2007 ISUZU KB P190 lock

3A-8 FRONT ALIGNMENT




Toe-in Adjustment
Measurement should be taken with the vehicle on a surface
plate.
If a surface plate is not available, toe-in should be checked
with the vehicle parked on a level floor.
1. Set front wheels to straight ahead position.
2. Align the toe-in gauge with center height of each wheel at front end.
3.
Apply center marks to each wheel, then take measurement
of distance A between the center marks on each wheel.
4. Slowly move the vehicle rearward until the center marks reach the rear end position.
5. Take measurement of distance B between the cente
r
marks at rear end.
The toe-in can be calculated with the following formula.
Toe-in = B - A
Toe-in mm (in)
4×2
(Except high ride suspension) 0
±2 (0 ±0.08)





To adjust the toe-in angle, loosen the lock nuts (2) on the tie
rod (1) and turn the tie rod. Turn both rods the same amount,
to keep the steering wheel centered.
Lock Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
98 ±6.0 (10.0 ±0.6 / 72.3 ±4.3)



RTW 53ASH000101

Trim Height
Trim Height : at Curb Weight (Reference Data)
Trim height (Z) = A - B
Front mm (in)
Z
105(4.13)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3A-12 FRONT ALIGNMENT





Toe-in Adjustment
Measurement should be taken with the vehicle on a surface
plate.
If a surface plate is not available, toe-in should be checked
with the vehicle parked on a level floor.
1. Set front wheels to straight ahead position.
2. Align the toe-in gauge with center height of each wheel at front end.
3.
Apply center marks to each wheel, then take measurement
of distance A between the center marks on each wheel.
4. Slowly move the vehicle rearward until the center marks reach the rear end position.
5. Take measurement of distance B between the cente
r
marks at rear end.
The toe-in can be calculated with the following formula.
Toe-in = B - A
Toe-in mm (in)
4×2 (High ride suspension)
4×4 0
±2 (0 ±0.08)






To adjust the toe-in angle, loosen the lock nuts (2) on the tie
rod (1) and turn the tie rod. Turn both rods the same amount,
to keep the steering wheel centered.
Lock Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
98 ±6.0 (10.0 ±0.6 / 72.3 ±4.3)

RTW 330SH000201

Trim Height
Trim Height : at Curb Weight
Trim height (Z) = A - B
mm (in)
Z
165±5 (6.5 ±0.20) (Philippine only)
140 ±5 (5.5 ±0.20) (Except Philippine)


MAXIMUM STEERING ANGLE
4
×2 (High ride suspension), 4 ×4
Outside wheel 32.8° (Philippine only)
Inside wheel 35.0° (Philippine only)
Outside wheel 32.1° (Except Philippine)
Inside wheel 34.4° (Except Philippine)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-2 POWER-ASSISTED STEERING SYSTEM

PAGE
Power Steering Pump (4JJ1-TC, 4JK1-TC) .................................................................... 3B – 22 Power Steering Pump and Associated Parts............................................................ 3B – 22
Removal ....................................................................................................................... 3B – 22
Installation ................................................................................................................... 3B – 22
Power Steering Pump Disassembled View .............................................................. 3B – 23
Disassembly ................................................................................................................ 3B – 24
Inspection and Repair................................................................................................. 3B – 24
Reassembly ................................................................................................................. 3B – 25
Main Data and Specifications .................................................................................... 3B – 25
Supplemental Restraint System Steering Wheel & Column ........................................ 3B – 27 Service Precaution ...................................................................................................... 3B – 2 7
SRS Connectors .......................................................................................................... 3B – 2 7
Inflator Module ................................................................................................................ . 3B – 28
Inflator Module and Associated Parts ....................................................................... 3B – 28
Removal ....................................................................................................................... 3B – 29
Inspection and Repair (with SRS air bag) ................................................................. 3B – 31
Installation ................................................................................................................... 3B – 31
Steering Wheel................................................................................................................. 3B – 33
Steering Wheel and Associated Parts ....................................................................... 3B – 33
Removal ....................................................................................................................... 3B – 33
Installation ................................................................................................................... 3B – 36
The adjustment method in case a mark has not been applied .................................... 3B – 38
Combination Switch ........................................................................................................ 3B – 39
Combination Switch and Associated Parts .............................................................. 3B – 39
Removal ....................................................................................................................... 3B – 39
Installation ................................................................................................................... 3B – 42
Lock Cylinder .................................................................................................................. . 3B – 45
Lock Cylinder and Associated Parts ......................................................................... 3B – 45
Removal ....................................................................................................................... 3B – 45
Installation ................................................................................................................... 3B – 48
System Inspection (with SRS air bag) ....................................................................... 3B – 50

