Page 345 of 457
344 Practical hints
What to do if …
Symbol messages
Display symbolDisplay messagePossible cause/consequencePossible solution
#The battery is no longer charging.
Possible causes:
alternator malfunctioning
broken poly-V-belt
Stop the vehicle in a safe location or as soon
as it is safe to do so.
Apply the parking brake (page 62).
Turn off the engine.
Check the poly-V-belt.
If it is broken:
Do not continue to drive.
Otherwise, the engine will overheat due to an
inoperative water pump which may result in
damage to the engine.
Contact an authorized Mercedes-Benz Light
Truck Center.
If it is in order:
Contact an authorized Mercedes-Benz Light
Truck Center immediately.
Page 347 of 457
346 Practical hints
What to do if …
Display symbolDisplay messagePossible cause/consequencePossible solution
3Check brake
fluid levelThere is insufficient brake fluid in the
reservoir.Risk of accident!
Carefully stop the vehicle in a safe location or
as soon as it is safe to do so.
Apply the parking brake (page 62).
Do not drive any further.
Contact an authorized Mercedes-Benz Light
Truck Center.
Do not add brake fluid! This will not solve the
problem.
Warning!G
Driving with the message Check brake
fluid level
displayed can result in an
accident. Have your brake system checked
immediately.
Do not add brake fluid before checking the
brake system. Overfilling the brake fluid res-
ervoir can result in spilling brake fluid on hot
engine parts and the brake fluid catching
fire. You can be seriously burned.
!If you find that the brake fluid in the brake
fluid reservoir has fallen to the minimum mark or
below, have the brake system checked for brake
pad thickness and leaks.
Page 348 of 457

347 Practical hints
What to do if …
Display symbolDisplay messagePossible cause/consequencePossible solution
;(USA only)
! (Canada only)
Release
parking
brakeYou are driving with the parking brake
set.Release the parking brake
(
page 55).
2Brake
wearThe brake pads have reached their wear
limit.Have the brake pads replaced as
soon as possible.
BTop up
coolant
See
Operator’s
ManualThe coolant level is too low.Add coolant (page 274).
If you have to add coolant frequently,
have the cooling system checked at
an authorized Mercedes-Benz Light
Truck Center.
!Brake pad thickness must be visually
checked by a qualified technician at the intervals
specified in the Maintenance Booklet.
Warning!G
Do not spill antifreeze on hot engine parts.
Antifreeze contains ethylene glycol which
may burn if it comes into contact with hot
engine parts. You could be seriously burned.
!Do not ignore the low engine coolant level
warning. Extended driving with this message and
symbol displayed may cause serious engine
damage not covered by the Mercedes-Benz
Limited Warranty.
Do not drive without sufficient amount of coolant
in the cooling system. The engine will overheat,
causing major engine damage.
Page 349 of 457
348 Practical hints
What to do if …
Display symbolDisplay messagePossible cause/consequencePossible solution
•Coolant
Stop, turn
engine offThe coolant is too hot.
Among other possible causes, the
poly-V-belt could be broken.Stop the vehicle in a safe location or as soon
as it is safe to do so.
Apply the parking brake (page 62).
Turn off the engine.
Check the poly-V-belt.
If it is broken:
Do not continue to drive.
Otherwise, the engine will overheat due to an
inoperative water pump which may result in
damage to the engine.
Contact an authorized Mercedes-Benz Light
Truck Center.
If it is in order:
Wait for the message to disappear before
restarting the engine.
Doing otherwise could result in serious engine
damage that is not covered by the
Mercedes-Benz Limited Warranty.
(Continued on next page)
Page 364 of 457
363 Practical hints
What to do if …
Display symbolDisplay messagePossible cause/consequencePossible solution
§Transfer
case
Visit
workshopThe transfer case is malfunctioning.Do not switch the transfer case on.
Contact an authorized Mercedes-Benz
Light Truck Center as soon as
possible.
TC
shift
procedure
canceledThe shift process in the transfer case was
canceled because of a malfunction.Repeat the shift process (page 170).
TC
shift
conditions
not fulfilledYou have not met the shift conditions for
a selection process in the transfer case.Repeat the shift process (page 170).
TC
in neutralNo gear has been selected in the transfer
case, it is in NEUTRAL.Engage transfer case to gear position
HIGH or LOW (
page 170).
Warning!G
If the transfer case is in NEUTRAL,
thePposition of the transmission will not
hold the vehicle. The parking brake must be
applied to hold vehicle in place.
Page 368 of 457

367 Practical hints
Where will I find...?
Vehicle jack
The vehicle jack is stored in a storage com-
partment under the rear bench seat on the
passenger side.
1Cover
2Tab
3Vehicle jack
Fold the rear bench seat forward
(
page 207).
Open cover1.
Open tab2 and remove vehicle
jack3 from the compartment.Observe the safety guidelines in the “Flat
tire” section (
page 390) when using the
vehicle jack.
Warning!G
The jack is designed exclusively for jacking
up the vehicle under the axle housing. To
help avoid personal injury, use the jack only
to lift the vehicle during a wheel change.
Never get beneath the vehicle while it is
supported by the jack. Keep hands and feet
away from the area under the lifted vehicle.
Always firmly set parking brake and block
wheels before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface.
Make sure the jack is positioned correctly
under the axle housing. Always lower the
vehicle onto sufficient capacity jackstands
before working under the vehicle.
If the vehicle is not raised as described, it
could slip off the jack as a result of vibra-
tions (e.g. opening or closing a door or the
tailgate).
Page 379 of 457
378 Practical hints
Replacing bulbs
Front lamps Rear lamps
LampType
1Additional turn signal
lampLED
2Locator lighting lampW6W
3Turn signal lamp1156 NA
4Side marker lampT4W
5Bi-Xenon headlamp:
Low and high beam1
1Bi-Xenon headlamp: Low beam and high beam use
the same D1S-35 W lamp. Do not replace the
Bi-Xenon bulbs yourself. Contact an authorized
Mercedes-Benz Light Truck Center.
D1S-35 W
Parking and standing
lampW5W
Blue vision
6Front fog lampH11 (55 W)
LampType
7High mounted brake
lampLED
8Turn signal lampPY 21 W
Brake and tail lampP21/5W
Tail, parking and
standing lampW5W
9Backup lampP21W
aLicense plate lampsC5W
bRear fog lampP21W
cSide marker lampT4W
Page 387 of 457

386 Practical hints
Replacing bulbs
Left tail lamp unit shown, right tail lamp
unit laterally reversed
3Turn signal lamp bulb
4Brake, tail, parking and standing lamp
bulb
5Tail, parking and standing lamp bulb
Press gently onto respective
bulb3,4, or5 and turn counter-
clockwise out of its bulb socket.
Press the new bulb gently into the bulb
socket and turn clockwise until it
engages.
Reinstall tail lamp lens2.
Install and tighten securing screws1.Rear fog lamp bulb/Backup lamp bulb
The following description applies to both,
the rear fog lamp and the backup lamp.
Rear fog lamp shown
1Securing screw
2Lamp lens
Loosen and remove securing
screws1.
Remove lamp lens2.3Bulb
Press gently onto bulb3 and turn
counterclockwise out of its bulb
socket.
Press the new bulb gently into the bulb
socket and turn clockwise until it
engages.
Reinstall lamp lens2.
Install and tighten securing screws1.
iDo not overtighten securing screws1.
Otherwise tail lamp lens2 could be damaged.
iDo not overtighten securing screws1.
Otherwise lamp lens2 could be damaged.