2007 MERCEDES-BENZ ML320CDI engine

157 Controls in detail
Control system
RACETIMER
The RACETIMER allows you to time and
save driving stretches in hours, minutes
and seconds.
Press buttonè orÿ repeatedly
until you see the AMG menu.

Press buttonj repeatedly until you
see the RACETIMER.
1Gear indicator
2RACETIMER
3LapStarting the RACETIMER

Press buttonæ.
The timer starts.
Displaying intermediate time

Press buttonç while the timer is
running.
The intermediate time is shown for five
seconds.
Stopping the RACETIMER

Press buttonæ.
The timer stops.
Warning!
G
The RACETIMER feature is only for use on
roads and in conditions where high speed
driving is permitted. Racing on public roads
is prohibited under any circumstances and
the driver is and must always remain re-
sponsible for following posted speed limits.
i
You can start the RACETIMER when the
engine is running or the starter switch is in
position2 (
page 40).
i
While the RACETIMER is being displayed,
you cannot adjust the volume using
buttonsæ orç.
i
When you stop the vehicle and turn the
SmartKey to position 1 (
page 40) or, in vehi-
cles with KEYLESS-GO*, turn off the engine and
do not open the driver’s door, the RACETIMER
stops timing. Timing is resumed when you switch
the ignition back on (
page 40) or restart the
engine (
page 54) and then press the
æbutton.

158 Controls in detailControl systemSaving lap time and starting a new lap
Press buttonç while the timer is
running.
The intermediate time will be shown for
five seconds.

Press buttonç within 5 seconds.
The intermediate time shown will be
saved as a lap time.
The RACETIMER begins timing the new
lap. The new lap begins to be timed as
soon as the intermediate time is called
up.
1Gear indicator
2RACETIMER
3Best lap time
4Lap numberResetting current lap

Press buttonæ while the timer is
running.
The timer stops.

Press buttonç.
The lap time is reset to “0”.
Deleting all laps

Press buttonæ while the timer is
running.
The timer stops.

Press the reset button twice
(page 26).

Press buttonæ.
The timer starts. The saved laps are
deleted.Overall analysis

Press buttonè orÿ repeatedly
until you see the AMG menu.

Press buttonj repeatedly until you
see the overall analysis.
1Overall analysis of RACETIMER
2Overall driving time
3Maximum speed
4Overall distance driven
5Average speed
i
You can save up to nine laps.
i
It is not possible to delete a single saved lap.
i
When you switch off the engine, the
RACETIMER will be reset to“0” after 30 seconds.
All laps are deleted.
i
These functions are only available if you
have saved at least one lap and have stopped the
RACETIMER.

159 Controls in detail
Control system
Lap analysis
Press buttonè orÿ repeatedly
until you see the AMG menu.

Press buttonj repeatedly until you
see the lap analysis.
1Lap number
2Lap time
3Maximum speed
4Lap length
5Average speed during lap

Press buttonj ork to see
other lap analyses.
Off-road mode menu
Use this function to switch the off-road
driving program (
page 268)
On or
Off
.

Press buttonè orÿ repeatedly
until you see the Off-road mode menu.
Off-road mode
Press buttonæ orç to switch
the off-road driving program
On or
Off
.The symboly appears in the lower
multifunction display.
Audio menu
The functions in the
Audio
menu operate
the audio equipment which you currently
have turned on.
If no audio equipment is currently turned
on, the message
Audio off
appears in the
multifunction display.
i
These functions are only available if you
have saved at least two laps and have stopped
the RACETIMER.
i
Each lap is shown in its own submenu. The
fastest lap is indicated by flashing symbol1.
i
This function is only available in AMG
vehicles.
i
The setting is stored when you turn off the
engine.

164 Controls in detailControl systemShould the vehicle’s system record any
conditions while driving, the number of
messages will reappear in the multifunc-
tion display

when the SmartKey in the starter
switch is turned to position0 or
removed from the starter switch.
or


when you turn off the engine by
pressing the KEYLESS-GO* start/stop
button (
page 67) in the starter
switch once and open the driver’s door
(this puts the starter switch in
position0, same as with the SmartKey
removed from the starter switch)
Settings menu
In the
Settings
menu there are two
functions:


The function
Reset to factory
settings?
, with which you can reset all
the settings to the original factory
settings.


A collection of submenus with which
you can make individual settings for
your vehicle.

Press buttonè orÿ repeatedly
until the
Settings
menu appears in the
multifunction display.The following settings and submenus are
available in the
Settings
menu:
i
The vehicle status message memory will be
cleared when you turn the SmartKey in the start-
er switch to position1 or2, or when you press
the KEYLESS-GO* start/stop button once or
twice without depressing the brake pedal. You
will then only see high priority messages in the
multifunction display (
page 428).
Function
Page
Resetting all settings
165
Submenus in the settings menu
165
Instrument cluster submenu
167
Time/date submenu
169
Lighting submenu
171
Vehicle submenu
174
Comfort submenu*
177

171 Controls in detail
Control system
Lighting submenu
Access the
Lighting
submenu via the
Settings
menu. Use the
Lighting

submenu to change the lamp and lighting
settings on your vehicle.
The following functions are available:
Setting daytime running lamp mode
(USA only)

Move the selection marker with
buttonæ orç to the
Lighting

submenu.