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-6 POWER-ASSISTED STEERING SYSTEM
Steering Column

RTW 53BLF000901
WARNING: TO AVOID DEPLOYMENT WHEN
TROUBLE-SHOOTING THE SRS SYSTEM, DO NOT
USE ELECTRICAL TEST EQUIPMENT, SUCH AS
A
BATTERY-POWERED OR A/C-POWERED
VOLTMETER, OHMMETER, ETC., OR ANY TYPE OF
ELECTRICAL EQUIPMENT OTHER THAN SPECIFIED
IN THIS MANUAL. DO NOT USE A NON-POWERED
PROBE-TYPE TESTER.
INSTRUCTIONS IN THIS MANUAL MUST BE
FOLLOWED CAREFULLY, OTHERWISE PERSONAL
INJURY MAY RESULT.
W hen servicing a vehicle equipped with a Supplemental
Restraint System, pay close attention to all W ARNINGS
and CAUTIONS.
For detailed explanations about SRS, refer to Restraints
section.
The steering column has three important features in
addition to the steering function:
1. The column is energy absorbing, designed to
compress in a front-end collision to minimize the
possibility of injury to the driver of the vehicle.
2. The ignition switch and lock are mounted conveniently on the column.
3. W ith the column mounted lock, the ignition and steering operation can be locked to prevent theft o
f
the vehicle.
The column can be disassembled and reassembled.
However, to insure the energy absorbing action, use
only the specified screws, bolts and nuts as designated,
and tighten them to the specified torque.
Handle the column with care when it is removed from
the vehicle. A sharp blow on the end of the steering
shaft or shift lever, or dropping the assembly could
shear or loosen the fasteners that maintain column
rigidity.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

POWER-ASSISTED STEERING SYSTEM 3B-9
4. Install all the lines and hoses. Fill the system with
new power steering fluid and bleed the system as
described in Bleeding the Power Steering System.
Operate the engine for about 15 minutes.
Remove the pump return line at the pump inlet and
plug the connection on the pump. W hile refilling the
reservoir, check the draining fluid for contamination.
If foreign matter is still evident, replace all lines,
disassemble and clean or replace the powe
r
steering system components. Do not re-use any
drained power steering fluid.

Steering Wheel Free Play Inspection
RTW 73BSH000901
1. W ith the tires in the straight-ahead position, check the amount of steering wheel play by turning the
wheel in both directions until the tires begin to move.
NOTE: The wheel free play should be checked with the
engine running. Free play: 0 - 30 mm (0 - 1.18 in)
2.
Also check the steering wheel for play and
looseness in the mount by moving it back and forth
and sideways. W hen test driving, check for hard
steering, steering shimmy and tendency to pull to
one side.

