2007 NISSAN TIIDA ignition

AV
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
AV-43
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P Display Diagnosis
The tint of the color bar indication is as per the following list if RGB signal error is detected.
Vehicle Signals
A comparison check can be made of each actual vehicle signal and
the signals recognized by the system.
Sp ea ke r Tes t
JPNIA0169GB
R (red) signal error : Light blue (Cyan) tint
G (green) signal error : Purple (Magenta) tint
B (blue) signal error : Yellow tint
SKIB3663E
Diagnosis item Display Vehicle status Remarks
Vehicle speedON Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed by approximate-
ly 1.5 seconds. This is normal. OFF Vehicle speed = 0 km/h (0 MPH)
— Ignition switch ACC
Parking brakeON Parking brake is applied.
OFF Parking brake is released.
LightsON Light switch ON
—
OFF Light switch OFF
IgnitionON Ignition switch ON
—
OFF Ignition switch in ACC position
ReverseON Selector lever in R position
Changes in indication may be delayed by approximate-
ly 1.5 seconds. This is normal. OFFSelector lever in any position other
than R
— Ignition switch ACC

AV-44
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
Select “SPEAKER TEST” to display the Speaker Diagnosis screen.
Press “START and NEXT” to generate a test tone in a speaker.
Press “Start” to generate a test tone in the next speaker. Press
“Stop” to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Navigation
STEERING ANGLE ADJUSTMENT
The steering angle output value detected with the gyroscope is
adjusted.
SPEED CALIBRATION
During normal driving, distance error caused by tire wear and tire
pressure change is automatically adjusted for by the automatic dis-
tance correction function. This function, on the other hand, is for
immediate adjustment, in cases such as driving with tire chain fitted
on tires.
ERROR HISTORY
The diagnostic results of “Self-diagnosis” determine if any malfunction occurred between selecting “Self-diag-
nosis” and displaying “Self-diagnostic Results”.
The trouble diagnosis result will be judged normal if an error occurred before the ignition switch was turned
ON and does not occur again until “Self-diagnosis” is completed. Therefore, errors in the past which cannot be
found by “Self-diagnosis”, must be found by checking the “Error record”.
The error history shows the error occurrence frequency in past. The frequency of occurrence is displayed by 2
types: the count down type and the count up type. Select either type according to the error item.
In “Error History” of models with NAVI, time and place that the selected error last occurred are displayed. Be
careful about the following.
 The correct date of occurrence may not be able to be displayed if there is a malfunction with the GPS
antenna circuit board in the NAVI control unit.
 Place of the error occurrence is represented by the position of the current location mark at the time an error
occurred. If current location mark has deviated from the correct position, then the place of the error occur-
rence cannot be located correctly.Tweeter : 3 kHz
Front door speaker : 300 Hz
Rear door speaker : 1 kHz
SKIB4686E
SKIB3684E
SKIB3685E

AV
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
AV-45
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Transition Screen
Count Down Type
 Set the counter to 40 when the error is detected. The counter decreases by 1 if the system is normal when
turning the ignition switch ON.
 The lower limit of the counter is 1. It can be reset to 0 by “Delete log” switch or CONSULT-III.
Count Up Type The counter increases 1 when the ignition switch is turned ON and the error is detected. The counter does
not decrease even if it is normal when the ignition switch is turned ON the next time.
 The upper limit of the counter is 50. 51 or more is displayed as 50. It can be reset to 0 by “Delete log” switch
or CONSULT-III.
Error Item Some error items may be displayed simultaneously according to the cause. The detection of the cause can
be performed by the combination of display items if some error items are displayed simultaneously.
SKIB3687E
Display type of occur-
rence frequencyError history display item
Count down type CAN_COMM_CIRCUIT, CONTROL UNIT (CAN), AV COMM CIRCUIT, CONTROL UNIT (AV)
Count up type Other than the above
Error item Description Possible cause/Action to take
CAN_COMM_CIRCUITCAN communication malfunction is de-
tected.Perform the diagnosis using CONSULT-III,
and then repair the malfunctioning parts
based on diagnostic results.
Refer to AV- 4 8 , "
CONSULT - III Function
(MULTI AV)".
CONTROL UNIT (CAN) CAN initial diagnosis malfunction is de-
tected.NAVI control unit
CONTROL UNIT (AV) AV communication circuit initial diagno-
sis malfunction is detected. NAVI control unit
 AV COMM CIRCUIT
 Switches Connection Error
 Audio Unit Connection Error
 Amplifier Connection Error
 RDS-TMC Error Audio unit power supply and ground
circuit malfunction is detected.
 Malfunction is detected on communi-
cation circuit between Audio unit and
NAVI control unit.
 Malfunction is detected on communi-
cation signal between audio unit and
NAVI control unit. Audio unit power supply and ground cir-
cuit
 Communication circuit between audio
unit and NAVI control unit

