. This message only displays while
the ignition is in RUN and disappears after
three seconds. A chime sounds once and the
message stays on for three seconds and
then disappears. A warning light indicating that
this system is deactivated also appears on
the instrument panel cluster. SeeTraction Control
System (TCS) Warning Light on page 178or
Enhanced Traction System Warning Light
on page 179.
225

Any of the following conditions may cause the
TCS to turn off:
The TCS is turned off by pressing the
TC (traction control) button located on
the center console. SeeTraction Control
System (TCS) on page 292orEnhanced
Traction System (ETS) on page 293for more
information.
The battery is low.
There is a TCS failure. See your dealer for
service.
TURN SIGNAL ON
This message displays if the vehicle is driven for
more than 0.75 mile (1.21 km) while one of
the turn signals are on. It appears as a reminder
to turn off the turn signal.
This message only displays when the ignition is in
RUN. A chime sounds for two seconds and the
message will not disappear until the turn signal is
manually turned off, or a turn is completed.
DIC Vehicle Customization
Your vehicle may have customization capabilities
that allow you to program certain features to
one preferred setting. Customization features can
only be programmed to one setting on the
vehicle and cannot be programmed to a preferred
setting for two different drivers.
All of the customization options may not be
available on your vehicle. Only the options
available will be displayed on your DIC.
The default settings for the customization features
were set when your vehicle left the factory, but
may have been changed from their default
state since then. The customization preferences
are automatically recalled.
To change customization preferences, use the
following procedure.
226

Entering the Personal Programming Mode
1. Turn the ignition on and make sure the
vehicle is in PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press the options button until PERSONAL
PROGRAMMING MODE appears on the DIC.
3. Press the set/reset button to display the rst
screen.
4. Press the options button to access these
modes:
Personal Programming Mode Screens
EXTERIOR LIGHTING DELAY:This screen
allows this feature to be turned off, or allows the
selection of the number of seconds the headlamps,
sidelamps, taillamps, fog lamps, and back-up
lamps are turned on after the key is removed from
the ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
If OFF is selected, the exterior lamps will not
turn on.If a time delay is chosen, the lamps will turn on for
the selected time. The time delay will be
cancelled and the exterior lamps will turn on
automatically when the key is removed from the
ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to the selection you want to program.
Choose from OFF, 15, 30, 60, or 90 seconds.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN DOOR CLOSED:This
screen allows this feature to be turned OFF or ON.
If OFF is selected, the interior lamps will turn off
immediately when the ignition is turned off and the
last open door is closed.
If ON is selected, the interior lamps will stay on for
about 25 seconds after the vehicle’s ignition is
turned off and the last open door is closed.
227

To program this mode, use the following procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN KEY REMOVED:This
screen allows this feature to be turned OFF or
ON. This feature enables the interior lamps in the
vehicle to turn on for about 25 seconds after
the key is removed from the ignition.
If OFF is selected, removing the key from the
ignition will not cause the interior lamps to turn on.
If ON is selected, removing the key from the
ignition will cause the interior lamps to be turned
on for about 25 seconds.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.AUTO DOOR UNLOCK:This screen allows this
feature to be turned off, used for the driver’s
door only, or for all the doors.
If OFF is selected, none of the doors will unlock
when the vehicle’s transaxle is shifted into
PARK (P).
If DRIVER is selected, only the driver’s door will
unlock when the vehicle’s transaxle is shifted
into PARK (P).
If ALL is selected, all the doors will unlock when
the vehicle’s transaxle is shifted into PARK (P).
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF, DRIVER, or ALL.
2. Press the options button again to advance to
the next screen.
228

