2007 MERCEDES-BENZ CL-CLASS parking brake

643 Practical hints
Replacing bulbs
Notes on bulb replacement
Only use 12-volt-bulbs of the same
type and with the specified watt rating.

Switch lights off before changing a bulb
to prevent short circuits.

Always use a clean lint-free cloth when
handling bulbs.

Your hands should be dry and free of oil
and grease.

If the newly installed bulb does not
come on, contact an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:

the Bi-Xenon lamps

the front turn signal lamps

the front fog lamps

the additional turn signal lamps in the
exterior rear view mirrors

the parking and standing lamps

the front side marker lamps

the high mounted brake lamps

the brake, tail and rear standing lamps

the rear side marker lamps

the rear fog lamp

the rear turn signal lamps

the rear side marker lamps

the license plate lamps
Warning!G
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot

drop the bulb

scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced by an autho-
rized Mercedes-Benz Center.
iHave the headlamp adjustment checked
regularly.
ProCarManuals.com

650 Practical hints
Flat tire
Preparing the vehicle
Prepare the vehicle as described
(
page 649).
Take vehicle tool kit and vehicle jack
out of trunk (
page 632).
Take the Minispare wheel and wheel
bolts out of the trunk (
page 634).Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
or other sizeable objects.
One wheel chock is included with the
vehicle tool kit (
page 634).
When changing wheel on a level surface:
Place the wheel chock in front of and
another sizeable suitable object behind
the wheel that is diagonally opposite to
the wheel being changed.
Always try lifting the vehicle using the jack
on a level surface. However, should cir-
cumstances require you to do so on a hill,
place the wheel chock and another size-
able suitable object as follows:
Place the wheel chock and another
sizeable suitable object on the downhill
side blocking both wheels of the axle
not being worked on.
Warning!G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always en-
gage the electronic parking brake and block
wheels before raising vehicle with jack.
Do not disengage electronic parking brake
while the vehicle is raised. Be certain that
the jack is always vertical (plumb line) when
in use, especially on hills. Always try to use
the jack on level surface. Make sure the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.
ProCarManuals.com

657 Practical hints
Batteries
Starter battery (example illustration from
CL 550)
1Negative terminal
2Positive terminal
Disconnecting starter battery
Secure vehicle in place with electronic
parking brake (
page 384).
Shift the automatic transmission toP
(
page 389).
Do not rub the battery with rags or cloths.
The battery could explode if touched due to
electrostatic charge or due to spark forma-
tion.
!Switch off the engine and switch off the ve-
hicle’s internal electrical functions (
page 658)
before you disconnect or remove the battery’s
terminal clamps. You could otherwise destroy
electronic assemblies such as the generator.
Have the battery checked regularly by an autho-
rized Mercedes-Benz Center. Refer to Mainte-
nance Booklet for maintenance intervals or
contact an authorized Mercedes-Benz Center for
further information.
!Do not connect any consumers directly to
the starter battery. The starter battery will other-
wise be discharged.
iOnly replace a discharged battery with a bat-
tery recommended by Mercedes-Benz. The con-
sumer battery is installed in the trunk in such a
way that it is safeguarded as much as possible
against mechanical destruction in the event of
an accident.
iRemove SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the vehicle’s
on-board electronics have status 0)
(
page 336) when you turn off the engine and
no longer require any electrical consumers. The
vehicle then uses very little power and the con-
sumer battery is spared.
iIf the consumer battery is discharged, you
must use the mechanical key to unlock the vehi-
cle (
page 635). Since the vehicle has a sepa-
rate starter battery, however, you can still start
the vehicle.
!Always disconnect the starter battery in the
order described below. You could otherwise
damage the vehicle’s electronics.
!Switch off the vehicle’s internal electrical
functions before disconnecting the starter bat-
tery. If the vehicle is stationary for more than one
hour with the SmartKey removed, you do not
need to switch off the vehicle’s internal electrical
functions.
ProCarManuals.com

661 Practical hints
Jump starting
Jump starting should only be performed on
the starter battery. The starter battery is
located in the engine compartment on the
passenger side (
page 657).
Make sure the two vehicles do not
touch.
Secure vehicle in place with electronic
parking brake (
page 384).
Shift the automatic transmission toP
(
page 389).
Turn off all electrical consumers, ex-
cept hazard warning flashers or work
lights.
Open the hood (page 512).
Start the engine of the vehicle with the
charged battery and run at idle speed.1Negative clamp
2Negative terminal of charged battery
3Positive terminal of charged battery
4Positive terminal of discharged battery
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 655).
iVehicles with KEYLESS-GO: remove the
KEYLESS-GO button (
page 337) and use the
SmartKey with KEYLESS-GO like a normal
SmartKey.

ProCarManuals.com

664 Practical hints
Towing the vehicle
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle. Adapt your driving accordingly.
!When towing the vehicle with all wheels on
the ground or with the front axle raised, the start-
er battery must be connected and charged. Oth-
erwise:

you will not be able to switch on the ignition

you will not be able to engage the automatic
transmission in positionN (
page 394)

you cannot release the electronic parking
brake
For information on charging the starter battery
see “Batteries” (
page 655) or see “Jump start-
ing” (
page 660).
!Make sure that the electronic parking brake
is released. If the electronic parking brake is
malfunctioning, release it mechanically
(
page 637).
!If the vehicle is towed with the front axle
raised, the automatic transmission must be in
positionN and the engine must be shut off
(SmartKey or SmartKey with KEYLESS-GO* in
starter switch position0 or1). Active braking
action through the ESP
® may otherwise
seriously damage the brake system.
!When towing the vehicle with all wheels on
the ground, the automatic transmission must be
shifted to positionN and the SmartKey or
SmartKey with KEYLESS-GO* must be in starter
switch position2.
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle may
be towed only for distances up to 30 miles
(50 km) and at a speed not to exceed 30 mph
(50 km/h).
!If the vehicle is towed with all wheels on the
ground or with the front axle raised, the trans-
mission must be in positionN.
If you turn off the engine using

the SmartKey and

remove the SmartKey from the starter
switch
or

open a door

the KEYLESS-GO* start/stop button and
open a door
the transmission will shift to park position P
automatically.
ProCarManuals.com

