2007 MERCEDES-BENZ S550 DISP Button

94 Control systemsCOMAND FM/AM radioSwitching to radio mode 
Select “Audio”
“Audio”
“FM/AM
Radio”.
or

Press the M shortcut button once or
twice.
The radio display appears once you
have switched to radio mode. You will
hear the station/channel last tuned in
in the previously selected waveband,
provided that the station/channel can
be received.
Illustration: radio mode in FM waveband1Main area with frequency display
2Preset position of selected station
3Frequency of selected station
4Name of selected station
5Sound settings
6To switch to Weather Band
7To switch to AM waveband
8Selected waveband
9Preset options
aRadio options
Switching wavebands
You can switch between the FM, AM and
WB (Weather Band) wavebands.
Select “Audio”
“Audio”
“FM/AM
Radio”
“FM” or “AM” or “WB”.
You will hear the station last tuned in
on the selected waveband.
Selecting stations/channels
You have the following selection options:

The station list


The search function


The station presets


The manual frequency entry


The channel list
Selecting stations using the station list
i
The number of times you have to press the
M shortcut button depends on the operating
mode currently selected.
i
Station name display 4 is available for the
FM waveband and can only be seen when it is
switched on (
page 97) and if the station trans-
mits a name.
i
The station list is only available for the FM
waveband. It contains all the stations that can be
currently received and is sorted by station fre-
quencies.

99 Control systems
COMAND satellite radio* (USA only)
Switching to satellite radio
Select “Audio”
“Audio”
“Sat Ra-
dio”.
or

Press the M shortcut button once or
twice. The Satellite radio menu appears
if it was the last active radio mode.
The screen which then appears de-
pends on the activation status of the
satellite radio service.
The following options are possible:

Satellite radio service is not activat-
ed


Only the preview channel is activat-
ed


Satellite radio service is fully acti-
vatedSatellite radio service is not activated
The telephone number of the Sirius Service
Center and the twelve-digit electronic seri-
al number (SIRIUS-ID) of the particular re-
ceiver are displayed.
This information is required when calling
the Sirius Service Center for an activation
request.

Closing screen: Press n.Only the preview channel is activated
The satellite radio preview channel ap-
pears.
Satellite radio service is fully activated
The main satellite radio menu appears. You
will hear the channel last tuned in, provid-
ed that it can be received.
i
Credit card information is also required for
your application. The activation process takes
approximately 5 to 10 minutes after calling the
Sirius Service Center.
i
If only the preview channel is activated, you
cannot tune in another channel. If you try to do
this, you will see the screen described in the sec-
tion “Satellite radio service is not activated”
(
page 99).

111 Control systems
COMAND audio CD/audio DVD/MP3
Switching to audio CD, audio DVD or MP3 mode
Load CD / DVD (
page 107) or
PCMCIA card (
page 108).
or

Select “Audio”
“Audio”, then “CD” or
“DVD-Audio” or “MP3”.
or

Press the M shortcut button once or
twice.Example display in audio CD mode
1Current playback option
2Track number
3Disc number
4Disc name (only if saved on the disc)
5Track name (only if saved on the disc)
6Track time
7Graphic time and track display
8Sound settings
9Medium selection
aTo call up track listing
bDisc type
cPlayback optionsExample display in audio DVD mode
1Current playback option
2Track number
3Disc number
4Disc name (only if saved on the disc)
5Track name (only if saved on the disc)
6Track time
7Graphic time and track display
8Sound settings
9Medium selection
aTo call up track listing
bStop function
cPause (“Play” appears if paused)
dDisc type
ePlayback options
i
The M shortcut button takes you directly
to the previously set disc mode (audio CD,
audio DVD or MP3-CD/DVD). The number of
times you have to press the shortcut button de-
pends on the previously set mode.

125 Control systems
COMAND telephone*
If you have accepted the call using the
Bluetooth headset, the call will be conduct-
ed via the headset.
Further operating functions can be found
in the “Functions during a single-call con-
nection” section (
page 127).
You can also accept a call if the
COMAND display is showing a screen oth-
er than the telephone mode screen. After
accepting the call, you will see the caller’s
data in a window.

Closing window: Slide qmr oromp
or press n.
Making an outgoing callEntering the telephone number using
the COMAND controller

Switching screen to telephone
mode: Call up main telephone menu
(page 121).

Entering digits: Select desired digits
by rotating ymz or sliding omp and
press n.

Deleting individual digits: Select )
and briefly press n.

Deleting an entire telephone num-
ber: Select ) and press and hold n
until the telephone number is deleted.

Connecting a call: Select “S”.
Entering a telephone number using the
telephone keypad

Switching screen to telephone
mode: Call up main telephone menu
(page 121).

Use telephone keypad to enter digits.

Connecting a call: Press s.
Redial

Switching screen to telephone
mode: Call up main telephone menu
(page 121).

Use COMAND controller to select
“S”.
or

Press s on the telephone keypad
(page 82).
The list of dialed numbers appears. The
most recently dialed number is at the
top.

Select desired entry.

Connecting a call: Press n.
i
If you place an outgoing call and receive a
busy signal, the telephone automatically starts
to redial as long as the provider and the mobile
phone support this function (see mobile phone
operating instructions).
While the call is connecting, you can also send
character strings (
page 127).
i
A detailed description of how to enter digits
using the telephone keypad can be found on
(
page 82).
i
If the list of dialed calls contains no entries,
the “S” menu item cannot be selected and the
s button on the telephone keypad does not
function.

