Page 280 of 409

Black plate (281,1)
NOTElIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
lWhen reinstalling the sealing cover, make
sure
faces up.
Replacing a front fog light bulbsí
1. Remove the three screws under themudguard by turning them
counterclockwise, and partially open
the mudguard.
2. Turn the socket and bulb assemblycounterclockwise, and carefully pull it
rearward. 3. Disconnect the socket and bulb
assembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
4. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Maintenance and Care
Owner Maintenance
8-39íSome models.
Mazda5_8X91-EA-07E_Edition1 Page281
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 281 of 409

Black plate (282,1)
Front turn signal lights/Side-marker
lights
1. Turn the center section of the plasticretainers counterclockwise and remove
them, then partially peel back the
mudguard.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Remove the bulb by pushing it in slightly and turning it
counterclockwise.
4. Install the new bulb in the reverse orderof removal.
Side turn signal lights
1. Slide the unit as shown in the figure toremove it. 2. Disconnect the electrical connector
from the unit.
3. Install the new side turn signal unit in
the reverse order of removal.
NOTE
Bulb replacement is not possible because it is
built into the unit. Replace the unit.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Wrap a flathead screwdriver with a soft cloth to prevent damage to the rear
combination component and gently
insert it in the cover as shown in the
figure, and then remove the cover.
2. Remove the screws with a Phillipsscrewdriver and remove the rear
combination component.
8-40
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page282
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 282 of 409
Black plate (283,1)
3. Turn the socket and bulb assemblycounterclockwise and remove it.
4. Disconnect the bulb from the socket.
Reverse lights
Rear turn signal lights
Brake lights/Taillights
5. Install the new bulb in the reverse order of removal.
License plate lights
1. Remove the liftgate cover.
2. Pull the socket and bulb assembly andremove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assemblycounterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-41
Mazda5_8X91-EA-07E_Edition1 Page283
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 283 of 409
Black plate (284,1)
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse orderof removal.
Overhead light (Rear)
1. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Luggage compartment light
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the trim and
gently insert it in the luggage
compartment light as shown in the
figure, and then remove the luggage
compartment light unit.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
8-42
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page284
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 284 of 409

Black plate (285,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the passenger's
side
If the electrical system doesn't work, first
inspect fuses on the passenger's side.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.
CAUTION
Pulling the cover off sideways may
break the retaining tabs off. 3. Locate the position of the suspected
fuse by using the chart inside the fuse
block cover.
4. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
5. Inspect the fuse and replace it if it'sblown.
Normal Blown
6. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an expert
repairer install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
Maintenance and Care
Owner Maintenance
8-43
Mazda5_8X91-EA-07E_Edition1 Page285
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 285 of 409

Black plate (286,1)
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and allother switches.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
Main fuse
8-44
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page286
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 287 of 409

Black plate (288,1)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
15 EHPAS 80 A EHPAS
16 FOG 15 A Front fog lights
í
17 D.LOCK 20 A Power door lock
18 P.WIND
H/CLEAN 20 A
―
19 MAG 10 A Magnet clutch
20 DEFOG 25 A Rear window defroster
21 ENG+B 10 A PCM
22 STOP 10 A Brake lights
23 FUEL 20 A Fuel pump
24 HAZARD 10 A Turn signals, Hazard warning flashers
25 ROOM 15 AOverhead lights, Map lights, Luggage compartment light, For
protection of various circuits
26 ―― ―
27 ―― ―
28 GLOW SIG 7.5 A ―
29 HEAD HR 10 A Headlight high beam (RH)
30 HEAD HL 10 A Headlight high beam (LH)
31 HORN 15 A Horn
32 SUN ROOF 20 A Moonroof
í
33 ETC MIRROR
BURGLAR 7.5 A PCM
34 HEAD LR 15 A Headlight low beam (RH), Manual headlight leveling
í
35 HEAD LL 15 A Headlight low beam (LH)
36 ENG BAR2 15 A PCM
37 ENG BAR 15 A Air flow sensor, Engine control system
38 INJ 20 A Injector
39 ILLUMI 10 A Illumination
40 TAIL 10 A Taillights, Parking lights, License plate lights, For protection of
various circuits
8-46
Maintenance and Care
íSome models.
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page288
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E
Page 292 of 409

Black plate (293,1)
CAUTION
ØDon't use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or
caustic agents on chrome-plated
or anodized aluminum parts. This
may damage the protective
coating; also, cleaners and
detergents may discolor or
deteriorate the paint.
Ø To prevent damaging the antenna,
remove it before entering a car
wash facility or passing beneath a
low overhead clearance.
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don't allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Dry wet brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal: Driving with wet brakes is
dangerous. Increased stopping
distance or the vehicle pulling to one
side when braking could result in a
serious accident. Light braking will
indicate whether the brakes have
been affected.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for metallic, mica, and solid colors.
3. When waxing, coat evenly with the sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and similar
materials will usually also take off the wax.
Rewax these areas even if the rest of the
vehicle doesn't need it.
Maintenance and Care
Appearance Care
8-51
Mazda5_8X91-EA-07E_Edition1 Page293
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E