2007 MERCEDES-BENZ G55AMG mirror controls

179 Controls in detail
Good visibility
Sun visors
The sun visors protect you from sun glare
while driving.
1Sun visor
2Mounting3Vanity mirror cover
4Vanity mirror lamps
Glare through the windshield
Swing sun visor1 down.
When you do not experience glare
anymore, swing sun visor1 up.Vanity mirror
Swing sun visor1 down.
Flip up vanity mirror cover3 to access
vanity mirror.
Vanity mirror lamps4 come on.
After using vanity mirror, flip down
vanity mirror cover3.
Swing sun visor1 up.
Warning!G
Do not use the vanity mirror while driving.
Keep the mirrors in the sun visors closed
while vehicle is in motion. Reflected glare
can endanger you and others.
iMake sure the ignition is switched on
(
page 39) and sun visor1 is properly
engaged in mounting2.

180 Controls in detail
Good visibility
Glare to a side window
Swing sun visor1 down.
Disengage sun visor1 from
mounting2.
Pivot sun visor1 to the side.
When you do not experience glare
anymore, pivot sun visor1 to the
windshield.
Engage sun visor1 into mounting2.
Swing sun visor1 up.
Windshield defroster
The windshield defroster uses a large
amount of power. To keep battery drain to
a minimum, switch off the windshield
defroster as soon as the windshield is
clear.
The windshield defroster switches off
automatically after 10 minutes.
If you switch on the windshield defroster
for the fourth time in succession, it will
switch off automatically after 5 minutes.
You cannot switch on the windshield
defroster if the outside temperature is
above 10°C (50°F).The windshield defroster switch is located
on the upper part of the center console.
1Windshield defroster switch
2Indicator lamp
Switch on the ignition (
page 39).
!To avoid damage to vanity mirror cover3,
make sure it is closed before pivoting sun
visor1 to the side.
Warning!G
Any accumulation of snow and ice should be
removed from the windshield before driving.
Visibility could otherwise be impaired,
endangering you and others.

205 Controls in detail
Driving systems
Move the gear selector lever to reverse
gearR (
page 162).
The area behind the vehicle appears in
the COMAND system display.
Switching the rear view camera off
Move the gear selector lever to
positionP,N orD.
or
Select another function on the
COMAND system.
iThe area behind the vehicle is shown in the
COMAND system display as a mirror image, like
in the rear view mirror.
iThe image from the rear view camera will
no longer be displayed if you select another
function on the COMAND system while reverse
gearR is engaged. To display the image again,
disengage and reengage reverse gearR.

230 Controls in detail
Useful features
System self-check
Initially, after switching on the ignition,
malfunctions are detected and indicated
(the indicator lamps in the SOS button, the
Roadside Assistance button• and the
Information button¡ stay on longer
than 10 seconds or do not come on). The
message
Tele Aid inoperative appears
in the multifunction display.Emergency calls
An emergency call is initiated auto-
matically following an accident in which
the emergency tensioning devices (ETDs)
or air bags deploy.
An emergency call can also be initiated
manually by opening the cover next to the
interior rear view mirror labeled SOS, then
briefly pressing the button located under
the cover. See (
page 231) for
instructions on initiating an emergency call
manually.
Once the emergency call is in progress, the
indicator lamp on the SOS button will
begin to flash. The message
Connecting
call
appears in the multifunction display.
When the connection is established, the
message
Call connected appears in the
multifunction display. All information
relevant to the emergency, such as the
location of the vehicle (determined by the
GPS satellite location system), vehicle
model, identification number and color are
generated.
iWhen a Tele Aid call has been initiated,
the COMAND system audio is muted and the
selected mode (radio, CD etc.) pauses.
The optional cellular phone (if installed) inserted
in cradle switches off. If you must use this
phone, we recommend that you use it only with
the vehicle at a standstill in a safe location.
Remove the phone from the cradle and place the
call. The navigation system (if engaged) will con-
tinue to run. The display in the instrument cluster
is available for use, and spoken commands are
only available by pressing the RPT button on the
COMAND system. A pop-up window will appear
in the COMAND system display to indicate that a
Tele Aid call is in progress. After the Tele Aid call
has ended, the optional cellular phone inserted
in the cradle switches on again. A PIN entry
might be necessary.
Warning!G
If the indicator lamps on the SOS button, on
the Roadside Assistance button, and/or on
the Information button remain illuminated
continuously in red and/or the message
Tele Aid inoperative is displayed in the
multifunction display after the system
self-check, a malfunction in the system has
been detected.
If a malfunction is indicated as outlined
above, the system may not operate as
expected. Have the system checked at the
nearest Mercedes-Benz Light Truck Center
as soon as possible.

237 Controls in detail
Useful features
Interior rear view mirror with integrated
remote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of
vehicle equipment):
5Hand-held remote control of
garage door opener, gate
operator or other device
6Hand-held remote control
buttonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 39).
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent
potential harm or damage. When program-
ming a garage door opener, the door moves
up or down. When programming a gate oper-
ator, the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
- signaling the door to stop and reverse -
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park the vehicle outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health.
All exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.


440 Index
Immobilizer 96
Activating 96
Deactivating 96
Infant and child restraint systems 79
Installing 84
LATCH child seat anchors 83
Information button see Tele Aid
Inside rear view mirror
Auto-dimming 177
Installing
Cargo compartment cover blind 214
Infant and child restraint systems 84
Wiper blades 389
Instructions
Loading 208
Instrument cluster 26, 130
Coolant temperature gauge 131
Digital speedometer 140
Illumination 130
Lamps in 324–334
Multifunction display 133
Outside temperature 140
Outside temperature indicator 132
Selecting language 149
Instrument lighting 130
Instruments and controls see CockpitInterior lighting
Automatic operation 125
Delayed shut-off 154
Manual operation 126
Interior lighting, front 125
Interior lighting, rear 126
Interior rear view mirror
Adjusting 46
Intermittent wipe 60
Activating 60
Deactivating 60
Intermittent wiping 59
J
Jack 367
Jump starting 399K
Key
Messages in display 353
Key, mechanical 370
Key, SmartKey
Battery check lamp 102
Checking the batteries 103
Factory setting 102
Global locking 102
Global unlocking 102
Loss of 103
Positions in starter switch 39
Remote control 100
Restoring to factory setting 103
Selective setting 102
Starting the engine 54
Unlocking with 38
Keys 100
Kickdown (Automatic transmission) 166
Kilometers/miles in speedometer 149
Kilopascal 305
Km/h or mph in speedometer 149
L
Labels, identification 412
Lamp bulbs, exterior 377
Lamp in center console 337