2007 MAZDA MODEL 6 HATCHBACK lights

GETTING STARTED
Always check the Owner’s Manual for more operating information and safety features
Getting
Started
Getting
Started
Cruise
control
Operates
above
19 mph
To activate:
Press and release ON/OFF (1)
To set speed: Press and release
SET/COAST (3) at desired speed
To accelerate: Press and hold
RES/ACCEL (2); incremental
acceleration: Press and release
(2), each tap = plus 1 mph
To decelerate: Press and hold SET/
COAST (3), release at desired speed;
or tap brake pedal, press and release
(3) at desired speed; incremental
deceleration: Press and release
(3), each tap = minus 1 mph
To cancel: Tap brake pedal, clutch
pedal (manual transaxle) or press
CANCEL button (4) or ON/OFF (1)
Return to preset speed after
Remote keyless entry systemFunctions only with key removed
from ignition switch
To lock doors: Press button (1);
press again within 5 seconds,
doors relock and horn beeps
To unlock: Press (2) for driver’s
door; press again within 5 seconds to
unlock other doors, press and hold
for 3 seconds to lower front windows
To open trunk: Press (4)
Panic alarm: Press (3); horn
sounds; to stop, press any button
on the transmitter or turn ignition
to ON position
Tilt/telescopic
steering-wheel
lever
Pull lever (5)
down to unlock
column, adjust tilt
angle and length
of steering column
WARNING: Do not adjust
steering-wheel while driving
Instrument panel
lighting
To brighten/dim turn
thumbwheel up/down
HID headlights
leveling switch
Set position at 0 unless
vehicle is loaded heavily,
leveling switch adjusts
headlight angle to compensate
for weight of passengers and
cargo, see Owner’s Manual
Remote window operationRemote keyless entry: Press unlock
button (2) and hold, doors/liftgate
unlock and windows fully open
Key: Insert key in driver’s door
lock; turn toward front/rear of
vehicle and hold it, after doors/
liftgate are unlocked/locked
windows will open/close
ClockTo set: With ignition in ACC or
ON position, press (A) and hold
until beep sounds; 12 hr/24hr
will be displayed; press (B) to
select; press (A) again while
selection is flashing: Hr ADJUST
displays; press (B) to select hr;
press (A) when done, do the
same to set minutes
1243
123
5
10111413
9B AC
12
Sedan 5-Door/
Sport Wagon
10
Rear center position seat belt†
Pull seat belt (9) from recess located
in ceiling (A) (Sport Wagon),
behind head restraint (B) (Sedan) or
left side of cargo area (C) (5-Door):
Slide tongues with finger while pulling
Fastening seat belt: Tongue (10)
and anchor (11) must be fastened,
then slowly pull out lap/shoulder
belt (12) and insert tongue (13)
into buckle (14) until click is heard
Unfastening seat belt: Depress
buckle button to release
Stowing seat belt: Retract belt, put
tongues (10) and (13) together, insert
securely into recess (A,Bor C) CANCELbutton or braking: Press
and release RES/ACCEL button (2)
Tip: Cruise control will not
be canceled in Manual Mode
during gear changes
Steering-
wheel
audio
controls
To increase/decrease
volume: Press (5)
Radio: Press (6) less than one
second to select next/previous
preset station, press (6) more
than one second until beep sound
is heard to seek next/previous station
Cassette/CD: Press (6) to select
next selection/track, press (6) to
repeat current selection/track
Press (7) to select AM, FM 1,
FM 2, Cassette* and CD mode
Press (8) to mute Audio/NAVI system*
/
/
M
O
D
EV
O
L5
678
RES
ACCEL ON
OFF
CANCELSET
COAST43
12
*Denotes optional equipment†See Owner’s Manual
CLOCK
SETABTILT
SET CLKAB