AV-46
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
Vehicle CAN Diagnosis
 CAN communication status and error counter is displayed.
 Error counter displays 0 if any malfunction is not detected in the
past. It displays 40 if the malfunction is detected. It displays 39
when turning the ignition switch ON and it is normal. The lower
limit of the counter is 1.
 The error counter displays 0 if it resets.
NOTE:
“???” indicates UNKWN.
AV COMM Diagnosis
Front Display Connection Error Display unit power supply and
ground circuit malfunction is detect-
ed.
 Malfunction is detected on communi-
cation circuit between display unit
and NAVI control unit.
 Malfunction is detected on communi-
cation signal between display unit
and NAVI control unit. Display unit power supply and ground
circuit
 Communication circuit between display
unit and NAVI control unit
GPS Antenna ErrorGPS antenna connection malfunction
is detected. GPS antenna feeder
 GPS antenna
FLASH-ROM Error Of Control UnitNAVI control unit malfunction is detect-
ed.NAVI control unit
Connection Of GyroNAVI control unit malfunction is detect-
ed.NAVI control unit
GPS Communication Error
GPS malfunction is detected.Intermittent malfunction caused by strong
radio interference may be detected if the
symptoms such as the GPS receipt mal-
function occur.
Replace NAVI control unit if the malfunc-
tion always occurs. GPS ROM Error
GPS RAM Error
GPS RTC Error
DVD-ROM Communication Error
 Malfunction is detected on DVD-
ROM drive pickup lens in NAVI con-
trol unit.
 There is dirt and damage on the map
disc.Map disc
NAVI control unit DVD-ROM Read Error
DVD-ROM Disc Error
DVD-ROM Mechanism not Detected
DVD-ROM Mechanism Error
DVD-ROM Focus Error
DVD-ROM TOC Error
DVD-ROM Seek Error
DVD-ROM Error Correction Error
DVD-ROM Data Transfer Error
DVD-ROM Data Error
DVD-ROM Time-out
DVD-ROM Loading / Eject Error
CAN Controller Memory Error
NAVI control unit malfunction is detect-
ed.NAVI control unit
Bluetooth Module Connection ErrorError item Description Possible cause/Action to take
Items Display (Current)Malfunction counter
(Past)
Rx (ECM) OK / ??? 0 – 40
Rx (Cluster) OK / ??? 0 – 40
JPNIA0170GB

AV
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
AV-47
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 Displays the communication status between NAVI control unit
(master unit) and each unit.
 The error counter displays 0 if any malfunction was not detected in
the past. It displays 40 if the malfunction is detected. It displays 39
when turning the ignition switch ON and it is normal. The lower
limit of the counter is 1.
 The error counter is erased if it resets.
ITM: NAVI control unit
NOTE:
“???” indicates UNKWN.
Handsfree Phone
The hands-free phone reception volume adjustment, microphone
and speaker test, and memory erase functions are also available.
Bluetooth
Confirmation/Change Passkey
 The passkey of Bluetooth can be confirmed and changed.
 The passkey can be changed by four digits within 0 to 9.
Confirmation/Change Device Name
ItemsStatu s
(Current)Counter
(Past)
C Tx(ITM–PrimarySW) OK / ??? 0 – 40
C Rx(PrimarySW–ITM) OK / ??? 0 – 40
C Rx(STRG SW–ITM) OK / ??? 0 – 40
C Rx (Audio–ITM) OK / ??? 0 – 40
C Rx(Amp–ITM) OK / ??? 0 – 40
C Rx(RearCamera–ITM) OK / ??? 0 – 40
C Rx(XM–ITM) OK / ??? 0 – 40
C Rx(Amp–Audio) OK / ??? 0 – 40
C Tx(Audio–ITM) OK / ??? 0 – 40
SKIB4668E
SKIB3668E
SKIB3669E