AUTO DOOR UNLOCK ON:If DRIVER or ALL
was selected on the AUTO DOOR UNLOCK
screen, this screen allows selection of when the
vehicle’s doors will unlock. The choices are
when the key is removed from the ignition or when
the vehicle is shifted into PARK (P).
If KEY-OUT is selected, the auto door unlock will
function when the key is taken out of the
ignition.
If PARK is selected, the auto door unlock will
function when the transaxle is shifted into
PARK (P).
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either KEY-OUT or PARK.
2. Press the options button again to advance to
the next screen.DELAYED LOCKING:This screen allows this
feature to be turned OFF or ON. The key must be
out of the ignition for this feature to work.
If OFF is selected, there will be no delayed locking
of the vehicle’s doors.
If ON is selected, the locking of the vehicle’s
doors will be delayed by ve seconds after
a power door lock switch is pressed while the door
is open, or the LOCK button on the remote
keyless entry transmitter is pressed while any door
is open.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.
229

If ON is selected, the content theft-deterrent
system can be armed using the driver’s door lock
switch by pressing the driver’s door lock switch
while the driver’s door is open and the key is not in
the ignition, or by pressing the front passenger’s
door lock switch while the front passenger’s door is
open and the key is not in the ignition.
To program this mode, use the following
procedure:
1. Press the set/reset button to scroll to
OFF or ON.
2. Press the options button again to advance to
the next screen.
REMOTE START:If your vehicle has the remote
start feature, this screen allows this feature to
be turned OFF or ON. The remote start feature
allows you to start the engine from outside of the
vehicle using your remote keyless entry
transmitter. See “Remote Vehicle Start” under
Remote Keyless Entry (RKE) System Operation on
page 87for more information.If OFF is selected, the remote start feature will be
disabled.
If ON is selected, the remote start feature will be
enabled.
To program this mode, use the following
procedure:
1. Press the set/reset button to scroll to
OFF or ON.
2. Press the options button again to advance to
the next screen.
PROGRAMMING FINISHED will appear on the
next screen. This conrms that the personal
options programming is complete.
232

While your vehicle is parked:
Familiarize yourself with all of its controls.
Familiarize yourself with its operation.
Set up your audio system by presetting your
favorite radio stations, setting the tone, and
adjusting the speakers. Then, when driving
conditions permit, you can tune to your favorite
radio stations using the presets and steering
wheel controls if the vehicle has them.
Notice:Before adding any sound equipment
to your vehicle, such as an audio system,
CD player, CB radio, mobile telephone,
or two-way radio, make sure that it can be
added by checking with your dealer. Also,
check federal rules covering mobile radio and
telephone units. If sound equipment can be
added, it is very important to do it properly.
Added sound equipment may interfere with the
operation of your vehicle’s engine, radio, or
other systems, and even damage them.
Your vehicle’s systems may interfere with the
operation of sound equipment that has
been added.Notice:The chime signals related to safety
belts, parking brake, and other functions
of your vehicle operate through the
radio/entertainment system. If that equipment
is replaced or additional equipment is added
to your vehicle, the chimes may not work. Make
sure that replacement or additional equipment
is compatible with your vehicle before
installing it. SeeAccessories and Modifications
on page 336.
Your vehicle has a feature called Retained
Accessory Power (RAP). With RAP, the audio
system can be played even after the ignition
is turned off. SeeRetained Accessory
Power (RAP) on page 106for more information.
Setting the Time
The radio may have a button marked with an H or
HR to represent hours and an M or MIN to
represent minutes.
234

Press and hold the hour button until the correct
hour appears on the display. AM will appear
for morning hours. Press and hold the minute
button until the correct minute appears on
the display. The time can be set with the ignition
on or off.
To synchronize the time with an FM station
broadcasting Radio Data System (RDS)
information, press and hold the hour and minute
buttons at the same time until UPDATED appears
on the display. If the time is not available from
the station, NO UPDATE will appear on the
display.
RDS time is broadcast once a minute. After tuning
to an RDS broadcast station, it may take a
few minutes for the time to update.Radio with CD (Base Level)
Radio Data System (RDS)
The audio system has a Radio Data System (RDS).
RDS features are available for use only on FM
stations that broadcast RDS information.
With RDS, the radio can do the following:
Seek to stations broadcasting the selected
type of programming
Receive announcements concerning local and
national emergencies
Display messages from radio stations
Seek to stations with traffic announcements
235