2007 NISSAN 350Z wheel

GI-2Revision: 2006 November2007 350Z ENGINE SERIAL NUMBER ................................ 48
AUTOMATIC TRANSMISSION NUMBER ........... 48
MANUAL TRANSMISSION NUMBER ................. 48Dimensions ............................................................. 49
Wheels & Tires ........................................................ 49
TERMINOLOGY ........................................................ 50
SAE J1930 Terminology List ................................... 50

GI-4
PRECAUTIONS
Revision: 2006 November2007 350Z

Before jacking up the vehicle, apply wheel chocks or other tire
blocks to the wheels to prevent the vehicle from moving. After
jacking up the vehicle, support the vehicle weight with safety
stands at the points designated for proper lifting before working
on the vehicle.
These operations should be done on a level surface.

When removing a heavy component such as the engine or tran-
saxle/transmission, be careful not to lose your balance and drop
them. Also, do not allow them to strike adjacent parts, especially
the brake tubes and master cylinder.

Before starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.

If the battery terminals are disconnected, recorded memory of
radio and each control unit is erased.

Battery posts, terminals and related accessories contain lead
and lead compounds. Wash hands after handling.

To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.

Dispose of or recycle drained oil or the solvent used for cleaning
parts in an appropriate manner.

Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel
spray and possibly a fire.

Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.

Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. with new
ones.

Replace inner and outer races of tapered roller bearings and needle bearings as a set.

Arrange the disassembled parts in accordance with their assembled locations and sequence.

Do not touch the terminals of electrical components which use microcomputers (such as ECM).
Static electricity may damage internal electronic components.

After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.

Use only the fluids and lubricants specified in this manual.

Use approved bonding agent, sealants or their equivalents when required.

Use hand tools, power tools (disassembly only) and recom-
mended special tools where specified for safe and efficient ser-
vice repairs.

When repairing the fuel, oil, water, vacuum or exhaust systems,
check all affected lines for leaks.
SGI231
SEF289H
SGI233
PBIC0190E

HOW TO USE THIS MANUAL
GI-23
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: 2006 November2007 350Z
AbbreviationsNAS0000K
The following ABBREVIATIONS are used:
ABBREVIATION DESCRIPTION
A/C Air Conditioner
A/T Automatic Transaxle/Transmission
ATF Automatic Transmission Fluid
D
1Drive range 1st gear
D
2Drive range 2nd gear
D
3Drive range 3rd gear
D
4Drive range 4th gear
FR, RR Front, Rear
LH, RH Left-Hand, Right-Hand
M/T Manual Transaxle/Transmission
OD Overdrive
P/S Power Steering
SAE Society of Automotive Engineers, Inc.
SDS Service Data and Specifications
SST Special Service Tools
2WD 2-Wheel Drive
2
22nd range 2nd gear
2
12nd range 1st gear
1
21st range 2nd gear
1
11st range 1st gear

LIFTING POINT
GI-39
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: 2006 November2007 350Z
LIFTING POINTPFP:00000
Commercial Service Tools NAS0000U
CAUTION:

Every time the vehicle is lifted up, maintain the complete vehicle curb condition.

Since the vehicle's center of gravity changes when removing main parts on the front side (engine,
transmission, suspension etc.), support a jack up point on the rear side garage jack with a mission
jack or equivalent.

Since the vehicle's center of gravity changes when removing main parts on the rear side (rear axle,
suspension, etc.), support a jack up point on the front side garage jack with a mission jack or
equivalent.

Be careful not to smash or do not do anything that would affect piping parts.
Garage Jack and Safety Stand NAS0000V
WARNING:

Park the vehicle on a level surface when using the jack. Make sure to avoid damaging pipes,
tubes, etc. under the vehicle.

Never get under the vehicle while it is supported only by the jack. Always use safety stands when
you have to get under the vehicle.

Place wheel chocks at both front and back of the wheels on the ground.
Tool name Description
Board on attachment
Safety stand attachment
S-NT001
S-NT002

GI-42
TOW TRUCK TOWING
Revision: 2006 November2007 350Z
TOW TRUCK TOWINGPFP:00000
Tow Truck TowingNAS0000Y
CAUTION:


All applicable state or Provincial (in Canada) laws and local
laws regarding the towing operation must be obeyed.

