2007 MERCEDES-BENZ E-Class display

28 At a glance
Menu system
Right side:
General status information is displayed, re-
gardless of the selected operating mode.
In this example:
ROAMING = telephone* is logged into a
mobile communications network out-
side your home network.
 = telephone* signal strength
Menu functions and submenus
Using the soft keys, you can switch func-
tions ON or OFF, or open submenus.
Example: Radio main menu:
The Scan soft key switches the scan
search ON or OFF.
The Autost. soft key opens the submenu
for the Autostore settings.
In some situations, soft keys may not have
any function and thus not be available.
Should a soft key not be available, it will
appear shaded out, its characters will ap-
pear white.
Example:
Presets, Scan and Autost. soft key.Exiting from submenus
You can exit the current submenu by
pressing the
Back soft key. The display
switches to the next higher menu level.
The system does not accept setting modi-
fications which have not been stored.
There are exceptions where pressing the
Back soft key will also store new settings.
These exceptions, whenever applicable,
are referenced on the following pages.
i
This information is also displayed in
Navigation* mode (only in map dis-
plays).

29 At a glance
Quick reference COMAND

Quick reference COMAND
Switching ON
Turn the key in the steering lock to po-
sition 1 or 2,
or
Press).
COMAND switches on the last active
system and displays the corresponding
menu.
Switching OFF
Turn the key in the steering lock to po-
sition 0 and remove it,
or
Press).Different volume settings are possible for
Navigation*, Telephone*, or Voice con-
trol*.
A common volume setting is provided for
Radio, Single CD, MP3, CD changer*, AUX
and Satellite radio* operating modes.
When setting the volume, the system auto-
matically stores the setting for the current-
ly active operating mode. The volume of
navigation announcements can be
changed only during an actual announce-
ment.
i
The system can be operated as follows:
from COMAND itself, or
from the multifunction steering
wheel
This operating manual describes oper-
ation from COMAND and from the mul-
tifunction steering wheel.
Unless otherwise specified, the de-
scriptions and the displays illustrated
relate to the COMAND control unit.
Switching ON/OFF
i
Without the key in position 1 or 2 of the
steering lock, the system automatically
switches OFF again after approx. 30
minutes of inactivity.
i
If a telephone call is in progress (hands-
free) you cannot switch the COMAND
OFF, ) is disabled.
Volume

31 At a glance
Quick reference COMAND
Setting balance/fader
Open the main menu of the appropriate
operating mode (
page 27).
Press the Bal/Fad soft key.
The Balance/Fader menu is displayed.
Now you can set the balance and the
fader (
page 31).
A cross-hair cursor appears. The verti-
cal line indicates the balance setting.
The horizontal line indicates the fader
setting.
Press# or $:
The cursor moves horizontally, adjust-
ing the desired balance,
or
Press% or &:
The cursor moves vertically, adjusting
the fader.
Storing new settings:
Press' or the Back soft key,
or
wait until the display changes.For the following operating modes, differ-
ent settings for bass and treble can be se-
lected:
Radio (FM waveband)
Radio (AM waveband)
Radio (Weather Band)
Single CD
MP3
CD changer*
AUX
Satellite radio*
Navigation*
Bass and treble settings for navigation an-
nouncements are found under “Adjusting
the acoustics for navigation announce-
ments” (
page 109).
i
Using 7 and 8, the cursor can be
moved simultaneously in vertical and
horizontal direction (diagonally).
Bass and treble

32 At a glance
Quick reference COMAND
When adjusting bass or treble, the system
automatically stores the setting for the
currently active operating mode.
Setting bass and treble
Open the main menu of the appropriate
operating mode (
page 27).
Press the Bass or Treble soft key.
The Bass or Treble menu appears.
Press# or $.
The cursor moves horizontally, adjust-
ing bass or treble accordingly.Storing new settings
Press' or the Back soft key,
or
wait until the display changes.
If the vehicle is equipped with a sound sys-
tem*, the sound functions are available for
the following operating modes:
Radio
Single CD
MP3
CD changer*
AUX
Satellite radio*The following sound functions are avail-
able:
Default Settings:
Resets the sound functions to the fac-
tory setting.
Standard:
Normal stereo playback.
Speech:
Playback optimized for speech compre-
hension.
LOGIC7 Surround:
7-channel-surround playback (not for
mono-sources like AM waveband or
Weather Band in radio mode).
Different sound functions can be activated
for each one of the operating modes listed
above.
Sound functions*