INSTRUMENT CLUSTER
Always check the Owner’s Manual for more operating information and safety features
Instrument
Cluster
Instrument
Cluster
HF
E C
P
R
N
D
M
2
12213121411
0 123x1000r/min
4
5
6
7
8
19202221232518246
8
109
4
15
17
16
0 20mph
km/h4060
80
100
120
140
TRIPA8
O.O
20 406080100120
140
160
180
200
220
240
75
3
17. Low fuel
18. Brake system
Parking brake on/low fluid level
19. Check engine
Dealer inspection required
20. Charging system
warning light
Dealer inspection required
21. Engine oil pressure
warning light
22. Air bag readiness
Front, side and/or curtain air bag
malfunction; warning light
constantly flashes or stays on
or never comes on with ignition
on, dealer inspection required
23. Door ajar
24. Immobilizer system on,
see Locks
25. Always fasten
safety belts
8. Engine coolant
temperature gauge
If above normal range, stop
vehicle and turn off engine,
check coolant level when safe
12. Automatic transaxle
indicator
Dealer inspection required
if light remains on
13. High beams on
14. Traction Control
System (TCS)
Light flashes when in use;
dealer inspection required if
light remains on
Enhances traction and safety
by regulating engine torque
When TCS detects drive wheel
slippage it lowers engine torque
to prevent loss of traction
15. Lights on*
16. Traction Control
System off
System turned off manually
or malfunctioning; dealer
inspection required7. Odometer/tripmeter
selector
Press to select among trip A,
trip B, and odometer
Press and hold to reset selected
trip meter
WARNING LIGHTS
9. Cruise control,see Getting Started
10. Cruise Control Main
Power On,see Getting Started
11. Anti-lock Brake
System (ABS)
ABS malfunction, normal brakes
only, dealer inspection required
ABS automatically reduces
hydraulic pressure to any wheel
on the verge of locking up
You may feel a slight pulsing of
the brake pedal and hear a
clicking noise; this tells you the
ABS is functioning properly;
increase pressure on pedal for
maximum braking
Tips: Maintain constant
pressure on the brake pedal
Do not pump the brakes
CRUISE
MAIN
CRUISE
GAUGES
1. Tachometer
2. Turn signals/hazard
warning on
3. Speedometer
4. Fuel gauge
5. Odometer/tripmeter
6. Gear indicator
Displays current gear of Sport AT
*If equipped with black-out meter

DRIVER CONTROLS
Always check the Owner’s Manual for more operating information and safety features
Driver
Controls
Switches
12
Turn signals right/left: Move lever
up/down
= Fog lights on: Rotate knob
(2); functions only with headlight
low beams on
Tip: Headlights switch off auto-
matically within 30 seconds if
lights are left on and switch is
in lock position or key removed
Wiper/washer control lever
Intermittent wiper: One click down
To change interval speed:
Rotate inner ring (3)
Normal wiper speed: Two
clicks down
Fast wiper speed: Three
clicks down
Single wipe: Push stalk up
Washer: Pull stalk back
Rear window wiper/washer
(5-Door/Sport Wagon)
To activate rear interval wiper:
Rotate knob (4) up to INT
To activate rear normal speed
wiper: Rotate knob (4) up to ON
To activate rear washer with
wipers operating: Rotate knob
(4) up to ; hold knob (4)
to continue washing; release
knob and wipers will continue
to operate
To operate stand alone wipe/
wash function: Rotate knob
(4) down and hold, release
to stop
Front window switches
One-touch down/up: Press/pull
AUTO switch (3) firmly and
release, window goes down/up
all the way, press/pull briefly
to stop, press/pull lightly and
hold for normal operation
Tip: During closing window
operation, window will stop
and open partway if object
blocks window operation
Rear window switches
Push/pull (4) to open/close
Power window lockout switch
Press button (5), only driver's
window operates; press again
for normal operation
Power window
initialization procedure
If battery is disconnected or power
window fuse is replaced, the auto
open/close and anti-pinch features
will not functionResetting procedure:
1. Turn ignition switch
to “ON” position
2. Make sure that power
window lock switch located
on driver’s door is not
depressed
3. Press switch and fully open
power window
4. Pull up switch to fully close
power window and continue
holding switch for about
2 seconds after window
fully closes
5. Repeat steps 3- 4 for front
passenger power window
while seated in front
passenger seat
6. Make sure power windows
operate correctly using
door switches
Dual power
mirrors
Ignition switch
must be in ACC
or ON position
Switch is on
driver’s door
To adjust left/right mirror:
Press selector switch (1) left/
right, press switch (2) in direction
of desired movement
Tip: To lock mirrors in place,
move selector switch (1) to
center position
Power window
switches
With ignition ON
All windows
controlled from
driver’s armrest;
passenger doors
have separate
switches
Turn signal/lighting
control lever
OFF= Lights off
= Tail, parking and
dashboard lights on: Rotate
knob (1) to first notch
= Tail, parking, dashboard
and headlights on: Rotate knob
(1) to second notch
High beams on/off: Push lever
forward/pull back to detent
To flash high beams: Pull lever
back slightly and release
34
R
E
A
R
543
AU
TOA
U
TO
LR
2
1