Press buttonj ork repeatedly
until the message
Lamp circuit
headlamp
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to select
manual operation (
Manual
) or daytime
running lamp mode (
Constant
).
With daytime running lamp mode activated
and the exterior lamp switch at
positionMorU, the low beam
headlamps are switched on when the
engine is running.In low ambient light conditions the
following lamps will switch on additionally:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps
For more information on the daytime
running lamp mode, see “Lighting”
(
page 136).
Function
Page
Setting daytime running lamp
mode (USA only)
171
Setting locator lighting
172
Setting night security illumination
172
Setting interior lighting delayed
shut-off
173
i
This function is not available in countries
where the daytime running lamp mode is
mandatory and therefore in a constant mode.
i
For safety reasons, changing the setting for
the daytime running lamp mode is not possible
while the vehicle is in motion. The following
message appears in the multifunction display:
Settings
only possible
at standstillFor safety reasons, resetting to factory settings
(page 165) while driving will not deactivate the
daytime running lamp mode.

172 Controls in detailControl systemSetting locator lighting
With the locator lighting feature activated,
the exterior lamp switch in positionU
(page 136) and the interior lighting in
automatic mode (
page 143), the follow-
ing lamps will switch on during darkness
when the vehicle is unlocked using
buttonΠon the SmartKey or SmartKey
with KEYLESS-GO:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps


Front fog lamps*
The locator lighting switches off when the
driver’s door is opened.
If you do not open a door after unlocking
the vehicle with the SmartKey, the lamps
will switch off automatically after
approximately 40 seconds.

Move the selection marker with
buttonæ orç to the
Lighting

submenu.

Press buttonj ork repeatedly
until the message
Function Surround
lighting
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to switch
the locator lighting function
On or
Off
.

Turn the exterior lamp switch to
positionU when exiting the vehicle.
The locator lighting feature is
activated.Setting night security illumination
(Headlamps delayed shut-off)
Use this function to set whether you would
like the exterior lamps to remain on for
15 seconds during darkness after exiting
the vehicle and closing all doors.
With the headlamps delayed shut-off
feature activated and the exterior lamp
switch in positionU before the engine
is turned off, the following lamps will
switch on when the engine is turned off:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps


Front fog lamps*
If after turning off the engine you do not
open a door or do not close an opened
door, the lamps will automatically switch
off after 60 seconds.

173 Controls in detail
Control system

Move the selection marker with
buttonæ orç to the
Lighting

submenu.

Press buttonj ork repeatedly
until the message
Headlamp delayed
shut-off
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to switch
the headlamps delayed shut-off feature On or
Off
.

Turn the exterior lamp switch to
positionU before turning off the
engine.
The headlamps delayed shut-off
feature is activated.
You can temporarily deactivate the
headlamps delayed shut-off feature:

Before exiting the vehicle, turn the
SmartKey in the starter switch to
position0.

Then turn it to position2 and back
to0.
The headlamps delayed shut-off
feature is deactivated. It will reactivate
as soon as you reinsert the SmartKey in
the starter switch.
Vehicles with KEYLESS-GO*:

Press KEYLESS-GO start/stop button
in the starter switch (
page 41).Setting interior lighting delayed shut-off
Use this function to set whether you would
like the interior lighting to remain on for
10 seconds during darkness after you have
removed the SmartKey from the starter
switch.

Move the selection marker with
buttonæ orç to the
Lighting

submenu.

Press buttonj ork repeatedly
until the message
Int. light.
delayed shut-off appears in the
multifunction display.
The selection marker is on the current
setting.

Press buttonæ orç to switch
the interior lighting delayed shut-off
feature
On or
Off
.

175 Controls in detail
Control system

Press buttonj ork repeatedly
until the message
Compass setting
Zone
appears in the multifunction
display.
The selection marker is on the current
setting.

Press buttonæ orç to set the
respective compass zone.
For information on how to call up the
compass, see “Compass” (
page 321).Compass calibration
This function is not available if your vehicle
is equipped with the COMAND system and
navigation module*.
In order to calibrate the compass properly,
mind the following:


Calibrate the compass in open terrain.
Nearby buildings, bridges, power lines
and large antenna masts, for example,
could impair compass calibration.


Switch off electrical consumers (e.g.
climate control, windshield wipers, or
rear window defroster).


Close all doors and the tailgate.

Start the engine (
page 54).

Press buttonæ orç to move
the selection marker to the
Vehicle
submenu.

Press buttonj ork repeatedly
until the message Compass Calibration
appears in the
multifunction display.
The selection marker is on setting
switched off
.

Press buttonæ to set the selection
marker to
Start
.
The following message appears in the
multifunction display:
Compass Calibration active
Please drive in a full circle
i
Make sure you are in area where you can
drive a full circle with your vehicle without dis-
turbing traffic in order to calibrate the compass.