INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: 2006 November2007 350Z
Removal and InstallationNIS00099
WORK STEP
When removing instrument panel, combination meter, audio and console assembly, take steps in the order
shown by the numbers below.
CAUTION:
Disconnect both battery cables in advance.
Disconnect air bag system line in advance.
Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
Be careful not to scratch pad and other parts.
1. Instrument panel 2. Instrument side finisher (LH) 3. Instrument driver panel upper
4. Combination meter 5. Instrument driver panel lower 6. Steering column cover
7. Steering lock escutcheon 8. Fuse cover 9. Dash side finisher (LH)
10. Unified meter and A/C amp. 11. Foot rest plate 12. Foot rest
13. Center console 14. Console boot (M/T) 15. Cluster lid C lower
16. Console finisher (A/T) 17. Console finisher (A/T ring) 18. Dash side finisher (RH)
19. Instrument side panel (RH) 20. Instrument side panel (LH) 21. Audio unit
22. Instrument passenger panel lower 23. Knee protector (RH) 24. Cluster lid C
25. NAVI switch 26. Instrument center panel 27. Instrument finisher (LH/RH)
28. Pocket mat 29. Instrument passenger panel upper 30. Instrument side finisher (RH)
31. Knee protector (LH)
Pawl Clip Metal clip
PartsReference
pageInstrument
panelCombination
meterAudio Center console
(A) Kicking plate (RH / LH)EI-35
[ 1 ] [ 1 ]
(B) Foot restEI-43
[ 2 ] [ 2 ]
(C) Dash side finisher (RH / LH)EI-35
[ 3 ] [ 3 ]
(D) Instrument driver panel lowerIP-12
[ 4 ] [ 4 ]
(E) Steering column lower coverIP-12
[ 5 ] [ 5 ]
(F) Combination meterIP-12
[ 6 ] [ 6 ]
(G) Spiral cableSRS-42
[ 7 ]
(H) Console finisher (A/T Models)IP-13
[ 8 ] [ 1 ] [ 1 ]
(I) Cluster lid C lower (A/T Models)IP-13
[ 8 ] [ 1 ] [ 1 ]
(J) Console boot (M/T Models)IP-13
[ 8 ] [ 1 ] [ 1 ]
(K)
Center console *
1IP-13[10] [ 2 ]
(L) Instrument passenger panel lowerIP-13
[11]
(M) Instrument side panel (RH / LH)IP-13
[12]
(N) Unified meter and A/C amp.IP-13
[13] [ 2 ]
(O)Instrument center panel (with NAVI
models)IP-14
[14] [ 3 ]
(P) NAVI switch (with NAVI models)IP-14
[15] [ 4 ]
(Q)
Cluster lid C*
2IP-14[16] [ 5 ]
(R) Display unit (with NAVI models)IP-14
[17]
(S) Front pillar garnish (RH / LH)EI-36
[18]
(T) Instrument driver panel upperIP-14
[19]
(U) Instrument passenger panel upperIP-14
[20]
(V) Instrument side finisher (RH)IP-14
[21]
(V) Instrument panel IP-15
[22]
INSTRUMENT PANEL ASSEMBLY
IP-13
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: 2006 November2007 350Z
(H) Console Finisher (A/T Models)
1. Insert a thin flat-bladed screwdriver wrapped with tape from
behind console finisher, and remove metal clip on back. Then
pull up and back to disengage from front metal clip.
2. Disconnect harness connector, and remove console finisher.
NOTE:
A/C controller is assembled in the console finisher. Therefore, when
installing and removing be careful not to use excessive force, etc.
(I) Cluster lid C lower (A/T Models)
1. Disconnect harness connector.
2. Remove metal clips and pawls, and remove cluster lid C lower.
(J) Console Boot (M/T Models)
1. Remove metal clip.
2. Remove shift knob. Refer to MT-12, "
Removal and Installation" .
3. Disconnect harness connector, and remove console boot.
NOTE:
A/C controller is assembled in the console boot. Therefore, when
installing and removing be careful not to use excessive force, etc.
(K) Center Console
1. Remove coin holder and ashtray.
2. Remove screws.
3. Remove console sub-harness.
4. After removing, disassemble each parts. Refer to IP-16, "
CENTER CONSOLE" .
NOTE:
When removing console, be careful not to pull the harness.
(L) Instrument Passenger Panel Lower
1. Remove screws and bolt.
2. Pull panel horizontally toward you and disengage from metal clip.
(M) Instrument Side Panel (RH/LH)
1. Remove screws.
2. Pull to the side, disconnect metal clips, and remove instrument side panel.
(N) Unified Meter And A/C Amp.
Remove screws, and disconnect harness connector, and remove unified meter and A/C amp. Refer to AT C -
103, "AUTO AMP" .
PIIB7174J
PIIB7175J
PIIB7386J
