JOBNAME: No Job Name PAGE: 262 SESS: 1 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
2. If driven in hot weather, city traffic, pulling a trailer, allow
transmission to cool for 30 minutes before checking.
3. Engage parking brake, start engine.
4. Put your foot on the brake pedal and move the gearshift lever slowly
through all of the gear ranges.
5. Shift to P (Park) and leave the engine running.
6. Remove the dipstick, wipe clean with a dry lint free rag.
7. Install and fully seat the dipstick into the filler tube.
8. Remove the dipstick and inspect
the fluid level. Level should be
in the cross-hatched area.
9. If necessary, add fluid in 1/2 pint (250ml) increments through the
filler tube until the level is correct at normal operating temperatures.
Refer to theMaintenance product specifications and capacities
section in this chapter for the correct fluid type. The use of any
other non-approved fluid may cause internal transmission damage.
10. Fluid can be checked at ambient
temperatures between 50±95ÉF
(10±30ÉC). DO NOT ADD fluid
until the transmission is at
normal operating temperatures or the transmission will be overfilled.
Low fluid level
Do not drive the vehicle if the fluid
level is at or below the bottom of
the dipstick.
High fluid level
Fluid levels above the safe range
may cause overheating, shift and/or
engagement concerns and internal
transmission damage. If an overfill
condition occurs, excess fluid should
be removed by an authorized dealer.
CIMS #953919
com_trans-level.fly
itdseq=317
art=ranmc130_a
art=ranmc131_a
art=ranmc129_b
art=ranmc132_a
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:262OP:rootEDIT SESSION:1DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Maintenance and Specifications
262
JOBNAME: No Job Name PAGE: 263 SESS: 1 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
Checking and adding manual transmission fluid (if equipped)
1. Park the vehicle on a level
surface.
2. Engage the parking brake fully ±
put in first gear.
3. Ensure that the vehicle cannot
move.
4. Clean the filler plug.
5. Remove the filler plug and
inspect the fluid level.
6. Fluid level should be at the
bottom of the opening.
7. Add enough fluid through the
filler opening so that the fluid
level is at the bottom of the
opening.
8. Install and tighten the fill plug
securely.
Use only fluid that meets Mazda specifications. Refer to the
Maintenance product specifications and capacitiessection in this
chapter.CIMS #1126961
com_chk-man-trans.maz
itdseq=318
art=mbsmc002_a
art=f23mc115_a
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:263OP:rootEDIT SESSION:1DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Maintenance and Specifications
263
JOBNAME: No Job Name PAGE: 264 SESS: 1 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
TRANSFER CASE FLUID (IF EQUIPPED)
1. Park the vehicle on a level
surface.
2. Engage the parking brake fully ±
put in first gear.
3. Ensure the vehicle cannot move.
4. Clean the filler plug.
5. Remove the filler plug and
inspect the fluid level.
6. Fluid level should be at the
bottom of the opening.
7. Add enough fluid through the
filler opening so that the fluid
level is at the bottom of the
opening.
8. Install and tighten the fill plug
securely.
Use only fluid that meets Mazda specifications. Refer to the
Maintenance product specifications and capacitiessection in this
chapter.
DRIVELINE UNIVERSAL JOINT AND SLIP YOKE
Your vehicle may be equipped with universal joints that require
lubrication. If the original universal joints are replaced with universal
joints equipped with grease fittings, lubrication will also be necessary.CIMS #918861
com_check-add-tcase.mbs
itdseq=319
CIMS #918862
com_serv-shaft-yoke.mbs
itdseq=320
art=ranmc128_d
art=f12mc022_a
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:264OP:rootEDIT SESSION:1DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Maintenance and Specifications
264
JOBNAME: No Job Name PAGE: 265 SESS: 1 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
CHECKING AND ADDING REAR DIFFERENTIAL FLUID
1. Park the vehicle on a level
surface.
2. Engage the parking brake fully ±
put in first gear.
3. Assure the vehicle cannot move.
4. Clean the filler plug.
5. Remove the filler plug and
inspect the fluid level.
6. Fluid level should be at the
bottom of the opening.
7. Add enough fluid through the
filler opening so that the fluid
level is at the bottom of the
opening.
8. Install and tighten the fill plug
securely.
Use only fluid that meets Mazda specifications. Refer to the
Maintenance product specifications and capacitiessection in this
chapter.
art=mbsmc003_a
art=f12mc022_a
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:265OP:rootEDIT SESSION:1DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Maintenance and Specifications
265
JOBNAME: No Job Name PAGE: 266 SESS: 1 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES
Item ApplicationMazda part name or
equivalentCapacity
Brake fluid and clutch
fluid (if equipped)AllHigh Performance DOT 3
Motor Vehicle Brake
FluidBetween MIN and MAX
on reservoir
1
Door weather strips All Silicone Lubricant Ð
Hinges, door checks,
latches, striker plates,
fuel filler door hinge
and seat tracksAll Multi-Purpose Grease Ð
Transmission
/steering/parking brake
linkages and pivots,
brake and clutch pedal
shaft, clutch pilot
bearing and input shaft
spline (manual
transmission)AllPremium Long-Life
GreaseÐ
CIMS #1541546
com_lubes-caps.mbs
itdseq=321
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:266OP:rootEDIT SESSION:1DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Maintenance and Specifications
266
JOBNAME: No Job Name PAGE: 269 SESS: 1 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
Item ApplicationMazda part name or
equivalentCapacity
Fuel tankRegular cab
(Short wheel
base)Ð17 gallons (64.4L)
Cab Plus 4 19.5 gallons (73.8L)
1Brake fluid will drop slowly as the brakes wear and will rise when brake components are replaced.
