2007 MERCEDES-BENZ ML63AMG transmission

332 OperationDriving instructionsML 63 AMG
Your vehicle is factory equipped with
“Y”-rated tires, which have a speed rating
of 186 mph (300 km/h).
An electronic speed limiter prevents your
vehicle from exceeding a speed of
155 mph (250 km/h).
ML 63 AMG with increased top speed*
Your vehicle is factory equipped with
“Y”-rated tires, which have a speed rating
of 186 mph (300 km/h).
An electronic speed limiter prevents your
vehicle from exceeding a speed of
171 mph (275 km/h).
Winter driving instructions
The most important rule for slippery or icy
roads is to drive sensibly and to avoid
abrupt acceleration, braking and steering
maneuvers. Do not use the cruise control
system under such conditions.
When the vehicle is in danger of skidding,
shift the automatic transmission to
positionN. Try to keep the vehicle under
control by corrective steering action.Road salts and chemicals can adversely af-
fect braking efficiency. Increased pedal
force may become necessary to produce
the normal brake effect.
Depressing the brake pedal periodically
when traveling at length on salt-strewn
roads can bring road-salt-impaired braking
efficiency back to normal.
If the vehicle is parked after being driven
on salt-treated roads, the braking efficien-
cy should be tested as soon as possible af-
ter driving is resumed.
i
For information on speed ratings for winter
tires, see “Winter tires” (
page 399).
For additional general information on tire speed
markings on the tire sidewall, see “Tire speed
rating” (
page 397).
i
For information on driving with snow chains,
see “Snow chains” (
page 400).
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of control loss.
Warning!
G
Make sure not to endanger any other road
users when carrying out these braking
maneuvers.

333 Operation
Driving instructions
For more information, see “Winter driving”
(page 399).
Standing waterFor more information, see “Driving through
water” (
page 338).
Off-road driving
Warning!
G
If the vehicle becomes stuck in snow, make
sure that snow is kept clear of the exhaust
pipe and from around the vehicle with the
engine running. Otherwise, deadly carbon
monoxide (CO) gases may enter vehicle in-
terior resulting in unconsciousness and
death.
To assure sufficient fresh air ventilation,
open a window slightly on the side of the ve-
hicle not facing the wind.Warning!
G
The outside temperature indicator is not de-
signed to serve as an ice-warning device and
is therefore unsuitable for that purpose. In-
dicated temperatures just above the freez-
ing point do not guarantee that the road
surface is free of ice.
!
Do not drive through flooded areas or water
of unknown depth. Before driving through water,
determine its depth. Never accelerate before
driving into water. The bow wave could force wa-
ter into the engine and auxiliary equipment, thus
damaging them.
If you must drive through standing water, drive
slowly to prevent water from entering the pas-
senger compartment or the engine compart-
ment.
Water in these areas could cause


damage to electrical components


wiring of the engine or transmission
or could result


in water being ingested by the engine
through the air intake, causing severe inter-
nal engine damage.
Any such damage is not covered by the
Mercedes-Benz Limited Warranty.
i
Vehicles with air suspension package*:
Select the raised level (
page 270) before
driving through standing water.
Warning!
G
Do not load items on the basic carrier bars*.
It may cause instability during some maneu-
vers which could result in an accident.
Drive slowly in unknown terrain. This will
make it easier to recognize unexpected ob-
stacles and avoid damage to the vehicle.
To help avoid the vehicle rolling over, never
turn it around on steep inclines. If the vehi-
cle cannot complete the attempted climb,
back it down in reverse gear.
Do not drive along the side of a slope. The
vehicle might otherwise rollover. If in doing
so the vehicle begins to show a tendency to
roll, immediately steer into a line of gravity
(straight up or downhill).


335 Operation
Driving instructions
Off-road driving rules

Engage the off-road driving program
(page 268) before driving under
off-road conditions.


Vehicles with air suspension package*:
Make sure you select a vehicle level
(page 270) appropriate to the topo-
graphical conditions. Always make
sure the vehicle has enough ground
clearance.


Fasten items being carried as securely
as possible (
page 281).


Always navigate gradients with the en-
gine on and with the transmission en-
gaged in a gear. Switch on the DSR
(page 265) to help maintain a preset
speed.
!
Observe the following during off-road
driving:


Keep doors, tailgate, windows, and
tilt/sliding sunroof* closed whenever driving
off-road.


Adjust vehicle speed to condition of terrain.
The more uneven, rutty and steeper the ter-
rain, the lower the speed should be. Drive
through water slowly at an even speed,
avoiding a bow wave.


Be especially careful when driving in un-
known territory. It may be necessary to get
out of the vehicle and scout the path you in-
tend to take.


Watch out for obstacles, such as rocks,
holes, tree stumps and ruts.