665 Practical hints
Towing the vehicle
If you want the gear position to remain in
neutral position N, observe the following
instructions.
Vehicles with SmartKey:
With the vehicle at a standstill and the
ignition switched on shift the
automatic transmission to neutral
positionN.
If engaged, manually release the elec-
tronic parking brake (
page 385).
Switch off the ignition and leave the
SmartKey in the starter switch.Vehicles with KEYLESS-GO*:
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.
With the ignition switched on shift the
automatic transmission to park
positionP.
Release the brake pedal.
Remove the KEYLESS-GO start/stop
button from the starter switch
(
page 337).
Insert the SmartKey with KEYLESS-GO
into the starter switch.
Switch on the ignition.
Depress the brake pedal.
Shift the automatic transmission to
neutral positionN.
Release the brake pedal.
If engaged, manually release the
electronic parking brake (
page 385).
Switch off the ignition and leave the
SmartKey with KEYLESS-GO in the
starter switch.
Warning!G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment. Unsupervised use
of vehicle equipment could result in an
accident and/or serious personal injury.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey or SmartKey with KEYLESS-GO* in
starter switch position 2, the vehicle doors lock
if the left front wheel as well as the right rear
wheel are turning at vehicle speeds of approxi-
mately 9mph (15km/h) or more.
To prevent the vehicle doors from locking,
deactivate the automatic central locking
(
page 334).
iTo signal turns while being towed with the
hazard warning flasher in use, turn SmartKey or
SmartKey with KEYLESS-GO* in starter switch to
position2 and activate the combination switch
for the left or right turn signal in the usual
manner – only the selected turn signal will
operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
ProCarManuals.com

667 Practical hints
Fuses
Fuses
The electrical fuses in your vehicle serve to
switch off malfunctioning power circuits.
If a fuse is blown, the component(s) and
systems secured by that fuse will stop op-
erating.
If a newly inserted fuse blows again, have
the cause determined and rectified by an
authorized Mercedes-Benz Center.
The following aids are available to help you
replace fuses. They are located in the trunk
with the vehicle tool kit (
page 632):

Fuse chart
The fuse chart explains the fuse alloca-
tion and fuse amperages.

Spare fuses

Special fuse extractor
The electrical fuses are located in different
fuse boxes:

in the dashboard on the passenger side
(
page 669)

in the dashboard on the driver’s side
(
page 669)

behind the rear center armrest
(
page 669)

on the driver’s side of the engine com-
partment (
page 668)

on the passenger side of the engine
compartment (
page 668)
Before replacing fuses:
Engage the electronic parking brake
(
page 384).
Make sure the automatic transmission
is set to P (
page 389).
The gear position indicator in the ta-
chometer display should be on P.
Turn off all electrical consumers.
Turn off the engine (page 387).
Switch off the vehicle’s internal electri-
cal functions (
page 658).
Warning!G
Only use fuses approved by Mercedes-Benz
with the specified amperage for the system
in question and do not attempt to repair or
bridge a blown fuse. Using other than ap-
proved fuses or using repaired or bridged
fuses may cause an overload leading to a
fire, and/or cause damage to electrical
components and/or systems. Have the
cause determined and remedied by an
authorized Mercedes-Benz Center.
!Switch off the vehicle’s internal electrical
functions (
page 658) when you are working on
the fuses.
iA blown fuse must be replaced by an appro-
priate spare fuse (recognizable by its color or the
fuse rating given on the fuse) of the amperage
recommended in the fuse chart.
Any Mercedes-Benz Center will be glad to advise
you on this subject.
ProCarManuals.com

695 Index
B
Backup lamps
Replacing bulbs 642
Bar 545
BAS 66
Batteries, SmartKey
Checking battery condition 332
Replacing 639
Batteries, SmartKey with KEYLESS-GO*
Checking battery condition 332
Replacing 639
Batteries, vehicle 655
Charging 658
Discharged, Jump starting 660
Disconnecting 657
For electrical consumers 655
For starter 655
Message in display 608
Reconnecting 659
Removing 658
Bead 545
Beverage holder see Cup holder
Bluetooth
®
Settings (COMAND) 232
Brake assist system (BAS Plus) 67
Brake assist system (BAS) 66Brake fluid 511, 685, 687
Brake lamp bulbs 642
Brake lamp, high mounted 642
Brake pads
Message in display 598
Brake warning lamp 31
Brakes 500
Warning lamp 31, 567
Break-in period 498
Bulbs, replacing 641
Additional turn signals 642
Brake lamps 642
Fog lamps 642
Front lamps 642
High beam 642
High mounted brake lamp 642
License plate lamps 642
Low beam 642
Parking and standing lamps 642
Rear fog lamp 642
Turn signal lamps 642C
California retail buyers and lessees,
important notice for 15
Can holder see Cup holder
Capacities and
recommended fuel/lubricants 684
Carpets, Cleaning and care of 564
Catalytic converter 507
CD
Ejecting (COMAND) 113
Loading (COMAND) 111
Menu overview (COMAND) 114
Playback options (COMAND) 119
Selecting a medium (COMAND) 117
Selecting a track (COMAND) 117
CD (COMAND) 107
Central locking
Automatic 334
Locking/unlocking from inside 335
Central locking/unlocking switches 335
Certification label 674
Change of address or ownership 16
ProCarManuals.com