AV-48
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
 The device name of Bluetooth can be confirmed and changed.
 The device name can be changed by sixteen digits within A to Z
(small character can be used) and - (hyphen).
Delete Unit Connection Log
Deletes any unit connection records and error records from the NAVI
control unit memory. (Clear the records of the unit that has been
removed.)
Feature Restriction Setting
Operations of navigation system that are performed while driving
can be restricted by using this function.
CAUTION:
Once operational restrictions are imposed, they can not be can-
celled even when the software is updated or the language-
switching program is loaded.
CONSULT - III Function (MULTI AV)INFOID:0000000001728644
CONSULT-III functions
CONSULT-III performs the following functions via the communication with the NAVI control unit.
Self-diagnosis results
 In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
 The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
 The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis results display item
JPNIA0171GB
JPNIA0172GB
JSNIA0345GB
Diagnosis mode Description
SELF-DIAG RESULTSPerforms a diagnosis on the NAVI control unit and a connection diagnosis for the communica-
tion circuit of the Multi AV system, and displays the current and past malfunctions collectively.
DATA MONITOR The diagnosis of vehicle signal that is input to the NAVI control unit can be performed.
AV COMM MONITOR Allows the technician to monitor the status of the Multi AV system communication signals.
ECU PART NUMBER The part number of NAVI control unit can be checked.

AV-50
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
ALL SIGNALS
 Displays the status of the following vehicle signals inputted to the NAVI control unit.
 For each signal, actual signal can be compared with the condition recognized on the system.
SELECTION FROM MENU
Allows the technician to select which vehicle signals should be displayed and displays the status of the
selected vehicle signals.
AV communication monitor
AV&NAVI C/U
 Displays the communication status from NAVI control unit to each unit as well as the error counter.
 The error counter displays “OK” if no malfunction was detected in the past and displays “0” if a malfunction is
detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of
the counter is 39.
AUDIO
 Displays the NAVI control unit communication status and the error counter.
Display ItemDis-
playVehicle status Remarks
VHCL SPD SIGON Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is
normal.
OFF Vehicle speed =0 km/h (0 MPH)
PKB SIGON Parking brake is applied.
Changes in indication may be delayed. This is
normal.
OFF Parking brake is released.
ILLUM SIGON Lighting switch ON
—
OFF Lighting switch OFF
IGN SIGON Ignition switch ON
—
OFF Ignition switch in ACC position
REV SIGON Selector lever in R position
Changes in indication may be delayed. This is
normal.
OFFSelector lever in any position other
than R
Item to be selected Description
VHCL SPD SIG
The same as when “ALL SIGNALS”
is selected. PKB SIG
ILLUM SIG
IGN SIG
REV SIG
Items Display (Current)Malfunction
counter
(Past)
TRANSMIT DIAG OK / UNKWN OK / 0 – 39
PANEL SWITCH OK/ UNKWN OK / 0 – 39
SW SECONDARY — —
RR CONTROL SW — —
STEERING SW OK / UNKWN OK / 0 – 39
AUDIO OK / UNKWN OK / 0 – 39
SPEAKER AMP OK / UNKWN OK / 0 – 39
FM MULTI OK / UNKWN OK / 0 – 39

AV
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
AV-51
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 The error counter displays “OK” if no malfunction was detected in the past and displays “0” if a malfunction is
detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of
the counter is 39.
ECU PART NUMBER
The part number of NAVI control unit is displayed.
Items Display (Current)Malfunction
counter
(Past)
TRANSMIT DG OK / UNKWN OK / 0 – 39