Before driving through water, determine its
depth.


Do not stop vehicle while immersed in water,
and do not shut off the engine.


In sandy soil, drive at a steady speed as al-
lowed by conditions. This helps overcome
the vehicle rolling resistance and reduces
the likelihood of the vehicle sinking into the
ground.


Do not initiate jumps with the vehicle. It
interrupts the forward momentum of the
vehicle.


Always drive onto slopes with the engine
running and the vehicle in gear.


Do not shift automatic transmission to
positionN.Warning!
G
Do not reduce the tire inflation pressure
before driving through sand. However, if you
do so, remember to correct the tire inflation
pressure (
page 375) before continuing
your trip. Driving with reduced tire inflation
pressure increases the risk of losing control
of the vehicle and rolling over.

337 Operation
Driving instructions


Comply with the warnings
(page 333) and rules for off-road
driving (
page 335).


Driving on embankments, slopes and
other steep inclines should only be
done straight up or downhill, i.e. in the
line of gravity. Maximum vehicle climb-
ing ability is a 100% grade which is
equivalent to a slope angle of
45 degrees. Keep in mind that the
climbing ability of the vehicle depends
on terrain conditions.


Shift automatic transmission to
position1 (
page 193).


Drive slowly.


Avoid excessive engine speeds – drive
with moderate engine speeds
(max. 3 000 rpm).


Utilize the engine’s braking power
when descending a slope, observe the
engine speed (do not overrev the en-
gine). Apply the service brake as need-
ed.


Check the brakes after a lengthy down-
grade drive.Traction in steep terrain
The maximum vehicle climbing ability is a
100% grade which is equivalent to a slope
angle of 45 degrees. Keep in mind that the
climbing ability of the vehicle depends on
terrain conditions.
Be easy on the accelerator and watch for
continuous wheel traction when driving in
steep terrain.
Vehicles with air
suspension
package*
1
1
1
1Vehicles with AMG Sport-Package*
2
Raised level
34°
29°
31°
Highway
29°
22°
27°
ML 63 AMG
1
2
Raised level
28°
29°
Highway
23°
24°
i
For maximum engine speed, see “Instru-
ment cluster” (
page 26) and see “Engine”
(
page 534).Warning!
G
To help avoid the vehicle rolling over, never
turn it around on steep inclines. If the vehi-
cle cannot complete the attempted climb,
back it down in reverse gear.
i
The hill start assist system supports you
when driving uphill.
For more information, see “Hill start assist sys-
tem” (page 192).
i
The 4-ETS helps greatly when starting out on
a steep incline when the front wheels have then
the tendency to slip due to the weight shifting
towards the rear axle.
The 4-ETS recognizes the situation and limits the
torque for the front wheels by braking them.
Simultaneously the torque for the rear wheels is
increased.

338 OperationDriving instructionsDriving across a hilltop
Decelerate just ahead of a hilltop (do not
shift automatic transmission to
positionN), to prevent the vehicle from
speeding up too much after climbing a hill.
Use the momentum of the vehicle to drive
across the hilltop.
After climbing a hill, driving in this manner
prevents the vehicle from:

losing ground contact when cresting
hills


losing its forward momentum


speeding up too much after climbing
the hill
Driving downhill


Drive slowly.


Do not drive at an angle to the incline.
Steer into the line of gravity and drive
with the front wheels pointing straight
downhill. Otherwise, the vehicle may
slide sideways off the path and roll
over.


Shift automatic transmission to
position1 (
page 193).


On steep inclines, use the Downhill
Speed Regulation (
page 264).


Utilize the engine’s braking power to
reduce vehicle speed.
If this is insufficient, apply the brakes
gently. Make sure the vehicle is moving
in the line of gravity.


Check the brakes after a lengthy down-
grade drive.Driving through water
1Fording depth
i
The special Off-road – ABS (
page 97) set-
ting allows for precise and brief (cyclical) block-
ing of the front wheels, permitting them to dig
into loose ground.
Remember that, when stopped, the front wheels
slide across a surface and thus lose their ability
to steer the vehicle.
Vehicles with steel
suspension
120.00 in (50 cm)
Vehicles with air
suspension
package* or
ML 63 AMG
1
Raised level
20.00 in (50 cm)

339 Operation
Driving instructions


Before driving through water, deter-
mine its depth.


Vehicles with air suspension package*:
Select the highest vehicle level
possible (
page 270).


Switch to off-road driving program
(page 268) before driving through
water.


Shift automatic transmission to
position1 or2 (
page 193).


Avoid high engine speeds.


Enter and leave the water only at a
shallow spot, driving at walking speed.


Drive through the water slowly and at a
constant speed.


Do not stop vehicle while immersed in
water, and do not shut off the engine.


