2007 MERCEDES-BENZ CLK63AMG headlamp

396 Practical hints
What to do if …?
Display symbolDisplay messagePossible cause/consequencePossible solution
I Keyless Go
Check systemThe KEYLESS-GO* system is malfunction-
ing.Contact an authorized Mercedes-Benz
Center as soon as possible.
Key detected
in vehicleA SmartKey with KEYLESS-GO* left in the
vehicle was recognized while locking the
vehicle from the outside.Take the SmartKey out of the vehicle.
Please do not
forget keyThis display appears (for a maximum of
60 seconds) if the driver’s door is opened
with the engine shut off and no SmartKey
in the starter switch.
Message is only a reminder.Insert SmartKey in the starter switch.
Take the SmartKey with
KEYLESS-GO* with you when leaving
the vehicle.
. Active headlamps
inoperativeThe Bi-Xenon cornering lamps system is
malfunctioning.Contact an authorized Mercedes-Benz
Center as soon as possible.
Active headlamps
Auxiliary bulb onThe active headlamps are malfunctioning.
Another light is being used.Contact an authorized Mercedes-Benz
Center as soon as possible.
AUTO-Light
inoperativeThe light sensor is malfunctioning. The
headlamps switch on automatically.In the control system, set lamp opera-
tion to manual mode (
page 160).
Switch on headlamps using the exteri-
or lamp switch.
Contact an authorized Mercedes-Benz
Center as soon as possible.

398 Practical hints
What to do if …?
Display symbolDisplay messagePossible cause/consequencePossible solution
. License plate lamp
left sideThe left license plate lamp is malfunction-
ing.Replace the bulb as soon as possible
(
page 433).
License plate lamp
right sideThe right license plate lamp is malfunc-
tioning.Replace the bulb as soon as possible
(
page 433).
Low beam
left sideThe left low beam lamp is malfunctioning.Halogen headlamp:
Replace the bulb as soon as possible
(
page 430).
Bi-Xenon* headlamp:
Contact an authorized Mercedes-Benz
Center as soon as possible.
Low beam
right sideThe right low beam lamp is malfunction-
ing.Halogen headlamp:
Replace the bulb as soon as possible
(
page 430).
Bi-Xenon* headlamp:
Contact an authorized Mercedes-Benz
Center as soon as possible.
Parking lamp
front left

The left front parking lamp is
malfunctioning. Replace the bulb as soon as possible
(
page 431).
Parking lamp
front right

The right front parking lamp is
malfunctioning.Replace the bulb as soon as possible
(
page 431).

399 Practical hints
What to do if …?
Display symbolDisplay messagePossible cause/consequencePossible solution
. Rear foglamp
Substitute bulb on

The foglamp is malfunctioning. A back-up
bulb is being used.Replace the bulb as soon as possible
(
page 432).
Reverse lamp
left sideThe left backup lamp is malfunctioning.Replace the bulb as soon as possible
(
page 432).
Reverse lamp
right sideThe right backup lamp is malfunctioning.Replace the bulb as soon as possible
(
page 432).
Side marker lamp
front leftThe front left side marker lamp is malfunc-
tioning.Contact an authorized Mercedes-Benz
Center as soon as possible.
Side marker lamp
front rightThe front right side marker lamp is mal-
functioning.Contact an authorized Mercedes-Benz
Center as soon as possible.
Tail lamp
left
Substitute bulb on

The left tail lamp is malfunctioning. A
back-up bulb is being used.Replace the bulb as soon as possible
(
page 432).
Tail lamp
right
Substitute bulb on

The right tail lamp is malfunctioning. A
back-up bulb is being used.Replace the bulb as soon as possible
(
page 432).
Turn off lampsYou have removed the SmartKey from the
starter switch, opened the driver’s door
and left the headlamps on or removed the
SmartKey with KEYLESS-GO* from the ve-
hicle and left the headlamps on.Switch off the headlamps.

427 Practical hints
Replacing bulbs
Replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp
assemblies are in good working order at all
times.Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See an authorized
Mercedes-Benz Center for headlamp
adjustment.iIf the headlamps or front fog lamps are
fogged up on the inside as a result of high
humidity, driving the vehicle a distance with the
lights on should clear up the fogging.
iBack-up bulbs will be brought into use when
lamps malfunction. Read and observe the
messages in the multifunction display
(
page 397).

