2007 NISSAN LATIO drain bolt

CYLINDER BLOCK
EM-81
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: June 20062007 Versa
19. Loosen main bearing cap bolts in reverse order as shown, and
remove them.
NOTE:
Before loosening main bearing cap bolts, measure crankshaft
end play. Refer to EM-95, "
CRANKSHAFT END PLAY" .
20. Remove main bearing caps.

Tap main bearing caps lightly using a suitable tool for
removal.
CAUTION:
Be careful not to damage the mounting surface.
21. Remove crankshaft.
CAUTION:

Be careful not to damage or deform signal plate (1)
mounted on rear end of crankshaft (A).

When setting crankshaft on a flat floor surface, use a
block of wood to avoid interference between signal plate
and the floor surface.

Never remove signal plate unless it is necessary to do so.
22. Pull rear oil seal out from rear end of crankshaft.
23. Remove main bearings and thrust bearings from cylinder block
and main bearing caps.
CAUTION:
Identify installation positions, and store them without mix-
ing them up.
ASSEMBLY
1. Fully air-blow engine coolant and engine oil passages in cylinder block, cylinder bore and crankcase to
remove any foreign material.
CAUTION:
Use a goggles to protect your eye.
2. Install water drain plug (1) to cylinder block.

Apply liquid gasket to the drain plug thread.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-46, "
Recommended Chemical Products and Sealants" .
3. Remove dust, dirt, and engine oil on the bearing mating sur-
faces of cylinder block and main bearing cap.
4. Install thrust bearings to the both sides of the No. 3 journal hous-
ing (B) on cylinder block.

Install thrust bearings with the oil groove (A) facing crankshaft
arm (outside).
: Engine front
PBIC3235J
PBIC3234J
: Engine front
9.8 N·m (1.0 kg-m, 87 in-lb)
PBIC3228J
: Engine front
PBIC3258J

MT-2
PRECAUTIONS
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ECS00GLL
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
PrecautionsUCS005LD

If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Installed CSC returns to the original position when removing transaxle assembly. Dust on clutch disc slid-
ing parts may damage CSC seal, and may cause clutch fluid leakage.

Do not reuse transaxle oil.

Drain, fill and check transaxle oil with the vehicle on level surface.

During removal or installation, keep inside of transaxle clear of dust or dirt.

Check for the correct installation orientation prior to removal or disassembly. If matching marks are
required, be certain they do not interfere with the function of the parts they are applied to.

In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If
tightening sequence is specified, follow it.

Be careful not to damage the sliding surfaces and mating surfaces of parts.

TRANSAXLE ASSEMBLY
MT-15
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
TRANSAXLE ASSEMBLYPFP:32010
Removal and InstallationUCS005LQ
CAUTION:
If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Inserted CSC returns to the original position when removing transaxle assembly. Dust on clutch disc
sliding parts may damage CSC seal, and may cause clutch fluid leakage.
COMPONENTS
REMOVAL
1. Drain gear oil. Refer to MT-9, "Changing M/T Oil" .
2. Drain clutch fluid and remove clutch tube from CSC. Refer to CL-9, "
Removal and Installation" .
CAUTION:
Do not depress clutch pedal during removal procedure.
3. Remove engine and transaxle assembly. Refer to EM-73, "
Removal and Installation" .
4. Remove starter motor. Refer to SC-23, "
Removal and Installation" .
5. Remove transaxle assembly to engine bolts.
6. Separate transaxle assembly from engine.
INSTALLATION
Installation is in the reverse order of removal.
1. LH engine mount bracket (transaxle
side)2. Transaxle assembly 3. Rear engine mount bracket
4. Washer 5. Rear torque rod⇐Front
: Refer to MT-15, "
INSTALLATION" for specification.
SCIA7631E

TRANSAXLE ASSEMBLY
MT-23
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
DISASSEMBLY
1. Remove drain plug and gasket from clutch housing, and drain oil.
2. Remove filler plug and gasket from transaxle case.
3. Remove CSC from clutch housing.
4. Remove retaining pin from shift lever (1) using a suitable tool.
5. Remove bracket (2) and position switch (3) from transaxle case.
6. Remove bolts.
7. Remove reverse idler shaft bolt ( ) and seal washer.
8. Remove transaxle case (1) upward while rotating control lever
(2).
PCIB1693E
PCIB1694E
PCIB1695E
PCIB1696E

TRANSAXLE ASSEMBLY
MT-33
D
E
F
G
H
I
J
K
L
MA
B
MT
Revision: June 20062007 Versa
29. Engage shift finger and selector by moving control lever (1).
Install transaxle case to clutch housing.
30. Install seal washer and reverse idler shaft bolt ( ), and then
tighten bolt to specification. Refer to MT-18, "
Gear Components"
.
CAUTION:
Do not reuse seal washer.
31. Tighten bolts to specification. Refer to MT-17, "
Case and Hous-
ing Components" .
32. Apply sealant to the threads of position switch (1). Then install it
into transaxle case and tighten to specification. Refer to MT-17,
"Case and Housing Components" .