There is a very high level of driving re-
sistance in water. The surface is slip-
pery and may not be firm, making
pulling away in water difficult and dan-
gerous.


Make sure that only small bow waves
are formed when driving the vehicle
through water.


Clean mud off the tire tread after driv-
ing through water.


To dry the brakes, apply pressure to the
brake pedal several times while driving
after leaving the water.Crossing obstacles
!
The water depth must not exceed the
respective value listed in the table. The ground
under the water might not be firm which could
result the water being deeper than expected
when driving the vehicle through it. Please note
that the water level is correspondingly lower for
flowing water.
!
Never accelerate before driving into the
water. The bow wave could force water into the
engine and auxiliary equipment, thus damaging
them.
!
Do not open any of the vehicle’s doors while
driving through water. Water could otherwise en-
ter the vehicle interior and damage the vehicle’s
electronics, as well as the interior equipment.
!
Obstacles can damage the vehicle
underbody or suspension components. If possi-
ble use the assistance of a second person out-
side the vehicle to scout the path you intend to
take and check for adequate ground clearance
when you cross obstacles with your vehicle. The
person assisting you outside the vehicle should
always be a safe distance away from the vehicle
and positioned so that he or she cannot get hurt
in case of any unexpected vehicle movement.
After off-road driving or crossing obstacles, in-
spect vehicle for any damage, especially vehicle
underbody and suspension components. Failure
to do so can adversely affect the vehicle’s future
performance, including increased chance of an
accident.

340 OperationDriving instructionsWhen driving over tree stumps, big rocks
and other obstacles, observe the following
rules:

Make sure the off-road driving program
(page 268) is switched on.


Avoid high engine speeds.


Shift automatic transmission to
position1 (
page 193).


Check the vehicle clearance before
crossing obstacles.


Cross obstacles (e.g. tree stumps or
big rocks) very slowly by aiming one of
the front wheels at the center of the ob-
stacle, and repeat same with the rear
wheel.Driving on sand
When driving on sand, observe the follow-
ing rules:


Vehicles with air suspension package*:
Set the raised level (
page 270).


Avoid high engine speeds.


Shift automatic transmission into a
gear range that is appropriate for the
terrain.


In sandy soil, drive at a steady speed as
allowed by conditions. This helps over-
come the vehicle rolling resistance and
reduce the likelihood of the vehicle
sinking into the ground.


Drive in tracks of other vehicles if they
are not too deep and if you have suffi-
cient clearance.
Ruts
A number of off-road tracks or other by-
ways have deep ruts which can cause the
underbody to come in contact with the
ground.


Make sure the off-road driving program
(page 268) is switched on.


Vehicles with air suspension package*:
Set the raised level (
page 270).
!
Special attention is needed when you cross
obstacles on a steep incline.
The vehicle could slide sideways as a result of its
possible slanted position which in turn may
result in the vehicle tipping or rolling over.
Warning!
G
Do not reduce the tire inflation pressure
before driving through sand. However, if you
do so, remember to correct the tire inflation
pressure (
page 375) before continuing
your trip. Driving with reduced tire inflation
pressure increases the risk of losing control
of the vehicle and rolling over.

341 Operation
Driving instructions


Avoid high engine speeds.


Shift automatic transmission to
position1 (
page 193).


Drive next to the ruts rather than
through them if at all possible.


If the ruts are too deep to drive in, drive
with one side of the vehicle on the
grassy center strip if the route permits.Returning from off-road drivingOff-road driving increases strain on the
vehicle.
We recommend that you inspect the vehi-
cle for possible damage after each off-road
trip. Recognizing any damage and a subse-
quent timely repair reduces the chance of
a possible breakdown or accident later on.
Proceed as follows:


Switch off the off-road driving program
(page 268).


Switch off the DSR (
page 265).


Vehicles with air suspension package*:
Lower the vehicle back to a level
suitable for road conditions, e.g. High-
way/High-speed level (
page 270).


Clean all exterior lamps and check for
possible damage.


Clean the front and rear license plate.
!
Check that the ruts are not too deep and
your vehicle’s clearance is sufficient. Otherwise:


your vehicle may be damaged


the underbody of the vehicle may come in
contact with the ground and you may get
stuck
Warning!
G
If you feel a sudden significant vibration or
ride disturbance, or you suspect that possi-
ble damage to your vehicle has occurred,
you should turn on the hazard warning flash-
ers, carefully slow down, and drive with cau-
tion to an area which is a safe distance from
the roadway.
Inspect the tires and under the vehicle for
possible damage. If the vehicle or tires ap-
pear unsafe, have it towed to the nearest
Mercedes-Benz Light Truck Center or tire
dealer for repairs.
Damage to the vehicle may influence driving
comfort and pose the risk of accident to you
and other drivers.