It is necessary to use proper towing equipment to avoid
possible damage to the vehicle during towing operation.
Towing is in accordance with Towing Procedure Manual at
dealer.

Always attach safety chains before towing.

When towing, make sure that the transmission, steering
system and power train are in good order. If any unit is
damaged, dollies must be used.
NISSAN recommends that the vehicle be towed with the driving
(rear) wheels off the ground as illustrated.
CAUTION:

Never tow an automatic transmission model with the rear
wheels or four wheels on the ground (forward or backward).
This may cause serious and expensive damage to the
transmission.

When towing with the front wheels on the ground (if you do
not use towing dollies), turn the ignition key to the OFF
position, and secure the steering wheel in the straight-
ahead position with a rope or similar device. Never place
the ignition key in the LOCK position. This will result in
damage to the steering lock mechanism.

When towing a manual transmission model with the rear
wheels on the ground (if you do not use towing dollies),
release the parking brake and move the shift lever to the N
(Neutral) position.
SGI994
PAIA0063E

TOW TRUCK TOWING
GI-43
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: 2006 November2007 350Z
Vehicle Recovery (Freeing a Stuck Vehicle) NAS0000Z
FRONT
After removing the front licence plate (if so equipped),
1 Remove the recovery hook cover from the bumper.
2 Securely install the recovery hook stored with jacking tools.
Make sure that the hook is properly secured in the stored place after
use.
WARNING:

Stand clear of a stuck vehicle.

Do not spin your tires at high speed. This could cause them
to explode and result in serious injury. Parts of your vehicle
could also overheat and be damaged.
CAUTION:

Tow chains or cables must be attached only to the vehicle recovery hooks or main structural mem-
bers of the vehicle. Otherwise, the vehicle body will be damaged.

Do not use the vehicle tie downs to free a vehicle stuck in sand, snow, mud, etc. Never tow a vehi-
cle using the vehicle tie downs or recovery hooks.

Always pull the cable straight out from the front of the vehicle. Never pull on the vehicle at an
angle.

Pulling devices should be routed so they do not touch any part of the suspension, steering, brake
or cooling systems.

Pull devices such as ropes or canvas straps are not recommended for use in vehicle towing or
recovery.
If your vehicle is stuck in sand, snow, mad, etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control System (if so equipped).
2. Make sure the area in front and behind the vehicle is clear of obstructions.
3. Turn the steering wheel right and left to clear an area around front tires.
4. Slowly rock the vehicle forward and backward.

Shift back and forth between R (reverse) and D (drive) (automatic transmission models) or 1st (low)
and R (reverse) (manual transmission models).

Apply the accelerator as little as possible to maintain the rocking motion.

Release the accelerator pedal before shifting between R and D (automatic transmission models) or 1st
and R (manual transmission models).

Do not spin the tires above 35 MPH (55 km/h).
5. If the vehicle cannot be freed after a few tires, contact a professional towing service to remove the vehicle.
REAR

Towing hook is not available.
PAIA0064E

IDENTIFICATION INFORMATION
GI-49
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: 2006 November2007 350Z
Dimensions NAS00013
Unit: mm (in)
*1: For model with 245/45R18 tires
*2: For model with 265/35R19 tires
Wheels & Tires NAS00014
Model Coupe Roadster
Overall length 4,314 (169.8) 4,314 (169.8)
Overall width 1,815 (71.5) 1,815 (71.5)
Overall height 1,323 (52.1) 1,333 (52.5)
Front tread 1,536 (60.5) 1,536 (60.5)
Rear tread 1,540 (60.6)*1, 1,546 (60.9)*2 1,540 (60.6)
Wheelbase 2,650 (104.3) 2,650 (104.3)
Road wheelType Size Offset mm (in)
AluminumFront18 x 8JJ
30 (1.18)
18 x 9 JJ
Rear18 x 8-1/2JJ 33 (1.30)
19 x 10JJ 30 (1.18)
Spare 17 x 4T 30 (1.18)
TireConventionalFront225/45R18 91W
245/40R18 93W*
Rear245/45R18 96W
265/35R19 94W*
Spare T145/80D17 107M