2007 MAZDA MODEL 5 maintenance

Black plate (280,1)
3. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulb)
1. Disconnect the electrical connector from the bulb by pulling it to the rear.
2. Pull off the sealing cover. 3. Unhook the bulb retaining spring.
4. Swing the retaining spring out and
away to free the headlight bulb.
5. Carefully remove the socket and bulb assembly by pulling it straight back.
6. Remove the headlight bulb from the socket.
7. Install the new socket and bulbassembly in the reverse order of
removal.
8-38
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page280
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (281,1)
NOTElIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
lWhen reinstalling the sealing cover, make
sure
faces up.
Replacing a front fog light bulbsí
1. Remove the three screws under themudguard by turning them
counterclockwise, and partially open
the mudguard.
2. Turn the socket and bulb assemblycounterclockwise, and carefully pull it
rearward. 3. Disconnect the socket and bulb
assembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
4. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Maintenance and Care
Owner Maintenance
8-39íSome models.
Mazda5_8X91-EA-07E_Edition1 Page281
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (282,1)
Front turn signal lights/Side-marker
lights
1. Turn the center section of the plasticretainers counterclockwise and remove
them, then partially peel back the
mudguard.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Remove the bulb by pushing it in slightly and turning it
counterclockwise.
4. Install the new bulb in the reverse orderof removal.
Side turn signal lights
1. Slide the unit as shown in the figure toremove it. 2. Disconnect the electrical connector
from the unit.
3. Install the new side turn signal unit in
the reverse order of removal.
NOTE
Bulb replacement is not possible because it is
built into the unit. Replace the unit.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Wrap a flathead screwdriver with a soft cloth to prevent damage to the rear
combination component and gently
insert it in the cover as shown in the
figure, and then remove the cover.
2. Remove the screws with a Phillipsscrewdriver and remove the rear
combination component.
8-40
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page282
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (283,1)
3. Turn the socket and bulb assemblycounterclockwise and remove it.
4. Disconnect the bulb from the socket.
Reverse lights
Rear turn signal lights
Brake lights/Taillights
5. Install the new bulb in the reverse order of removal.
License plate lights
1. Remove the liftgate cover.
2. Pull the socket and bulb assembly andremove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assemblycounterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-41
Mazda5_8X91-EA-07E_Edition1 Page283
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (284,1)
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse orderof removal.
Overhead light (Rear)
1. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Luggage compartment light
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the trim and
gently insert it in the luggage
compartment light as shown in the
figure, and then remove the luggage
compartment light unit.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
8-42
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page284
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (285,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the passenger's
side
If the electrical system doesn't work, first
inspect fuses on the passenger's side.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.
CAUTION
Pulling the cover off sideways may
break the retaining tabs off. 3. Locate the position of the suspected
fuse by using the chart inside the fuse
block cover.
4. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
5. Inspect the fuse and replace it if it'sblown.
Normal Blown
6. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an expert
repairer install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
Maintenance and Care
Owner Maintenance
8-43
Mazda5_8X91-EA-07E_Edition1 Page285
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (286,1)
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and allother switches.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
Main fuse
8-44
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page286
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (287,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FAN 30 A Cooling fan
2 FAN 30 A Cooling fan
3 P.WIND 40 A ―
4 IG KEY1 30 A ―
5 ABS-V 20 A ABS
6 ABS-P 30 A ABS
7 IG KEY2 20 A For protection of various circuits
8 HEATER
DEICER 20 A
―
9 BLOWER 40 A Blower motor
10 GLOW
IG KEY1 40 A For protection of various circuits
11 BTN 40 A For protection of various circuits
12 IG KEY2 40 A ―
13 CLOSER
P.SLIDE LH 20 A Easy closer (LH)
í
14CLOSER
P.SLIDE RH 20 A Easy closer (RH)í
Maintenance and Care
Owner Maintenance
8-45íSome models.
Mazda5_8X91-EA-07E_Edition1 Page287
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E