2007 MERCEDES-BENZ SLK55AMG adding oil

297 Operation
Engine compartment
One of the following messages will
subsequently appear in the multifunc-
tion display:

Engine oil level
OK

Add 1.0 qt. (Canada: 1.0 liter)
to reach max. oil level

Add 1.5 qts. (Canada:
1.5 liters)
to reach max. oil level

Add 2.0 qts. (Canada:
2.0 liters)
to reach max. oil level
If necessary, add engine oil.
For adding engine oil, see “Adding
engine oil” (
page 299).
For more information on engine oil, see
“Fuels, coolants, lubricants, etc.”
(
page 443).Other display messages
If the ignition is not switched on, the fol-
lowing message will appear:
Turn on ignition
to see engine oil level
Switch on the ignition (page 37).
If you see the message:
Observe waiting time
If engine is at operating temperature,
wait 5 minutes before repeating check
procedure.
If engine is not at operating tempera-
ture yet, you must wait 30 minutes
before checking oil.If you see the message:
Cannot check engine
level with engine on
Turn off the engine.
If the engine is at operating tempera-
ture, wait 5 minutes before checking
oil.
If the engine is not at operating
temperature yet, you must wait
30 minutes before checking oil.
iIf you want to interrupt the checking
procedure, press buttonk orj on the
multifunction steering wheel (
page 122).
iIf you want to interrupt the checking
procedure, press buttonk orj on the
multifunction steering wheel (
page 122).

299 Operation
Engine compartment
Pull out oil dipstick1 again after
approximately 3 seconds to obtain
accurate reading.
The oil level is correct when it is be-
tween the lower (min) mark3 and
upper (max) mark2 of oil dipstick1.
If necessary, add engine oil.
For adding engine oil, see “Adding
engine oil” (
page 299).
For more information on engine oil, see
“Fuels, coolants, lubricants, etc.”
(
page 443).
For more information on messages in the
multifunction display concerning engine
oil, see the “Practical hints” section
(
page 356).Adding engine oil
Only use approved engine oils and oil fil-
ters required for vehicles with
Maintenance System. For a listing of
approved engine oils and oil filters, refer to
the Factory Approved Service Products
pamphlet (USA only) in your vehicle litera-
ture portfolio, or contact an authorized
Mercedes-Benz Center.
Using engine oils and oil filters of
specification other than those expressly
required for the Maintenance System, or
changing of oil and oil filter at change inter-
vals longer than those called for by the
Maintenance System will result in engine
or emission control system damage not
covered by the Mercedes-Benz Limited
Warranty.
SLK 350 (example illustration)
1Filler cap
SLK 55 AMG
1Filler cap
iThe filling quantity between the upper and
lower marks on the oil dipstick is approximately
2.1 US qt. (2.0 l).

300 Operation
Engine compartment
Unscrew filler cap1 from filler neck.
Add engine oil as required.
Be careful not to overfill with oil.
Be careful not to spill any oil when adding.
Avoid environmental damage caused by oil
entering the ground or water.
Screw filler cap1 back on filler neck.
For more information on engine oil, see
“Technical data” (
page 443) and
(
page 445).
Transmission fluid level*
Vehicles with automatic transmission*:
The transmission fluid level does not need
to be checked. If you notice transmission
fluid loss or gear shifting malfunctions,
have an authorized Mercedes-Benz Center
check the transmission.Coolant level
The engine coolant is a mixture of water
and anticorrosion/antifreeze. To check
the coolant level, the vehicle must be
parked on level ground and the engine
must be cool.
!Excess oil must be siphoned or drained off.
It could cause damage to the engine and
emission control system not covered by the
Mercedes-Benz Limited Warranty.Warning!G
In order to avoid any potentially serious
burns:

Use extreme caution when opening the
hood if there are any signs of steam or
coolant leaking from the cooling system,
or if the coolant temperature gauge indi-
cates that the coolant is overheated.

Do not remove pressure cap on coolant
reservoir if coolant temperature is
above 158°F (70°C). Allow engine to
cool down before removing cap. The
coolant reservoir contains hot fluid and
is under pressure.

448 Technical data
Fuels, coolants, lubricants, etc.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which pro-
vides:

Corrosion protection

Freeze protection

Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.
If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Center.To provide important corrosion protection,
the solution must be at least
50% anticorrosion/antifreeze (equivalent
to freeze protection to approximately
-35°F [-37°C]). If you use a solution that is
more than 55% anticorrosion/antifreeze
(freeze protection to approximately
-49°F [-45°C]), the engine temperature
will increase due to the lower heat transfer
capability of the solution. Therefore, do not
use more than this amount of anticorro-
sion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label
instructions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
tact an authorized Mercedes-Benz Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the Mercedes-Benz
Limited Warranty.

456 Index
E
Easy-entry/exit feature* 44, 147
Electric air pump
Inflating collapsible tire 411
Sealing tires with TIREFIT 401
Vehicle tool kit 382
Electrical system (Technical data) 440
Electronic Stability Program see ESP
®
Emergency call (911) 233
Emergency call system 262
Tele Aid* 263
Emergency operations
Automatic transmission* (Limp-Home
Mode) 167
Remote door unlock, Tele Aid* 269
Retractable hardtop 390
Selector lever*, unlocking
manually 389
Trunk lid, Releasing from the
inside 101
Unlocking/locking the vehicle 387Emergency Tensioning Device see ETD
Emission control 289
Information label 431
System warranties 10
Vacuum line routing diagram 431
Engine
Cleaning 339
Compartment 294
Malfunction indicator lamp 27, 349
Number 431
Poly-V-belt layout 432
Starting 51
Tachometer 119
Technical data 433
Turning off 61Engine oil 296, 445
Adding 299
Additives 445
Checking level (Control system) 296
Checking level (Dipstick) 298
Consumption 296
Messages in the multifunction
display 297, 372–373
ESP®84, 86
Messages in the multifunction
display 358, 359
Warning lamp 350
ETD 79
Safety guidelines 68
Warning and indicator lamps 353
Exterior lamp switch 109
Exterior lighting
Lamps 393
Replacing bulbs 393
Exterior rear view mirrors see Mirrors