2007 MERCEDES-BENZ C280 technical data

396 Technical data
The “Technical data” section provides the
necessary technical data for your vehicle.
Parts service
All authorized Mercedes-Benz Centers
maintain a stock of Genuine
Mercedes-Benz parts required for mainte-
nance and repair work. In addition, strate-
gically located parts distribution centers
provide quick and reliable parts service.
More than 300 000 different parts for
Mercedes-Benz models are available.
Genuine Mercedes-Benz parts are subject
to stringent quality inspections. Each part
has been specifically developed, manufac-
tured or selected for and adapted to
Mercedes-Benz vehicles.
Therefore, Genuine Mercedes-Benz parts
should be installed.!The use of non-genuine Mercedes-Benz
parts and accessories not authorized by
Mercedes-Benz could damage the vehicle, which
is not covered by the Mercedes-Benz Limited
Warranty, or could compromise the vehicle’s
durability or safety.

397 Technical data
Warranty coverage
Warranty coverage
Your vehicle is covered under the terms of
the warranties printed in the Service and
Warranty Information booklet. Your
authorized Mercedes-Benz Center will ex-
change or repair any defective parts origi-
nally installed in the vehicle in accordance
with the terms of the following warranties:

New Vehicle Limited Warranty

Emission System Warranty

Emission Performance Warranty

California, Maine, Massachusetts, and
Vermont Emission Control Systems
WarrantyReplacement parts and accessories are
covered by the Mercedes-Benz Parts and
Accessories warranties, copies of which
are available at any Mercedes-Benz
Center.Loss of Service and Warranty
Information Booklet
Should you lose your Service and Warranty
Information booklet, have an authorized
Mercedes-Benz Center arrange for a
replacement. It will be mailed to you.

398 Technical data
Identification labels
1Certification label (on driver’s B-pillar)
The V
ehicle Identification Number (VIN)
can be found in the following locations:

on the certification label.

embossed underneath the carpet in
front of the front passenger seat
(
page 399).

on the lower edge of the windshield
(
page 399).
Example certification label (U.S. vehicles)
2VIN
3Paintwork code
Example certification label
(Canada vehicles)
2VIN
3Paintwork code
iData shown on certification label are for
illustration purpose only. These data are specific
to each vehicle and may vary from data shown in
the illustration. Refer to certification label on
vehicle for actual data specific to your vehicle.

399 Technical data
Identification labels
4Carpet
5VIN
Move the front passenger seat to the
rear as far as possible.
Fold carpet4 in direction of arrow.
VIN5 is visible.6Emission control information label,
includes both federal and California
certification exhaust emission
standards
7Vacuum line routing diagram label
8Engine number (engraved on engine)
9VIN (lower edge of windshield)
iWhen ordering parts, please specify vehicle
identification and engine numbers.

400 Technical data
Layout of poly-V-belt drive
All models
1Idler pulley
2Idler pulley
3Automatic belt tensioner
4Power steering pump
5Air conditioning compressor
6Crankshaft
7Coolant pump
8Generator (alternator)

401 Technical data
Engine
Engine
ModelC 230 (203.052)1
C 230 Sport (203.052)1
1The quoted data apply only to the standard vehicle. See an authorized Mercedes-Benz Center for the corresponding data of all special bodies and special equipment.
C 280 (203.054)1
C 280 4MATIC (203.092)1
Engine272272
Mode of operation4-stroke engine, gasoline injection4-stroke engine, gasoline injection
No. of cylinders66
Bore3.46 in (88.00 mm)3.46 in (88.00 mm)
Stroke2.69 in (68.40 mm)3.23 in (82.10 mm)
Total piston displacement152.3 cu in (2 496 cm3)182.8 cu in (2 996 cm3)
Compression ratio11.2:111.3:1
Output acc.
to SAE J 1349201 hp/6 200 rpm2
(150 kW/6 200 rpm)
2Premium fuel required. Performance may vary with fuel octane rating.
228 hp/6 000 rpm2
(170 kW/6 000 rpm)
Maximum torque acc.
to SAE J 1349181 lb-ft/2 700 – 5 500 rpm
(245 Nm/2 700 – 5 500 rpm)221 lb-ft/2 700 – 5 000 rpm
(300 Nm/2 700 – 5 000 rpm)
Maximum engine speed6500 rpm6500 rpm
Firing order1-4-3-6-2-51-4-3-6-2-5
Poly-V-belt2404 mm2404 mm