38 Audio
Radio operation
The following options are available:
Tuning via station search (page 38).
Tuning via station presets (page 39).
Tuning via Autostore presets
(
page 40).
Tuning via scan search (page 40).
Manual tuning (page 41).
Tuning via direct frequency input
(
page 41).
Tuning via station search
On COMAND control unit
Switch to the desired FM or AM wave-
band (
page 37).
Press+ or %:
The next receivable ascending frequen-
cy is tuned in and begins to play,
or
Press, or &:
The next receivable descending fre-
quency is tuned in and begins to play.
On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Radio display
(
page 25).
Pressj:
The next receivable ascending frequen-
cy is tuned in and begins to play,
or
i
The wavebands cover different fre-
quency ranges.
FM broadcast band:
FM (VHF = very high frequency)
87.7 - 107.9 MHz
Tuning increments 0.2 MHz
AM broadcast band:
MW (medium wave)
530 - 1710 kHz
Tuning increments 10 kHz
WB waveband:
WB (Weather Band)
162.400 - 162.550 MHz
Tuning increments = 1 channel
Tuning to a FM/AM station
i
Audio search function Freq. must be
set in the multifunction display
(
page 26).

39 Audio
Radio operation
Pressk:
The next receivable descending fre-
quency is tuned in and begins to play.
Tuning via station presets
Ten presets each are available for FM and
AM.
On COMAND control unit
The presets are accessed using the num-
ber keypad, or via the Presets menu.
Accessing via number keypad:
Switch to the desired waveband
(
page 37).
Press one of the number keys
! - ":
The system tunes to the station stored
under this number.
Accessing via Presets menu:
Switch to the desired waveband
(
page 37).
Press the Presets soft key.
The Presets menu appears.
Use $, #, % or & to choose a
preset and press',
or
Press one of the number keys
! - ".
The system tunes to the station stored
under this number.On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Radio display
(
page 25).
Pressj.
The system tunes to the next station
stored in the station presets;
or
Pressk.
The system tunes to the previous sta-
tion stored in the station presets.
i
Audio search function Memory must be
set in the multifunction display
(
page 26).

40 Audio
Radio operation
Tuning via Autostore presets
The Autostore function allows placing of
stations into the presets sorted by recep-
tion quality (
page 43).
The system will store the station with the
strongest signal in preset 1.
Ten presets each are available for FM and
AM.
Switch to the desired waveband
(
page 37).
Press the Autost. soft key.
The Autostore preset list appears. It
can take several seconds until all fre-
quencies are displayed.
Use $, #, % or & to choose a
preset and press'.
or
Press one of the number keys
! - ".
The system tunes to the station stored
under this number.Tuning via scan search
Scan search is characterized as follows:
Scan search performs two runs.
During the first run, stations with ex-
tremely good reception are played.
During the second run, stations with
weaker reception are played.
Scan search plays each receivable sta-
tion for approx. 8 seconds.
Scan search can be ended manually.
Scan search automatically stops at the
station listened to before the scan
search was started.
Starting scan search
Switch to the desired waveband
(
page 37).
Press the Scan soft key.
Scanning begins.

41 Audio
Radio operation
Ending Scan search manually
Press the Scan soft key again.
Manual tuning
Switch to the desired waveband
(
page 37).
Press and hold+ or , for at
least 2 seconds to tune up or down.
Manual tuning is activated.
Keep the button pressed or release it
and keep tapping+ or , in
quick succession.
The frequency will change by the tuning
increments for the respective wave-
band each time one of the buttons is
pressed or for as long as a button is
pressed and held.
Manual tuning is deactivated if no but-
ton is pressed for approx. 3 seconds. Tuning via direct frequency input
Entry example:
98.5 MHz in FM waveband
Switch to the FM waveband
(
page 37).
Press..
The frequency input display appears.
The frequency range of the FM wave-
band is shown.
i
Manual tuning is also possible in all
wavebands by pressing# or $.
The frequency will change by the tuning
increments for the respective wave-
band each time one of the buttons is
pressed.
Frequency increments for manual
tuning:
FM 0.2 MHz
AM 10 kHz