2007 MERCEDES-BENZ SL600 key battery

110 Controls in detailLocking and unlockingGlobal locking using the lock button on
the trunk lid
1Lock button

Press lock button 1 on the trunk lid.
With the trunk and all doors closed, all
turn signals flash three times. The lock-
ing knobs in the doors move down.
The anti-theft alarm system is armed.
Checking the batteries

Press button ‹or Œ.
Battery check lamp5 (
page 106)
comes on briefly to indicate that the
SmartKey batteries are in order.Loss of SmartKey with KEYLESS-GO
If you lose your SmartKey with
KEYLESS-GO, you should do the following:

Have the SmartKey with KEYLESS-GO
deactivated by an authorized
Mercedes-Benz Center.

Report the loss of the SmartKey with
KEYLESS-GO or the mechanical key to
your car insurance company immedi-
ately.

Have the mechanical lock replaced if
necessary.
Your authorized Mercedes-Benz Center
will be glad to supply you with a replace-
ment.
i
Vehicles with KEYLESS-GO*: To prevent a
possible inadvertent lockout, the trunk lid will
open automatically if a SmartKey with
KEYLESS-GO is recognized inside the trunk.
When the hardtop is retracted, it must be com-
pletely lowered in the trunk before the trunk lid
can be closed (
page 242).
i
You can also lock the vehicle using the lock
button on an outside door handle (
page 64).
i
If battery check lamp5 (
page 106) does
not come on briefly during check, then the
SmartKey batteries are discharged.


Replace the batteries (
page 395).
You can obtain the required batteries at any
authorized Mercedes-Benz Center.
i
If the batteries are checked within signal
range of the vehicle, pressing the‹orŒ
button will lock or unlock the vehicle according-
ly.

198 Controls in detailPower windowsFully closing the door windows
(Express-close)
Pull switch1 or2 past the resis-
tance point and release.
The corresponding door window closes
completely.
If the upward movement of the door win-
dow is blocked during the closing proce-
dure, the door window will stop and open
slightly.
Stopping windows

Press or pull the respective switch
again.Closing the windows with
KEYLESS-GO*

Press and hold lock button on an out-
side door handle (
page 64) until the
windows are closed.
Synchronizing power windows
The power window must be synchronized
each time

after the battery has been disconnect-
ed


if the power windows cannot be fully
opened (Express-open) or closed
(Express-close)
Synchronizing the power windows

Switch on the ignition (
page 39).

Pull the power window switches until
the side windows are closed.
Hold the switches for approximately
1 second.
The power windows are synchronized.
Warning!
G
Driver’s door only:
If within 5 seconds the switch is again
pulled past the resistance point and re-
leased, the automatic reversal will not
operate.
Warning!
G
When closing the windows make sure that
there is no danger of anyone being harmed
by the closing procedure.
The windows will not automatically re-open
if blocked during convenience closing.
If potential danger exists, proceed as fol-
lows:

Release the lock button.


Pull on the door handle and hold firmly.
The side windows open for as long as
the door handle is held but the door not
opened.

379 Practical hints
What to do if …
Left display
Right display
Possible cause/consequence
Possible solution
F
Key
not detected
The SmartKey with KEYLESS-GO* is
not recognized while the engine is
running because:

The SmartKey with
KEYLESS-GO* is not in the vehi-
cle.


There is strong radio-frequency
interference.

Stop the vehicle in a safe location or as soon
as it is safe to do so.

Search for the SmartKey with KEYLESS-GO*.
Otherwise the vehicle cannot be centrally
locked nor can the engine be started again af-
ter the engine is stopped.

Operate the vehicle with the SmartKey with
KEYLESS-GO* in the starter switch
Key
not detected
The SmartKey with KEYLESS-GO* is
not recognized when attempting to
start the engine with the
KEYLESS-GO start/stop button* on
the gear selector lever because:

The SmartKey with
KEYLESS-GO* is not in the vehi-
cle.


The battery in the SmartKey
with KEYLESS-GO* is not insert-
ed properly or completely dis-
charged.

Change the position of the SmartKey with
KEYLESS-GO* in the vehicle.

Make sure the batteries in the SmartKey with
KEYLESS-GO* are properly inserted
(page 395) and are not discharged
(page 110).