Fluid levels below the MAX line that do not trigger the brake warning light are within the normal
operating range, there is no need to add fluid. If the levels are outside the normal operating range,
the performance of your brake system could be compromised, seek service from your authorized
dealer immediately.2Add the coolant type originally equipped in your vehicle. Do not mix different colors or types of
coolant. Do not use Mazda Extended Life Engine Coolant (orange in color). Refer toAdding
engine coolant, in this chapter.3Service refill capacity is determined by filling the transmission to the bottom of the filler hole with
the vehicle on a level surface.4Automatic transmissions that require MERCONtV should only use MERCONtV fluid or fluid that
is specified dual usage MERCONt/ MERCONtV. Refer toscheduled maintenanceto determine
the correct service interval. Use of any fluid other than the recommended fluid may cause
transmission damage.5Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and
if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set
by the indication on the dipstick's normal operating range.6Traction-Lok axles use 4.75±5.0 pints (2.2±2.4L) of rear axle lubricant. Add 4 oz. (118 ml) of
Additive Friction Modifier meeting Mazda specifications for complete refill of Traction-Lok axles.
Service refill capacities are determined by filling the rear axle 1/4 inch to 9/16 inch (6 mm to 14
mm) below the bottom of the filler hole.
If submerged in water, the rear axle lubricant should be changed.
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:269OP:rootEDIT SESSION:1DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Maintenance and Specifications
269
JOBNAME: No Job Name PAGE: 275 SESS: 3 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
A
ABS (see Brakes) .....................158
Airbag supplemental restraint
system ..........................................91
and child safety seats ..............94
description ................................91
disposal ......................................96
driver airbag ........................91, 94
indicator light ...........................95
operation .............................91, 94
passenger airbag .................91, 94
Ambulance packages ....................7
Antifreeze (see Engine
coolant) .....................................242
Anti-lock brake system (see
Brakes) ..............................158±159
Anti-theft system ........................70
Audio system
Single CD ..................................21
Audio system (see Radio) ..19, 21,
24, 29, 32
Automatic transmission ............162
driving an automatic
overdrive .................................163
fluid, specification ..................266
Auxiliary Input Jack ...................37
Auxiliary power point .................58
Axle
lubricant specifications ..........266
traction lok ..............................161
B
Battery .......................................240
acid, treating emergencies .....240
jumping a disabled battery ....196
maintenance-free ....................240servicing ..................................240
BeltMindert.................................86
Brakes ........................................158
anti-lock ...........................158±159
anti-lock brake system (ABS)
warning light ...........................159
fluid, checking and adding ....260
fluid, specifications .................266
lubricant specifications ..........266
parking ....................................160
shift interlock ..........................162
Break-in period .............................5
Bulbs ............................................50
C
Cargo cage ...................................63
Cell phone warning ...................274
Changing a tire .........................186
Child safety restraints ..............100
child safety belts ....................100
Child safety seats ......................103
attaching with tether straps ..107
in front seat ............................104
in rear seat ..............................104
tether anchorage hardware ...107
Chimes (warning) .......................17
Cleaning your vehicle
engine compartment ..............215
instrument panel ....................218
interior .....................................218
interior trim ............................218
Mazda car care products .......219
plastic parts ............................217
washing ....................................214
waxing .....................................214
wheels ......................................215
wiper blades ............................217
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:275OP:rootEDIT SESSION:3DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Index
275
JOBNAME: No Job Name PAGE: 278 SESS: 3 OUTPUT: Thu Aug 3 11:45:36 2006
/ford_pdm/ford/own2002/mbs/og
lubricant specifications ..........266
reverse .....................................167
Mirrors .........................................60
fold away ...................................60
side view mirrors (power) .......60
Motorcraft parts ........................247
O
Octane rating ............................251
Oil (see Engine oil) ..................234
Overdrive .....................................63
Overheating ...............................195
P
Parking brake ............................160
Passenger Occupant
Classification Sensor ...................77
Power distribution box (see
Fuses) ........................................180
Power door locks ........................66
Power mirrors .............................60
Power point .................................58
Power steering ..........................161
fluid, checking and adding ....259
fluid, specifications .................266
Power Windows ...........................59
Preparing to drive your vehicle 161
R
Radio ....................19, 21, 24, 29, 32
Single CD ..................................21
Relays ........................................176
Remote entry system .................67
illuminated entry ......................69locking/unlocking doors ...........67
panic alarm ...............................67
replacing the batteries .............67
S
Safety Belt Maintenance ............84
Safety belts (see Safety
restraints) ........................75, 79±83
Safety restraints ..............75, 79±83
BeltMindert..............................86
extension assembly ..................84
for adults .............................80±82
for children .......................99±100
Occupant Classification
Sensor ........................................77
safety belt maintenance ...........84
warning light and chime ..........85
Safety restraints - tether
anchors ......................................107
Safety seats for children ..........103
Safety Compliance
Certification Label ....................272
Satellite Radio Information ........39
Seat belts (see Safety
restraints) ....................................75
Seats ............................................73
child safety seats ....................103
SecuriLock passive anti-theft
system ..........................................70
Servicing your vehicle ..............228
Setting the clock
AM/FM stereo ...........................19
AM/FM stereo CD ...............21, 24
Premium AM/FM stereo
CD6/MP3 .............................29, 33
Snowplowing .................................7
Spark plugs, specifications .......270
REVIEW COPY ÐÐ
2007 B-Series(mbs), Owners Guide (post-2002-fmt)(own2002),Market:USA(fus)
PAGE:278OP:rootEDIT SESSION:3DATE:AUG 3 2006 at 11:45JOB:@ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_mbs/DIV_og
Index
278