2007 MAZDA MODEL CX-7 low beam

Black plate (193,1)
Signal Warning/Indicator Lights Page
Seat Belt Warning Light/Beep 5-41
Door-Ajar Warning Light 5-43
Low Washer Fluid Level Warning Light 5-43
Automatic Transaxle Warning Light 5-43
AWD Warning Light 5-43
Tire Pressure Monitoring System Warning Light 5-44
KEY Warning Light (Red)/KEY Indicator Light (Green) 5-45
Security Indicator Light 5-47
Headlight High-Beam Indicator Light 5-47
Shift Position Indicator Light 5-47
TCS/DSC Indicator Light 5-48
TCS OFF Indicator Light 5-48
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 5-49
Light-On Indicator Light 5-49
Turn Signal/Hazard Warning Indicator Lights 5-49
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-37
CX-7_8V28-EA-06B_Edition2 Page193
Monday, March 13 2006 5:6 PM
Form No.8V28-EA-06B

Black plate (203,1)
NOTE
The advanced key can be set so that the
KEY indicator light (green) does not
flash even if the battery power is low.
Refer to Setting Change (Function
Customization)(page 3-20).
qSecurity Indicator Light
This indicator light starts flashing every 2
seconds when the ignition switch is turned
from the ON to the ACC position and the
immobilizer system is armed.
The light stops flashing when the ignition
switch is turned to the ON position with
the correct ignition key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then goes out.
If the engine doesn't start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
qHeadlight High-Beam Indicator
Light
This light indicates one of two things:
lThe high-beam headlights are on.
lThe turn signal lever is in the flash-to-
pass position.
qShift Position Indicator Light
This indicates the selected shift position
when the ignition switch is in the ON
position.
Gear position indicator
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-47
CX-7_8V28-EA-06B_Edition2 Page203
Monday, March 13 2006 5:6 PM
Form No.8V28-EA-06B

Black plate (209,1)
CAUTION
Do not shade the light sensor by
adhering a sticker or a label on the
windshield, or putting an object on it.
Otherwise the light sensor will not
operate correctly.
Sensor
NOTE
lWhen the headlight switch is in the
AUTO position and the ignition
switch is turned to the ACC or
LOCK position, the headlights, other
exterior lights and dashboard
illumination will turn off.
lThe timing for turning on the
headlights, other exterior lights and
dashboard illumination can be
delayed by adjusting the sensitivity
of the light sensor. Consult an
Authorized Mazda Dealer regarding
sensor adjustment.
Xenon fusion headlight bulbsí
The low-beam bulbs of the headlights
have xenon fusion bulbs that produce a
bright white beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement is
necessary.
NOTE
If the headlights flash, or the brightness
weakens, the bulb-life may be depleted
and a replacement is necessary. Consult
an Authorized Mazda Dealer.
qLights-On Reminder
If lights are on and the key is removed
from the ignition switch, a continuous
beep sound will be heard when the
driver's door is opened.
NOTE
When the advanced keyless function is
used and the start knob is in the ACC
position, the“Start Knob Not in LOCK
Warning Beep”(page 3-17) overrides
the lights-on reminder.
Driving Your Mazda
Switches and Controls
5-53íSome models. CX-7_8V28-EA-06B_Edition2 Page209
Monday, March 13 2006 5:6 PM
Form No.8V28-EA-06B

Black plate (210,1)
qHeadlight High-Low Beam
Push the lever forward for high beam.
Pull back to original position for low
beam.
High beam
Low beam
qFlashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch does
not need to be on, and the lever will return
to the normal position when released.
qHeadlight Levelingí
The number of riders and weight of cargo
in the luggage compartment change the
angle of the headlights.
The headlight leveling switch adjusts this
angle.
Select the proper setting from the following chart.
Front seat
Rear
seatLoadSwitch
Position
Driver Passenger
×―――0
××――0
×× ×―1
×× ×× 2
×――×3
×: Yes
―:No
qDaytime Running Lights (Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
NOTE
The Daytime Running Lights turn off
when the parking brake is applied.
5-54
Driving Your Mazda
íSome models.
Switches and Controls
CX-7_8V28-EA-06B_Edition2 Page210
Monday, March 13 2006 5:6 PM
Form No.8V28-EA-06B