Start the engine with the SmartKey with
KEYLESS-GO* in the starter switch if
necessary.

395 Practical hints
Replacing SmartKey batteries
Replacing SmartKey batteries
If the batteries in the SmartKey or the
SmartKey with KEYLESS-GO* are dis-
charged, the vehicle can no longer be
locked or unlocked. It is recommended to
have the batteries replaced at an autho-
rized Mercedes-Benz Center.Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.

Remove the mechanical key from the
SmartKey or SmartKey with
KEYLESS-GO* (
page 391).
1Mechanical key
2Battery compartment

Insert mechanical key 1 into opening.

Press mechanical key 1 in direction of
arrow.
The battery compartment is unlatched.

Pull battery compartment 2 out of the
housing.
Warning!
G
Batteries contain poisonous and corrosive
substances. Therefore keep the batteries
out of reach of children.
If a battery is swallowed, seek medical help
immediately.
i
When inserting batteries, make sure they
are clean and free of lint.
i
When replacing batteries, always replace
both batteries.
The required replacement batteries (Lithium,
type CR 2025 or equivalent) are available at any
authorized Mercedes-Benz Center.


396 Practical hintsReplacing SmartKey batteries3Batteries
4Contact spring
Pull out batteries3.

Using a lint-free cloth, insert new bat-
teries 3 under contact springs 4 with
the positive terminal (+) side facing up.

Return battery compartment 2 into
housing until it locks into place.

Slide mechanical key 1 back into
SmartKey or SmartKey with
KEYLESS-GO*.

Check the operation of the SmartKey
or SmartKey with KEYLESS-GO* as well
as the KEYLESS-GO* function.


415 Practical hints
Batteries
!
The factory-equipped VRLA battery is
leak-proofed. Only use a battery as replacement
that has the same security features and is of
identical size, voltage, and capacity as the
factory-equipped battery.
The battery, the battery ventilation and the later-
al plug must always be securely installed when
the vehicle is in operation.
Warning!
G
Failure to follow these instructions can re-
sult in severe injury or death.
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
!
Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the starter battery checked regularly by an
authorized Mercedes-Benz Center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized
Mercedes-Benz Center for further information.
Warning!
G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof batteries only to avoid the
risk of acid burns in the event of an acci-
dent.
Warning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. The same applies if
battery is disconnected. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is in-
creased! Adjust your driving style according-
ly. For more information, see
“Electro-hydraulic brake system”
(page 92).

416 Practical hintsBatteries
Disconnecting the batteries
Apply the parking brake (
page 61).

Make sure the gear selector lever is set
to position P (
page 168).

Close the retractable hardtop
(page 199).

Turn off all electrical consumers.

Turn off the engine (
page 62).

Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*: Open
the driver’s door.

Open the trunk.

Read and observe safety instructions
and precautions (
page 281).

Open the luggage cover in the trunk
(page 206).

Remove the trunk floor.
The battery for electrical consumers is
located in the right hand area of the
trunk (
page 388).

Use the 10 mm open-end wrench from
the vehicle tool kit to disconnect the
negative lead from negative
terminal5 of the consumer battery
(page 414).
Warning!
G
With a disconnected battery

you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect


the gear selector lever will remain
locked in positionP
!
Always disconnect the batteries in the order
described below, even if you only want to charge
the starter battery, for example. Otherwise the
vehicle’s electronics can be damaged.

422 Practical hintsTowing the vehicleWarning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is
increased! Adapt your driving style
accordingly. For more information, see
“Electro-hydraulic brake system”
(page 92).
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.
!
When towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approx. 9 mph (15 km / h) or more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 119).
Towing of the vehicle should only be done using
the properly installed towing eye bolt. Never
attach tow cable, tow rope or tow rod to the
vehicle chassis, frame or suspension parts.
i
To signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position2 and activate the
combination switch for the left or right turn
signal in the usual manner – only the selected
turn signal will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
i
If the battery is disconnected or discharged


the SmartKey will not turn in the starter
switch


the gear selector lever will remain locked in
positionP.
For more information, see “Batteries”
(
page 414) and “Jump starting” (
page 419).