2007 NISSAN 350Z lock

FRONT DOOR GLASS AND REGULATOR
GW-53
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
1. With the door open, lift up and hold the power window switch until the door glass is fully closed.
2. Get inside the vehicle and close the door.
NOTE:
You need to close the door so the door switch is fully depressed.
3. Press and hold the reset switch. While holding the reset switch, press down and hold the power window
switch until the door glass is fully opened.
4. Relese the reset switch.Then, lift up and hold the power window
switch until the door glass is fully closed.
5. Open the door to release the door switch. The door glass should
partially move down.
CAUTION:

Do not use the window auto function.

Do not release the switch before the window is fully
stopped.
FITTING INSPECTION

Check that glass is securely fit into glass run groove.

Lower glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)] and check the distance between the edge of
glass and the body side welt. If the distance is not constant, adjust the glass position by loosening and
tightening following bolts.
–Regulator mounting bolt and nut
–Glass and guide rail mounting bolt

Raise the glass fully and adjust the glass top end and body side
welt fitting with the adjusting bolt at the lower of the regulator
rear rail.
NOTE:

Turn the adjusting bolt clockwise to move the door glass
upper end outward.

Turn the adjusting bolt counterclockwise to move the door
glass upper end inward.

If water leaks, repair the fitting (Roadster only). Refer to RF-
11 6 , "Repairing Method for Water Leakage Around Doors" .
SIIA0347E
PIIA7672E

GW-56
REAR WINDOW DEFOGGER
Revision: 2006 November2007 350Z
REAR WINDOW DEFOGGERPFP:25350
Component Parts and Harness Connector LocationNIS0005C
System DescriptionNIS0005D
The rear window defogger system is controlled by BCM (Body Control Module) and IPDM E/R (Intelligent
Power Distribution Module Engine Room). The rear window defogger operates only for approximately 15 min-
utes.
Power is supplied at all times

through 20A fuse [No. 75 and 80, located in the IPDM E/R]

to rear window defogger relay terminal 3 and 6.

through 40A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55.

through 10A fuse [No. 18, located in the fuse block (J/B)]

to BCM terminal 42.

through 10A fuse [No. 19, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 21.
With the ignition switch turned to ON or START position, power is supplied

through 10A fuse [No. 1, located in the fuse block (J/B)]

to BCM terminal 38.

through 10A fuse [No. 12, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 22 and rear window defogger relay terminal 1

and then through unified meter and A/C amp.

to A/C controller (rear window defogger switch) terminal 72 and 84.
PIIB3830E

REAR WINDOW DEFOGGER
GW-57
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
Ground is supplied

to BCM terminal 52

through body grounds M30, and M66.

to unified meter and A/C amp. terminal 29 and 30

through body grounds M30 and M66.

to internal CPU of IPDM E/R terminal 38 and 60

through body grounds E17, E43, B102 (with VDC system or navigation system) and F152 (without VDC
system and navigation system).
When A/C controller (rear window defogger switch) is turned ON,
Rear window defogger switch signals are transmitted,

through A/C controller terminal 87

to unified meter and A/C amp.
Then ground is supplied

to BCM terminal 9

through unified meter and A/C amp. terminal 38

through unified meter and A/C amp. terminal 30

through body grounds M30 and M66.
Then BCM recognizes that rear window defogger switch is turned ON.
Then it sends rear window defogger switch signals to IPDM E/R via DATA LINE (CAN H, CAN L).
When IPDM E/R receives rear window defogger switch signals,
Ground is supplied

to rear window defogger relay terminal 2

through IPDM E/R terminal 52

through internal CPU of IPDM E/R

through IPDM E/R terminal 60

through body grounds E17, E43, B102 (with VDC system or navigation system), F152 (without VDC sys-
tem and navigation system), and then rear window defogger relay is energized.
When rear window defogger relay is turned ON,
Signals are transmitted

to rear window defogger terminal 1

through rear window defogger relay terminals 5 and 7 (For Coupe)

through rear window defogger relay terminal 5. (For Roadster)
Rear window defogger terminal 2 is grounded through body ground D212. (For Coupe)
Rear window defogger terminal 2 is grounded through body ground B5, B6 and T14. (For Roadster)
With power and ground supplied, rear window defogger filaments heat and defog the rear window.
When rear window defogger relay is turned ON,
Power is supplied

through rear window defogger relay terminals 5 and 7 (For Coupe)

through rear window defogger relay terminal 7 (For Roadster)

through fuse block (J/B) terminal 2C

through 10A fuse [No. 8, located in the fuse block (J/B)]

through fuse block (J/B) terminal 5B

to door mirror defogger (Driver side and passenger side) terminal 2.
Door mirror defogger (Driver side and passenger side) terminal 1 is grounded through body grounds M30 and
M66.
With power and ground supplied, door mirror defogger filaments heat and defog the mirror.
When rear window defogger relay is turned ON,
Power is supplied

through rear window defogger relay terminals 5 and 7 (For Coupe)

through rear window defogger relay terminal 5. (For Roadster)

to unified meter and A/C amp. terminal 56
Then ground is supplied

REAR WINDOW DEFOGGER
GW-71
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M90 terminal 9 and
ground.
OK or NG
OK >> Replace unified meter and A/C amp.
NG >> Replace BCM.
Check Rear Window Defogger Power Supply CircuitNIS0005T
1. CHECK FUSE
Check 10A fuse [No. 12, located in fuse block (J/B)].
NOTE:
Refer to GW-56, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT INSPECTION
1. Turn ignition switch OFF.
2. Remove rear window defogger relay.
3. Check voltage between rear window defogger relay connector
B34 terminal 1 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.9 (L/R) – Ground :Approx. 5V
PIIA6208E
1 (G/R) – Ground : Battery voltage
PIIA2377E

REAR WINDOW DEFOGGER
GW-75
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
Check Door Mirror Defogger Power Supply CircuitNIS0005W
1. CHECK FUSE

Check 10A fuse [No. 8, located in fuse block (J/B)].
NOTE:
Refer to GW-56, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT INSPECTION 1
1. Turn ignition switch ON.
2. Rear window defogger switch operate, check voltage between
fuse block (J/B) connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace between harness.
3. DOOR MIRROR DEFOGGER POWER SUPPLY INSPECTION 2
Rear window defogger switch operate, check voltage between Fuse
block (J/B) connector and ground.
OK or NG
OK >> Repair or replace harness.
NG >> Replace fuse block (J/B).
ConnectorTerminal
(Wire color)
ConditionVoltage [V]
(Approx.)
(+) (–)
E101 2C (Y) GroundRear window
defogger switch: ON Battery voltage
: OFF 0
PIIA2388E
ConnectorTerminal
(Wire color)
ConditionVoltage [V]
(Approx.)
(+) (–)
M5 5B (L) GroundRear window
defogger switch: ON Battery voltage
: OFF 0
PIIA2386E