428 Practical hints
Replacing bulbs
Bulbs Front lamps Rear lamps
LampType
1Additional turn signal
lampLED
2Turn signal lamp1156 NA
3Halogen headlamp:
Low beam
Bi-Xenon* headlamp:
Low and high beam
1
1Vehicles with Bi-Xenon headlamps* do not replace
the Bi-Xenon bulbs yourself.
H7 (55 W)
D2S-35 W
4Halogen headlamp:
High beam/high beam
flasher
Bi-Xenon* headlamp:
High beam flasher
H7 (55 W)
H7 (55 W)
Parking and standing
lampW 5 W
5Front fog lamp
Corner-illuminating
front fog lamp*HB4 (51 W)
H7 (55 W)
6Side marker lampW 5 W
LampType
7High mounted brake
lampLED
8Brake lampP 21 W
9Turn signal lampP 21 W
aTail, parking and stand-
ing lamp, side markerP 21/4 W
W 5 W
bBackup lampP 21 W
cLicense plate lampsC 5 W
dRear fog lamp
(driver’s side only)P 21/4 W

430 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 126).
Open the hood (page 315).
Front lamps halogen-type
1Housing cover for low beam headlamp
2Housing cover for high beam head-
lamp, parking and standing lamp3Bulb socket for turn signal lamp bulb
4Bulb holder of low beam bulb
5Bulb holder of high beam bulb
6Bulb socket for parking and standing
lamp bulb
Low beam bulb
Turn housing cover1 counterclock-
wise and remove it.
Turn bulb holder4 with the bulb coun-
terclockwise and remove it.
Pull the bulb at its socket out of bulb
holder4.
Insert the new bulb so that its socket
locates in the recess of bulb holder4
and is level to it.
Reinsert bulb holder4 with the bulb in
the lamp and turn clockwise.
Align housing cover1 and turn it
clockwise.
High beam bulb
Turn housing cover2 counterclock-
wise and remove it.
Turn bulb holder5 with the bulb coun-
terclockwise and remove it.
Pull the bulb at its socket out of bulb
holder5.
Insert the new bulb so that its socket
locates in the recess of bulb holder5
and is level to it.
Reinsert bulb holder5 with the bulb in
the lamp and turn clockwise.
Align housing cover2 and turn it
clockwise.

431 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Turn bulb socket3 counterclockwise
and remove it.
Press gently onto the bulb and turn
counterclockwise out of bulb
socket3.
Press the new bulb gently into bulb
socket3 and turn clockwise until it
engages.
Place bulb socket3 back into the
lamp and turn it clockwise.
Parking and standing lamp bulb
Turn housing cover2 counterclock-
wise and remove it.
Pull out bulb socket6 with the bulb.
Pull the bulb out of the bulb socket6.
Press the new bulb into bulb socket6.
Press bulb socket6 back into the
lamp.
Align housing cover2 and turn it
clockwise.Front lamps Bi-Xenon*-type
1Bulb socket for turn signal lamp
2Housing cover for high beam flasher,
parking and standing lamp
3Housing cover for Bi-Xenon* headlamp4Bulb holder for high beam flasher bulb
5Bulb socket for parking and standing
lamp bulb
High beam bulb for high beam flasher
Turn housing cover2 counterclock-
wise and remove it.
Turn bulb holder4 with the bulb coun-
terclockwise and remove it.
Pull the bulb at its socket out of bulb
holder4.
Insert the new bulb so that its socket
locates in the recess of bulb holder4
and is level to it.
Warning!G
Do not remove the cover 3 for the Bi-Xe-
non* headlamp. Because of high voltage in
Xenon lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.


451 Practical hints
Jump starting
The battery is located on the right side of
the engine compartment. For jump start-
ing, use the terminals in front of the bat-
tery.
Make sure the two vehicles do not
touch.
Turn off all electrical consumers.
Apply the parking brake (page 59).
Make sure the gear selector lever is set
to positionP (
page 172).
Open the hood (page 315).
Flip up cover from positive under hood
terminal2 in front of the filter box
(
page 448).1Positive terminal of charged battery
2Positive under hood terminal in front of
discharged battery
3Negative under hood terminal in front
of discharged battery
4Negative terminal of charged battery
Connect the positive terminal1 of the
charged battery with the positive under
hood terminal 2 in front of the filter
box with the jumper cable. Clamp cable
to charged battery1 first.
Start engine of the vehicle with the
charged battery and run at idle speed.
Connect the negative terminal4 of
the charged battery with the negative
under hood terminal 3 in front of the
filter box with the second jumper cable.
Clamp the cable to the negative
terminal4 of the charged battery
first.
Start the engine of the disabled vehi-
cle.
You can now turn on the electrical con-
sumers. Do not switch on the headlamps
under any circumstances.
Remove the jumper cables first from
the negative terminals3 and4 and
then from the positive terminals2
and1.
You can now switch on the headlamps.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.
!Never invert the terminal connections.