402 Technical data
Engine
ModelC 350 (203.056)1
C 350 Sport (203.056)1
C 350 4MATIC (203.087)1
Engine272
Mode of operation4-stroke engine, gasoline injection
No. of cylinders6
Bore3.65 in (92.90 mm)
Stroke3.38 in (86.00 mm)
Total piston displacement213.5 cu in (3 498 cm3)
Compression ratio10.7:1
Output acc.
to SAE J 1349268 hp/6 000 rpm2
(200 kW/6 000 rpm)
Maximum torque acc.
to SAE J 1349258 lb-ft/2 400 – 5 000 rpm
(350 Nm/2 400 – 5 000 rpm)
Maximum engine speed6 500 rpm
Firing order1-4-3-6-2-5
Poly-V-belt2 404 mm
1The quoted data apply only to the standard vehicle. See an authorized Mercedes-Benz Center for the
corresponding data of all special bodies and special equipment.
2Premium fuel required. Performance may vary with fuel octane rating.

403 Technical data
Rims and Tires
Rims and Tires
!Only use tires which have been tested and
approved for your vehicle by Mercedes-Benz.
Tires approved by Mercedes-Benz are developed
to provide best possible performance in conjunc-
tion with the driving safety systems on your vehi-
cle such as ABS or ESP
®. Tires specially
developed for your vehicle and tested and ap-
proved by Mercedes-Benz can be identified by
finding the following on the tire’s sidewall:

MO = Mercedes-Benz Original equipment
tires

MOE = Mercedes-Benz Original Extended
(tires with limited run-flat characteristics)
original equipment tires. Using tires other
than those approved by Mercedes-Benz may
result in damage that is not covered by the
Mercedes-Benz Limited Warranty.
iFor information on driving with MOExtended
tires, see “MOExtended system*” (
page 382).
!Using tires other than those approved by
Mercedes-Benz can have detrimental effects,
such as

poor handling characteristics

increased noise

increased fuel consumption
Moreover, tires and rims not approved by
Mercedes-Benz may, under load, exhibit dimen-
sional variations and different tire deformation
characteristics that could cause them to come
into contact with the vehicle body or axle parts.
Damage to the tires or the vehicle may be the
result.
iFurther information on tires and rims is
available at any authorized Mercedes-Benz
Center. A placard with the recommended tire in-
flation pressures is located on the driver’s door
B-pillar. Some vehicles may have supplemental
tire inflation pressure information for driving at
high speeds (
page 290) or for vehicle loads
less than the maximum loaded vehicle condition
(
page 290). If such information is provided, it can be found
on the placard located on the inside of the fuel
filler flap. The tire inflation pressure should be
checked regularly and should only be adjusted
on cold tires. Follow tire manufacturer’s mainte-
nance recommendation included with vehicle.
iThe following pages also list the approved
wheel rim and tire sizes for equipping your vehi-
cles with winter tires. Winter tires are not avail-
able as standard or optional factory equipment,
but can be purchased from an authorized
Mercedes-Benz Center.
Depending on vehicle model and the standard or
optional factory-equipped wheel rim/tire config-
uration on your vehicle (Appearance Package,
Sport Package etc.), equipping your vehicle with
winter tires approved for your vehicle model may
also require the purchase of two or four wheel
rims of the recommended size for use with these
winter tires. See an authorized Mercedes-Benz
Center for more information.