127 Control systems
COMAND telephone*

Deleting message: Press n.
Functions during a single-call connec-
tionIllustration: telephone mode during a call1Symbol for active telephone con-
nection (also visible in other operating
modes)
2Signal strength display
3To switch hands-free microphone on or
off
4Length of call display
5To send character strings
6To end a call
7Person you are callingSwitching the hands-free microphone
on or off

Switching screen to telephone
mode: Call up main telephone menu
(page 121).

Switching off microphone:
Select “Mic OFF” and press n.
or

Press F shortcut button.
If the microphone is switched off,
the> symbol appears in the main ar-
ea.

Switching on microphone:
Select “Mic ON”.
or

Press F shortcut button.
The> symbol disappears.
Sending a character string via DTMF
Answering machines or other devices can
be controlled by character strings (e.g. for
remote query functions).
Sending character strings via the DTMF
menu

During a call, select “DTMF”.
The DTMF dialing display appears.
i
The name of the person you are speaking
with can only be seen in display 7 if his or her
telephone number and name have been saved in
the COMAND address book or phone book on
the mobile phone. The telephone number must
also be saved in the same way in which the per-
son you are talking to transmits it.
i
This function is not possible with every mo-
bile phone. If the mobile phone supports the
function, you can use it during the call connec-
tion and also during a call.

128 Control systemsCOMAND telephone*1Back to the call display
2Character entry
3To call up the phone book
Sending individual characters:
Rotateymz or slide omp and select
desired character.
Each character you select can be seen
in the main area and is sent immediate-
ly.

Sending a phone book entry as a
character string: Select “Name”.

Select desired phone book entry.
The entry is immediately sent as a char-
acter string.

Switching back to the call display:
Select “Y”.
Sending character strings via the tele-
phone keypad

Press corresponding button on tele-
phone keypad.
Each character you select is immedi-
ately sent.
Ending an active call

Ending a call: Select “4END” in the
call display.
or

Press t on the telephone keypad or
on the multifunction steering wheel.
Transferring a call
From the hands-free system to the
Bluetooth headset
The call transfer is controlled by pressing
the PTT button on the Bluetooth headset
(see headset operating instructions). Nor-
mally, it is sufficient to press the PTT but-
ton once, but under certain circumstances
you may have to press it a second time.
Once the call has been transferred to the
Bluetooth headset, all the functions will be
available to you which are described in the
“Functions during a single-call connection”
section (
page 127).
Exception: “Switching the hands-free mi-
crophone on or off” function (
page 127).
i
Telephone numbers containing the + char-
acter may impair the function.
i
The + character may impair the function.
i
The use of a Bluetooth headset requires
Bluetooth to be activated and the Bluetooth
headset to be authorized (
page 217).

129 Control systems
COMAND telephone*
From the Bluetooth headset to the
hands-free system
On most Bluetooth headsets, you press the
PTT button on the headset twice quickly to
transfer the call (see headset operating in-
structions).
From the hands-free system to the mo-
bile phone
If the mobile phone has a folding up-
per section: flip upper section open.

Take mobile phone out of cradle.
The “No telephone inserted” message
appears on the COMAND display. Sub-
sequent operation is only possible us-
ing the mobile phone.From the mobile phone to the
hands-free system

Insert mobile phone into cradle.
Once the call has been transferred to
the hands-free feature, all the functions
will be available to you which are de-
scribed in the “Functions during a sin-
gle-call connection” section
(page 127).
COMAND phone book
The COMAND phone book contains both
the COMAND address book entries and
mobile phone entries that have at least
one telephone number.
The COMAND address book entries are
permanently available even when a mobile
phone is not inserted in the cradle.
When the mobile phone is inserted in the
cradle, COMAND will read the phone book
entries in the mobile phone and compares
them with the COMAND address book en-
tries. If any of the telephone numbers of a phone
book entry in the mobile phone are the
same as an address book entry, COMAND
will only display the address book entry.
If the entries are not the same, the CO-
MAND phone book will show the phone
book entry in the mobile phone.
Calling up the COMAND phone book

Select “Telephone”
“Telephone”

“Telephone”
“Name”.
The COMAND phone book appears.


131 Control systems
COMAND telephone*
Illustration: list of phone book entries with
name display and hidden smart speller1Back to smart speller
2To switch phone book display (“123” or
“ABC”)
3Symbol + for several telephone num-
bers (subentries) under the main entry,
subentry list is closed
4To call up options
5Symbol / for open subentry list
6List of phone book entries
7Subentry list with category symbols
and telephone numbers

Switching from the list to the smart
speller: Select “Back” from the list.
or

Press back button L in the center
console (
page 80).

Changing phone book display in the
list: Select “123” or “ABC”.
The screen changes to telephone num-
ber or name display.Closing the COMAND phone book

In the smart speller, select “Back”.
or

Press back button L in the center
console (
page 80).
Selecting an entry in the COMAND
phone book
Selecting entries using the smart speller

Switch from the list to the smart speller
if necessary.

Changing smart speller language:
Select !.

Select desired language.
i
The following options are available under
“Options” menu item 4:


Displaying details about an entry
(page 132)


Creating a new entry in the address book
(page 133)


Deleting an entry (
page 134)


Saving a phone book entry from mobile
phone in the address book (
page 134)


Adding a telephone number to an address
book entry (
page 136)