2007 MERCEDES-BENZ ML500 open hood

492 Practical hintsReplacing bulbsLicense plate lamp
1License plate lamp cover
2Screws
Loosen screws2.

Remove license plate lamp cover1.

Replace the tubular bulb.

Reinstall license plate lamp cover1.

Retighten screws2.
Adjusting headlamp aim
VVertical centerline
HHeadlamp mounting high, measured
from the centerCorrect headlamp adjustment is extremely
important. To check and readjust a head-
lamp, follow the steps described:

Park the vehicle on a level surface
25 feet (7.6 m) from a vertical test
screen or wall.

Switch the headlamps on
(page 136).
If the beam does not show a beam pattern
as indicated in the figure left, then follow
the steps below:

Open hood (
page 356).
i
High beam adjustments simultaneously aim
the low beam.
Vehicle should have a normal tailgate load.

494 Practical hintsReplacing wiper bladesFront wiper blades
Removing

Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*:
Make sure the vehicle’s on-board
electronics have status0
(page 42).

Fold the wiper arms forward until they
engage.
1Wiper blade
2Cover
3Attachment
4Tab
5Removing

Press tabs4 together and tilt wiper
blade1 to detach tabs4 on both
recesses of attachment3.
Wiper blade1 is released on one end.

Maintaining its tilted position, slide
wiper blade1 out of attachment3 in
direction of arrow5.
Warning!
G
For safety reasons, switch off wipers and
remove SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the
vehicle’s on-board electronics have
status
0) before replacing a wiper blade.
Otherwise the motor could suddenly turn on
and cause injury.
Warning!
G
Wiper blades are components that are sub-
ject to wear and tear. Change the wiper
blades twice a year, preferably in the spring
and fall. Otherwise the windows will not be
properly wiped. As a result, you may not be
able to observe surrounding traffic condi-
tions and could cause an accident.
!
Never open the hood when the wiper arms
are folded forward.
Hold on to the wiper when folding the wiper arm
back. If released, the force of the impact from
the tensioning spring could crack the windshield.
Do not allow the wiper arms to contact the wind-
shield glass without a wiper blade inserted.
Make sure the wiper blades are properly
installed. Improperly installed wiper blades may
cause windshield damage.
For your convenience, we recommend that you
have this work carried out by an authorized
Mercedes-Benz Light Truck Center.
!
Do not pull on the wiper blade inserts. They
could tear.

516 Practical hintsJump startingThe jump-start contacts are located in the
engine compartment.1Negative (-) terminal
2Positive (+) terminal

Make sure the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Set automatic transmission to
positionP.

Open the hood (
page 356).

Open cover of positive terminal2.1Positive terminal of charged battery
2Positive terminal of discharged battery
3Negative terminal of charged battery
4Negative terminal of discharged
battery
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 507).

523 Practical hintsFuses
Fuse box in engine compartment
The fuse box is located on the passenger
side of the engine compartment.
Open the hood (
page 356).
Example fuse box ML 350 (ML 320 CDI,
ML 63 AMG similar)1Clamp
2Fuse box cover
Fuse box ML 5001Clamp
2Fuse box cover
Pull clamp1 in direction of arrow.

Lift fuse box cover2 up.

Install fuse box cover in reverse order.

Close the hood after checking or
replacing fuses (
page 358).
Fuse box in cargo compartment
The fuse box is located in the cargo com-
partment behind the passenger side trim
panel.
1Lock
2Cover
!
The fuse box cover must be installed
properly to prevent moisture and/or dirt from
entering the fuse box and possibly impairing fuse
operation.

562 IndexHeadlamps
Automatic headlamp mode 137
Bi-Xenon* 458, 486
Cleaning lenses 408
Cleaning system* 200, 363
Halogen 485
High beam see High beam flasher
High beam see High beam headlamps
Light sensor, Messages in the
multifunction display 460
Low beam see Low beam headlamps
Manual headlamp mode 137
Messages in the
multifunction display 458, 459,
460, 461, 462, 463
Replacing bulbs 482, 483
Switch 59, 136
Heated seats see Seat heating*
Heated steering wheel* 304
Height adjustment
Vehicle level control (Vehicles with
Air suspension package*) 271High beam flasher 59, 140
High beam headlamps
Indicator lamp 29
Messages in the
multifunction display 459
Replacing bulbs 483, 485, 486
Switching on 59, 140
High mounted brake lamp 483
Hood 356
Messages in the
multifunction display 455
Opening 356
Hooks
Loading 284
Horn 25
HVAC see Climate control or
automatic climate control (3-zone)*
Hydroplaning 330I
Identification labels see Labels
Ignition 40, 42, 55
Immobilizer 103
Indicator lamps see Lamps, Indicator and
warning
Infant and child restraint systems see
Children in the vehicle
Inflation pressure see Tires,
Inflation pressures
Information button see Tele Aid*
Infrared reflecting windshield* 322
Inside door handle 118
Instrument cluster 26, 28, 145
Illumination brightness 145
Lamps 414
Messages in display see
Multifunction display messages
Multifunction display 147
Outside temperature indicator 146
Selecting language 167
Instrument lighting see Instrument cluster,
Illumination brightness 145
Instrument panel see Instrument cluster
Instruments and controls see Cockpit