2007 MERCEDES-BENZ CLK550 COUPE garage door opener

Contents
Power windows .................................. 245
Opening and closing the windows 245
Synchronizing power windows ..... 247
Summer opening feature .............. 248
Convenience closing feature ........ 249
Power tilt/sliding sunroof* ................ 250
Opening and closing the
power tilt/sliding sunroof............. 250
Synchronizing the
power tilt/sliding sunroof............. 252
Driving systems ................................. 253
Cruise control............................... 253
Parktronic system
(Parking assist)*, Canada only ..... 257
Loading .............................................. 261
Roof rack ...................................... 261
Ski sack* (Canada only) ............... 262
Split rear bench seat .................... 264
Loading instructions ..................... 266
Cargo tie-down rings .................... 267Useful features .................................. 268
Storage compartments ................ 268
Center armrest ............................. 270
Armrest in the
rear passenger compartment ....... 271
Cup holders.................................. 271
Ashtrays ....................................... 272
Cigarette lighter ........................... 274
Power outlet in the
rear passenger compartment ....... 275
Floormats* ................................... 275
Telephone* .................................. 276
Tele Aid ........................................ 279
Garage door opener* ................... 285
Operation......................................... 291
The first 1 000 miles (1 500 km) ........ 292
Driving instructions ........................... 293
Drive sensibly – save fuel............. 293
Drinking and driving ..................... 293
Pedals .......................................... 293
Power assistance ......................... 294
Brakes.......................................... 294
Driving off .................................... 295
Parking......................................... 296
Tires ............................................. 296
Hydroplaning................................ 297
Tire traction ................................. 297
Tire speed rating .......................... 298
Winter driving instructions ........... 299
Standing water............................. 300
Passenger compartment .............. 300
Driving abroad ............................. 300
Control and operation
of radio transmitters .................... 300
Catalytic converter....................... 301
Emission control .......................... 302
Coolant temperature.................... 302

31 At a glance
Overhead control panel
Overhead control panel
ItemPage
1Rear interior lighting on/off137
2Power tilt/sliding sunroof* 250
3Right reading lamp on/off137
4Interior lighting control136
5Interior rear view mirror45,
179
6Garage door opener*285
7Hands-free microphone for
Tele Aid (emergency call
system) and telephone*276
8Left reading lamp on/off137
9Tele Aid (emergency call
system) button279

285 Controls in detail
Useful features
Stolen Vehicle Recovery services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered
incident report.
Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
Garage door opener*
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
iThe remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Con-
necting call
will appear in the multifunction
display to indicate receipt of the door unlock
command.
Once the vehicle is unlocked, a Response Center
specialist will attempt to establish voice contact
with the vehicle occupants.
If the trunk recessed handle was pulled for more
than 20 seconds before door unlock authoriza-
tion was received by the Response Center, you
must wait 15 minutes before pulling the trunk
recessed handle again.
iWhen the anti-theft alarm stays on for more
than 30 seconds, a call is initiated automatically
to the Response Center, see “Anti-theft alarm
system” (
page 94).

286 Controls in detail
Useful features
Interior rear view mirror with integrated re-
mote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
tonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 38).
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1 be-
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.

287 Controls in detail
Useful features
gins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:
Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.
Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

288 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.You have 30 seconds to initiate the
following step.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training
process.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.

290 Controls in detail
Useful features
Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.
iUSA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.

463 Index
Front passenger front air bag 65, 69
Messages in display 372–375
Front passenger front
air bag off indicator lamp 29, 74, 366
Front seat head restraints
see Head restraints
FSS (Canada vehicles) 343
Fuel 304, 449
Additives 452
Automatic transmission fluid 448
Brake fluid 448
Capacities 448
Capacities, Fuel tank 449
Engine coolant 449
Engine oil 448
Filling the tank 303
Fuel display 27
Fuel filler flap and cap 303
Fuel filler flap and cap, Multifunction
display messages 383
Fuel reserve warning lamp 363
Power steering fluid 448
Premium unleaded
gasoline 304, 449, 451
Requirements, Octane rating 451
Technical data 449Fuel cap
Message in display 360
Fuel consumption statistics
After start 163
Resetting 164
Since last reset 164
Fuel filler flap 303
Locking/unlocking 303
Opening 304
Fuel reserve warning lamp 27
Fuel tank
Capacity 449
Filler flap 303
Message in display 385
Fuel, Premium unleaded
gasoline 304, 449, 451
Fuels, coolants, lubricants etc.
Capacities 448
Fuses 431
Fuse box (main)
in passenger compartment 432
Fuse box
in engine compartment 433
Fuse box
in trunk 434
Replacing 431G
Garage door opener 31, 285
Gasoline see Fuel
GAWR 337
Gear range
Automatic transmission 173
Limiting 173
Shifting into optimal 176, 178
Gear selector lever 50, 168
Cleaning 353
Gearshift pattern 168
Lock 51
Message in display 376
Position 169, 170
Position indicator 141
Shifting procedure 169
Unlocking in an emergency 401
Gear selector lever one-touch gearshifting
Automatic transmission 175
Global locking/unlocking
see Key, SmartKey or KEYLESS-GO*