Black plate (329,1)
Light Bulbs
Headlights (Low beam) Headlights (High beam)
High-mount brake lightFog lights
Front turn signal lights/Parking lights
Some models.
License plate lights
Brake lights/Taillights Overhead light/Map lights (Front) Overhead light (Rear)
Front side marker lights
Rear turn signal lights
Rear side marker lights
Reverse lights
Luggage compartment light
Maintenance and Care
Owner Maintenance
8-33
CX-7_8V28-EA-06B_Edition2 Page329
Monday, March 13 2006 5:7 PM
Form No.8V28-EA-06B

Black plate (331,1)
NOTE
lTo replace the bulb, contact an
Authorized Mazda Dealer.
lIf the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
lUse the protective cover and carton
of the replacement bulb to dispose of
the old bulb promptly out of the
reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
1. Make sure the headlight switch is off.
2. If you are changing the right Low-
beam bulb, start the engine, turn the
steering wheel all the way to the right,
and turn off engine. If you are
changing the left Low-beam bulb, turn
the steering wheel to the left.3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Detach the electrical connector from
the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.
Maintenance and Care
Owner Maintenance
8-35
CX-7_8V28-EA-06B_Edition2 Page331
Monday, March 13 2006 5:7 PM
Form No.8V28-EA-06B

Black plate (339,1)
DESCRIPTION FUSE RATING PROTECTED COMPONENT
19 DEF 30A Rear window defroster
20 TNS 15AParking lights, License plate lights,
Illuminated entry system
21 A/C 10A Air conditioner
í
22 ETC 20A Accelerator position sensor
23 H/L HI 15A Headlight levelingí
24 DRL 15A DRLí
25 H/L LO RH 15A Headlight low beam (RH)
26 H/L LO LH 15A Headlight low beam (LH)
27 ENG BAR 2 7.5A PCM
28 ECM 10A Engine control system
29 ENG BAR 1 15A Air flow sensor, EGR control valve
30 P.WIND 2 20A Power windows
31 STOP 10A Brake lights
32 HORN 20A Horn
33 ENG B+ 25A PCM
34 HAZARD 10A Hazard warning flashers, Turn signals
Fuse block (Driver's side)
DESCRIPTION FUSE RATING PROTECTED COMPONENT
1 OUTLET 1 15A Accessory Socket
Maintenance and Care
Owner Maintenance
8-43íSome models. CX-7_8V28-EA-06B_Edition2 Page339
Monday, March 13 2006 5:8 PM
Form No.8V28-EA-06B

Black plate (396,1)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage ECE R (SAE)
HeadlightsHigh beam 60 HB3 (#9005)
Low beamHalogen 55 H7 (H7)
Xenon fusion 35 D2S (―)
Front turn signal lights/Parking lights 27/8―(#1157NA)
Front side-marker lights 5 W5W (#168)
Fog lights
í55 H11 (H11)
High-mount brake light*12.4―(―)
Rear turn signal lights 21 WY21W (―)
Brake lights/Taillights 21/5 W21/5W (#7743)
Reverse lights 21 W21W (#7440)
License plate lights 5 W5W (#168)
Rear side-marker lights 5 W5W (#168)
*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
Interior light
Light bulbCategory
Wattage ECE R
Overhead lights/Map lights (Front) 5 W5W
Overhead light (Rear) 10―
Luggage compartment light 10―
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type
originally fitted to your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation pressure.
Refer to Tire Inflation Pressure on page 8-28.
Standard tire
Tire sizeInflation pressure
Front Rear
P235/60R18 102H 220 kPa (32 psi) 220 kPa (32 psi)
10-6íSome models.
Specifications
CX-7_8V28-EA-06B_Edition2 Page396
Monday, March 13 2006 5:8 PM
Form No.8V28-EA-06B