Use Genuine Silicone RTV or equivalent. Refer to GI-XX,
"Recommended chemical products and sealants".
33. Install bracket (2), and tighten bolt to specification. Refer to MT-
17, "Case and Housing Components" .
34. Install shift lever (3), and then install retaining pin using a suit-
able tool.
CAUTION:
Do not reuse retaining pin.
35. Install CSC onto clutch housing. Refer to MT-17, "
Case and Housing Components" .
36. Install a new gasket onto drain plug, and then install it into clutch housing. Tighten drain plug to specifica-
tion. Refer to MT-17, "
Case and Housing Components" .
37. Install a new gasket onto filler plug, and then install it into transaxle case. Tighten filler plug to specifica-
tion. Refer to MT-17, "
Case and Housing Components" .
CAUTION:

Do not reuse gasket.

After oil is filled, tighten filler plug to specification. Refer to MT-17, "Case and Housing Compo-
nents"
SCIA7783E
PCIB1695E
PCIB1694E
SCIA7784E

MTC-64
A/C UNIT ASSEMBLY
Revision: June 20062007 Versa
A/C UNIT ASSEMBLYPFP:27110
Removal and InstallationEJS00583
REMOVAL
1. Use a recovery/recycling equipment (for HFC-134a) to discharge refrigerant.
2. Drain coolant from cooling system. Refer to CO-8, "
Changing Engine Coolant" .
3. Remove cowl top cover. Refer to EI-20, "
COWL TOP" .
4. Remove lower dash insulator.
5. Remove bolt (A), and then disconnect low-pressure flexible
hose (1) and high-pressure pipe (2) from evaporator.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
6. Remove clamps (A), and then disconnect heater hoses (1) from
heater core.
7. Remove console box assembly. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
A. A/C unit assembly bolts B. Steering member bolts C. Steering column nuts
SJIA0648E
SJIA0644E
SJIA0645E

RF-24
SUNROOF
Revision: June 20062007 Versa
SUNROOF UNIT ASSEMBLY
Removal
1. Tilt glass lid up, then remove. Refer to RF-25, "GLASS LID" .
2. Position sunroof unit assembly to the fully closed position.
3. Remove the headlining. Refer to EI-39, "
HEADLINING" .
4. Disconnect drain hoses.
5. Remove the screws, then disconnect the sunroof motor assem-
bly.
NOTE:

Before removing sunroof motor assembly, make sure that
sunroof is fully closed.

After removing sunroof motor assembly, do not attempt to
rotate sunroof motor as a single unit.
6. Remove the side and front sunroof unit assembly nuts.
7. Remove sunroof bracket bolts, then remove sunroof unit assem-
bly from roof panel.

Remove sunroof unit assembly through the passenger com-
partment.
CAUTION:
Use care during assembly removal and installation to avoid
damage to seats and trim.
Installation
1. Install sunroof brackets and bolts to the roof panel side only, but
do not tighten.
2. Bring sunroof unit assembly into passenger compartment and
position it so the rear rests on the sunroof brackets.
3. Install sunroof bracket bolts to the sunroof unit assembly side,
but do not tighten.
7. Sunroof unit assembly 8. Sunroof motor assembly 9. Sunshade
10. Sunshade stopper 11. Link assembly (LH)⇐Vehicle front
PIIB4745J
PIIB4747J
PIIB4748J
PIIB4748J

SUNROOF
RF-25
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: June 20062007 Versa
4. Install the front and side sunroof unit assembly nuts, but do not
tighten.
5. Tighten the sunroof unit assembly.
a. First, tighten the sunroof bracket bolts at the vehicle side, then
tighten the bolt on the rail side.
b. Next, tighten the front and side sunroof unit assembly nuts diag-
onally.
6.7. Connect the sunroof motor assembly connector and install the
screws.
8. Install the glass lid. Refer to RF-25, "
GLASS LID" .
9. Connect drain hoses.
10. Install headlining. Refer to EI-39, "
HEADLINING" .
11. Perform fitting adjustment and test for leaks, refer to RF-28, "
Fitting Adjustment" .
GLASS LID
Removal
1. Open the sunshade fully and close the glass lid.
2. Remove glass lid bolts, then remove glass lid.
Installation
1. Position the glass lid on sunroof unit assembly.
PIIB4746J
PIIB4748J
PIIB4745J
PIIB4749J