2007 PONTIAC G5 ignition

Parking Brake
The parking brake lever is located between the
front seats.
For vehicles equipped with an armrest, lift the
console armrest in order to access the parking
brake lever.To set the parking brake, hold the brake pedal
down and pull up on the parking brake lever. If the
ignition is on, the brake system warning light will
come on. SeeBrake System Warning Light
on page 165.
To release the parking brake, hold the brake pedal
down. Pull the parking brake lever up until you can
press the release button. Hold the release button in
as you move the brake lever all the way down.
If you forget to release your parking brake, a chime
will sound and the PARKING BRAKE message
will appear along with the brake system warning
light when the parking brake is applied and
the vehicle is moving faster than 5 mph (8 km/h).
SeeDIC Warnings and Messages on page 177.
Notice:Driving with the parking brake on can
overheat the brake system and cause
premature wear or damage to brake system
parts. Verify that the parking brake is fully
released and the brake warning light is
off before driving.
118

Shifting Into Park (P)
(Automatic Transaxle)
{CAUTION:
It can be dangerous to get out of your
vehicle if the shift lever is not fully in
PARK (P) with the parking brake rmly set.
Your vehicle can roll. If you have left the
engine running, the vehicle can move
suddenly. You or others could be injured.
To be sure your vehicle will not move, even
when you are on fairly level ground, use
the steps that follow. If you are pulling a
trailer, seeTowing a Trailer (Manual
Transaxle) on page 256orTowing a Trailer
(Automatic Transaxle) on page 257.1. Hold the brake pedal down and set the
parking brake.
2. Move the shift lever into PARK (P) by holding
the button on the shift lever and pushing the
lever all the way toward the front of the
vehicle.
3. Turn the ignition key to LOCK.
4. Remove the key and take it with you. If you
can leave your vehicle with the ignition key in
your hand, your vehicle is in PARK (P).
119

Shifting Out of Park (P)
(Automatic Transaxle)
This vehicle is equipped with an electronic shift
lock release system. The shift lock release is
designed to:
Prevent ignition key removal unless the shift
lever is in PARK (P) with the shift lever
button fully released, and
Prevent movement of the shift lever out of
PARK (P) unless the ignition is in a position
other than LOCK.
The shift lock release is always functional except
in the case of a an uncharged or low voltage
(less than 9 volt) battery.
If your vehicle has an uncharged battery or a
battery with low voltage, try charging or jump
starting the battery. SeeJump Starting on
page 304for more information.To shift out of PARK (P) use the following
sequence:
1. Apply the brake pedal.
2. Then press the shift lever button.
3. Move the shift lever to the desired position.
If you still are unable to shift out of PARK (P):
1. Fully release the shift lever button.
2. While holding down the brake pedal, press
the shift lever button again.
3. Move the shift lever to the desired position.
If you still cannot move the shift lever from
PARK (P), consult your dealer or a professional
towing service.
121

Sunroof
If the vehicle has a
sunroof, the switch that
operates it is located
on the headliner
between the map lamps.
The sunroof will only operate while the ignition is
on, or turned to ACC, or if Retained Accessory
Power (RAP) is active. SeeRetained Accessory
Power (RAP) on page 110.
Press the sunroof switch rearward to open the
sunroof to the vent position. If the sunshade
is closed, it must be opened manually in the vent
position. Press and hold the switch rearward a
second time to open the sunroof. If the sunshade
is closed, it will open automatically when the
sunroof is opened.To close the sunroof, press the switch forward and
hold it until the sunroof is closed. The sunroof
will stop if the switch is released. Close the
sunshade by hand.
The sunroof glass panel cannot be opened or
closed if the vehicle has an electrical failure.
Notice:If you force the sunshade forward of
the sliding glass panel, damage will occur
and the sunroof may not open or close
properly. Always close the glass panel before
closing the sunshade.
132

Hazard Warning Flashers
Your hazard warning ashers let you warn others.
They also let police know you have a problem.
Your front and rear turn signal lamps will ash
on and off.
The hazard warning
asher button is located
in the center of the
instrument panel.
Your hazard warning ashers work no matter what
position your key is in, and even if the key is not in
the ignition switch.Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
When the hazard warning ashers are on, your
turn signals will not work.
Other Warning Devices
If you carry reective triangles, you can set them up
at the side of the road about 300 feet (100 m)
behind your vehicle.
Horn
To sound the horn, press the center pad on the
steering wheel.
138

Reducing Speed While Using Cruise
Control
If the cruise control system is already engaged,
Push and hold the SET– part of the button
until you reach the lower speed you want,
then release it.
To slow down in very small amounts, push the
SET– part of the button briey. Each time you
do this, the vehicle will go about 1 mph
(1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, the vehicle
will slow down to the cruise control speed you set
earlier.
Using Cruise Control on Hills
How well the cruise control will work on hills
depends upon the vehicle speed, load and the
steepness of the hills. When going up steep hills,
you may have to step on the accelerator pedal to
maintain the vehicle’s speed. When going downhill,
you may have to brake or shift to a lower gear to
keep the vehicle’s speed down. Of course, applying
the brake takes turns off the cruise control. Many
drivers nd this to be too much trouble and do not
use cruise control on steep hills.
Ending Cruise Control
To end cruise control, step lightly on the brake
pedal or the clutch pedal if the vehicle has
a manual transaxle.
Stepping on the brake pedal or clutch pedal will
only end the current cruise control session. Press
the cruise control on/off button to turn the system
completely off.
Erasing Speed Memory
When you turn off the cruise control or the
ignition, the cruise control set speed memory is
erased.
145

Headlamps
The lever on the left side of the steering column
operates the exterior lamps.
The exterior lamp switch has the following four
positions:
2(Headlamps):Turn the switch to this position
to turn on the headlamps, parking lamps, and
taillamps.
;(Parking Lamps):Turn the switch to this
position to turn on the parking lamps and
taillamps only.AUTO (Automatic Headlamp System):Turn the
switch to this position to automatically turn on the
Daytime Running Lamps (DRL) during daytime, and
the headlamps, parking lamps, and taillamps at
night. This position must be selected in order for the
Wiper Activated Headlamps to be activated. See
Wiper Activated Headlamps on page 147.
P(Off/On):This position is the momentary
Off/On switch for the Automatic Headlamp System.
For vehicles rst sold in Canada, the transaxle
must be in the PARK (P) position, before the
Automatic Headlamp System can be turned off.
When operating in AUTO, a momentary turn of the
switch to off/on will turn off the Automatic Headlamp
System. Rotating the switch to off/on again will turn
the Automatic Headlamp System back on. The
Automatic Headlamp System is always turned
on at the beginning of an ignition cycle.
146

Wiper Activated Headlamps
This feature activates the headlamps and parking
lamps after the windshield wipers are turned on.
For this feature to work, automatic lighting must
be enabled. SeeHeadlamps on page 146for
additional information.
When the ignition is turned off, the wiper-activated
headlamps will immediately turn off. They will also
turn off 15 seconds after the windshield wiper
control is turned off.
Headlamps on Reminder
If you open the driver’s door with the ignition off
and the lamps on, you will hear a warning chime.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.
Your vehicle has a light sensor on top of the
instrument panel. Make sure it is not covered or
the headlamps will come on when you do not
need them.
The DRL system will make the headlamps come on
at reduced intensity when the following conditions
are met:
The ignition is on.
The exterior lamp control is turned to AUTO.
The light sensor detects daytime light.
The shift lever is not in PARK (P).
While the DRL system is on, the taillamps,
sidemarker lamps, and instrument panel lights will
not be illuminated.
147