2007 ISUZU KB P190 wheel

3C-12 FRONT SUSPENSION
4. Install link nut, then tighten it to the specified
torque.
Torque: 50 N ⋅
⋅⋅
⋅
m (5.1 kgf ⋅
⋅⋅
⋅
m/37 lb ⋅ft)
5. Tighten the cam bolt and lower control arm nut, setting it to the interim torque, then turn the cam
bolt to the setting mark applied during
disassembly.
6. Install ball joint nut, then tighten it to the specified torque with just enough additional torque to align
cotter pin holes. Install new cotter pin.
Torque: 147 N ⋅
⋅⋅
⋅
m (15.0 kgf ⋅
⋅⋅
⋅
m/108 lb ⋅ft)

NOTE: Check the trim height. Refer to Front Alignment
Inspection and Adjustment.

7. Lower control arm nut tightens it to the specified torque.
Buffer clearance: 25.9 mm (1.02 in)
Torque: 186 N ⋅
⋅⋅
⋅
m (19.0 kgf ⋅
⋅⋅
⋅
m/137 lb ⋅ft)

NOTE: Apply oil to the thread.
NOTE: Tighten the bolt and nut with the parts in the
position shown in the illustration below.



















RTW 53ASH000201
8. Install wheel and tire assembly. Refer to wheel in
this section.




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3C-16 FRONT SUSPENSION
Stabilizer Bar
Stabilizer Bar and Associated Parts



RTW 340LF000901
Legend
(1) Stabilizer Bar
(2) Link
(3) Link Nut

(4) Link Nut
(5) Bracket and Bolt
(6) Rubber Bushing


Removal
1. Raise the vehicle and support the frame with
suitable safety stands.
2. Remove wheel and tire assembly. Refer to W heel Replacement in this section.

3. Remove link nut.
CAUTION: Be careful not to damage the ball joint
boot.
4. Remove link.
5. Remove bracket and bolt.
6. Remove stabilizer bar.
7. Remove rubber bushing.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3C-18 FRONT SUSPENSION
Knuckle
Knuckle and Associated Parts



450R300037
Legend
(1) Nut and Cotter Pin
(2) Back Plate
(3) Nut and Cotter Pin

(4) Nut and Cotter Pin
(5) Knuckle
(6) Bolt


Removal
1. Raise the vehicle and support the frame with
suitable safety stands.
2. Remove wheel and tire assembly. Refer to W heel in this section.

3. Remove the brake caliper. Refer to Disc Brakes in
Brake section.
4. Remove the hub assembly. Refer to Front Hub and Disk in this section.
5. Remove tie-rod end from the knuckle. Refer to Power Steering Unit in Steering section.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT SUSPENSION 3C-19
6. Remove the stabilizer link nuts. Right and left.
7. Remove the wheel speed sensor from the knuckle.
8. Remove back plate.
9. Remove lower ball joint by using remover 5-8840- 2017-0.
CAUTION: Be careful not to damage the ball joint
boot.

P1010009
10. Remove upper ball joint by using remover 5-8840-2017-0.
CAUTION: Be careful not to damage the ball joint
boot.

P1010011
11. Remove knuckle.

Inspection and Repair
Make the necessary adjustments or parts replacement
if wear, damage, corrosion or any other abnormal
condition is found during inspection.
Check the following parts:
• Knuckle
• Knuckle arm
Installation
1. Install knuckle assembly.
2. Install upper ball joint and tighten the nut to the specified torque, with just enough additional torque
to align cotter pin holes. Install new cotter pin.
Torque: 98 N ⋅
⋅⋅
⋅
m (10.0 kgf ⋅
⋅⋅
⋅
m/72 lb ⋅ft)
3. Install lower ball joint and tighten the nut to the specified torque, with just enough additional torque
to align cotter pin holes. Install new cotter pin.
Torque: 147 N ⋅
⋅⋅
⋅
m (15.0 kgf ⋅
⋅⋅
⋅
m/108 lb ⋅ft)
4. Install back plate.
5. Install wheel speed sensor.
6. Install stabilizer link nut. Right and left.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3C-20 FRONT SUSPENSION
Upper Control Arm
Upper Control Arm and Associated Parts



450R300038
Legend
(1) Upper Control Arm Bolt
(2) Bushing
(3) Upper Control Arm Nut
(4) Upper Control Arm Assembly
(5) Upper Ball Joint
(6) Nut and Cotter Pin

(7) Knuckle
(8) Link Nut
(9) Upper Ball Joint Nut
(10) Upper Ball Joint Bolt
(11) Speed Sensor Harness Nut
(12) Brake Fluid Hose Nut

Removal
1. Raise the vehicle and support the frame with
suitable safety stands.
2. Remove wheel and tire assembly. Refer to W heel
in this section.
3. Remove speed sensor harness nut.
4. Remove brake fluid hose nut.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3C-22 FRONT SUSPENSION
Lower Control Arm
Lower Control Arm and Associated Parts
RTW 340LF002301
Legend
(1) Cam bolt
(2) Bush
(3) Cam plate
(4) Lower Control Arm Nut
(5) Shock Absorber Nut

(6) Lower Ball Joint Bolt
(7) Lower Ball Joint
(8) Nut and cotter pin
(9) Lower Ball Joint Nut
(10) Link Nut
(11) Shock Absorber Bolt


Removal
1. Raise the vehicle and support the frame with suitable safety stands.
2. Remove wheel and tire assembly. Refer to W heel
in this section.
3. Remove the tie-rod end from the knuckle. Refer to Power Steering Unit in Steering section.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3C-24 FRONT SUSPENSION
Upper Ball Joint
Upper Ball Joint and Associated Parts



RTW 340LF001101
Legend
(1) Upper Ball Joint Bolt
(2) Upper Ball Joint

(3) Upper Ball Joint Nut
(4) Nut and Cotter Pin
(5) Link Nut


Removal
1. Raise the vehicle and support the frame with suitable safety stands.
2. Remove wheel and tire assembly. Refer to wheel in this section.
3. Remove link nut.

4. Remove upper ball joint nut and cotter pin, then
use remover 5-8840-2017-0 to remove the uppe
r
ball joint from the knuckle.
CAUTION: Be careful not to damage the ball joint
boot and brake hose.




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3C-26 FRONT SUSPENSION
Lower Ball Joint
Lower Ball Joint and Associated Parts




RTW 340LF002201
Legend
(1) Lower Ball Joint
(2) Nut and Cotter Pin

(3) Lower Ball Joint Nut
(4) Link Nut
(5) Lower Ball Joint Bolt


Removal
1. Raise the vehicle and support the frame with suitable safety stands.
2. Remove wheel and tire assembly. Refer to W heel in this section.
3. Remove the link nut.
4. Support lower control arm with a jack.
5. Remove lower ball joint nut and cotter pin, then
use remover 5-8840-2017-0 to remove the lowe
r
ball joint from the knuckle.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007