HOMELINK®
Always check the Owner’s Manual for more operating information and safety features
HomeLink®
Interior
Lights
Auto-dimming rear
view mirror*
Auto-dimming function changes
are based on outside lighting
conditions and if bright headlights
are visible in rear view mirror
Press on (2), off (3)
5. Moonroof tilt switch
Press rear of switch to
tilt rear of moonroof
Press front of switch to close
6. Moonroof slide switch
Press rear of switch to open
moonroof
Press front of switch to close
Illuminated visor mirrors
Mirrors lighted when covers
open; off when closed Rolling code synchronization
procedure
Refer to your garage door opener or
device instruction manual to confirm
your system is equipped with a
rolling code feature
Tip: This procedure is easier
to perform with the assistance
of another person
To synchronize: Press programming
button on garage door opener
motor; press/hold for 2 seconds
and release the programmed
HomeLink
®button 2 times
within 30 seconds of pressing
the garage door opening
motor programming button
Some devices may require you
to press/hold and release a
third time to complete
programming procedure
If indicator light stays on,
programming is complete
To erase all existing programming;
press and hold two outer
HomeLink
®buttons (1) on mirror,
continue to hold buttons until
indicator light flashes
1. Map/reading light switch
Press on/off
2. Interior light switch
DOOR = light on when
door open
OFF = light always off
3. Interior map/reading
light
4. Sunglass holder
Press concaved lip to open
To program or reprogram:
Press and hold two outer
HomeLink
®buttons (1) for 20
seconds and no more than
30 seconds, release only after
indicator light (4) begins to
flash; hold transmitter for the
device to be programmed
between 1-3 inches to
HomeLink
®; press transmitter
button and desired HomeLink®
button (1) simultaneously until
HomeLink®indicator light (4)
goes from slow to rapid flashing
Verify device operation by
pressing HomeLink
®button (1)
that was just programmed
Tip: You do not need to repeat
the first step to program the
other two hand-held transmit-
ters for the remaining
HomeLink® buttons
For further information, contact
HomeLink
®at 1-800-355-3515,
www.homelink.comor your
authorized Mazda Dealer HomeLink
®Wireless
Control System*
Located on rear view mirror
HomeLink
®provides three
programmable buttons that
will replace three hand-held
device transmitters
Tip: It is recommended to
park outside of garage when
programming HomeLink
®
WARNING: When programming
a garage door or gate opener,
disconnect power to these
devices before programming,
continuous operation of these
devices could damage the motor
*Denotes optional equipment
11423
T
I
L
TSL
ID
E
121
43356
OFFDOO
R

UNDER HOOD
Always check the Owner’s Manual for more operating information and safety features
Under Hood
1. Engine oil filler cap
SAE 5W-20
2. Automatic transmission
fluid (ATF) dipstick
See Owner’s Manual
3 . Brake/Clutch* fluid reservoir
Fill to MAX mark with DOT 3
fluid; check with cap on
4. Battery
5. Fuse block
6. Air filter
7. Hood support rod
8. Hood latch
Push hood latch to the right,
open hood
9. Engine coolant reservoir
Level should be between FULL
and LOW markings when cold
WARNING: Never remove
coolant reserve tank cap
while engine is running or
hot; you could get burned
10. Engine oil dipstick
Check with engine off after
approximately 5 minutes and
at operating temperature; fluid
level should be between MAX
and MIN markings on dipstick
11. Power steering fluid
reservoir
Check with engine off and at
normal temperature; fill to
MAX mark
12. Windshield washer
reservoir
Fill with windshield washer fluid
Gas cap
After filling vehicle with gasoline,
fully reinstall gas cap by turning
clockwise until a clicking sound is
heard, if gas cap is not fully installed,
Check Engine light may come on
For more information on
Check Engine light, see
Owner’s Manual
Break-in period
First 600 miles: Drive at varying
road and engine speeds; avoid
full throttle, rapid acceleration
or kick-down of transmission
Unique driving conditions
†Every 5,000 miles change
oil/filter, inspect coolant level,
lights, brake/clutch fluid, tire
pressure/wear, power steering
fluid, locks/hinges and washer fluid
Normal maintenance notes
Rotate tires every 7,500 miles or
sooner if needed
Replace cabin air filter every
25,000 miles or 24 months
Inspect exhaust system and heat
shields every 45,000 miles
Replace (FL22) engine coolant
every 120,000 miles or 10 years
WARNING: Using coolant other
than FL22 requires more frequent
maintenance intervals
A.Change: Engine oil/
replace filter
Lube: Locks and hinges
B.Inspect: Disc brakes
C.Inspect: Drive belts (3.0 liter),
fuel lines and hoses, brake
lines, hoses and connections,
steering operation and linkages,
front and rear suspension ball
joints, driveshaft dust boots,
cooling system
D.Inspect: Drive belts (2.3 liter)
Replace: Air filter
E.Inspect: Hoses and tubes for
emission system
F. Replace: Spark plugs
Inspect: Engine valve clearance
(2.3 liter), adjust if noisy
G. Replace: Engine coolant
(Other than FL22)
3.0-liter V62.3-liter I4
*Denotes optional equipment†See Owner’s Manual
1197126
5143
810
101179126
51243
8
7,500 miles
15,000 miles
22,500 miles
30,000 miles
37,500 miles
45,000 miles
52,500 miles
60,000 miles
67,500 miles
75,000 miles
82,500 miles
90,000 miles
A A A
F A A
B C E A A
B A D A
BC A
A B A
105,000 miles G