Front End Alignment Inspection and
Adjustment
Toe-in Adjustment
Toe-in: Refer to Section 3A FRONT ALIGNMENT
1. To adjust the toe-in angle, loosen the lock nuts (2) on the tie rod (1) and turn the tie rod. Turn both rods
the same amount, to keep the steering wheel
centered .
431R30006
2. Tighten the lock nut to the specified torque. Torque:
98 N ⋅
⋅⋅
⋅
m (10 kgf ⋅
⋅⋅
⋅
m/72 lb ⋅
⋅⋅
⋅
ft)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

POWER-ASSISTED STEERING SYSTEM 3B-13
Power Steering Unit Disassembled View

RTW 53BLF000401
Legend
(1) Tie-rod End
(2) Lock Nut
(3) Clip
(4) Bellows
(5) Band
(6) Tie-rod Assembly
(7) Oil Line
(8) Rack Bar
(9) Tab W asher
(10) Mounting Rubber
(11) Housing Assembly
(12) Dust Cover



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-14 POWER-ASSISTED STEERING SYSTEM
Disassembly
NOTE : The valve hosing is made of aluminum and care
should be exercised when clamping in a vise, etc.
to prevent distortion or damage.
For the left side, follow the same steps as right side.
1. Loosen lock nut and remove tie-rod end.
2. Remove clip and band, then remove bellows.
• Use a pair of pliers to open the clip. Slide the cliptoward the tie-rod end.





RUW 53BSH000401
• Remove band from the bellows by using
screwdriver.





RUW 53BSH000501


CAUTION :
For 4 ×
××
×
2 except High ride suspension models;
The band is not reusable. If removed, it must be
replaced with a new one.
Take care not to damage the bellows during band
removal.
For 4 ×
××
×
4 and 4 ×
××
×
2 High ride suspension models;
The band and bellows are not reusable. If removed,
they must be replaced with a new one.
3. Remove tie-rod assembly.
To remove, move the boot toward the tie-rod end, then remove tab washer.
4. Remove oil line, mounting rubber and dust cover.

Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found during inspection.
Check the following parts.
1. Tie-rod end
2. Lock nut
3. Clip
4. Bellows
5. Band
Tie-Rod End
If looseness or play is found when checked by moving
the end of ball joint at tie-rod end, replace tie-rod end.

Tie-Rod Assembly
If the resistance is insufficient or play is felt when
checked by moving the ball on the tie-rod, replace the
tie-rod assembly.

Rubber Parts
For 4 ×2 except High ride suspension models;
If wear or damage is found during inspection, replace
with new ones.
For 4 ×4 and 4 ×2 High ride suspension models;
Even if wear or damage is not found after removal,
replace with new ones.

Reassembly
1. Install mounting rubber and dust cover (If removed).
2. Install oil line. Torque: 12 N ⋅
⋅⋅
⋅
m (1.2 kgf ⋅
⋅⋅
⋅
m/104 lb ⋅
⋅⋅
⋅
in)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

POWER-ASSISTED STEERING SYSTEM 3B-15
3. Install tie-rod assembly with tab washer, then tighten
to specified torque. For 4 ×2 except High ride suspension models;
Torque: 83 N ⋅
⋅⋅
⋅
m (8.5 kgf ⋅
⋅⋅
⋅
m/61 lb ⋅
⋅⋅
⋅
ft)
For 4 ×4 and 4 ×2 High ride suspension models;
Torque: 108 N ⋅
⋅⋅
⋅
m (11.0 kgf ⋅
⋅⋅
⋅
m/80 lb ⋅
⋅⋅
⋅
ft)
After tightening, bend tab washer against width
across flat of inner ball joint.
4. Apply grease to the tie-rod groove. Install bellows on housing assembly.
CAUTION :
Make sure that there are no bulges or dents in the
bellows.
After installation, confirm the small end of the
bellows is inserted into the tie-rod groove.











RUW 53BSH000301

5. Caulk the band using clamp pliers 5-8840-2745-0.
For 4 ×2 except High ride suspension models;
Caulk gap(A): less than 2.0mm(0.08in).
For 4 ×4 and 4 ×2 High ride suspension models;
Caulk gap(A): 2.6 – 3.3mm(0.10 – 0.13in).

CAUTION :
Be sure to use a new band.





RUW 53BSH000601
6. Install clip.
7. Install tie-rod end and tighten lock nut.
Torque:
98 N ⋅
⋅⋅
⋅
m (10 kgf ⋅
⋅⋅
⋅
m/72 lb ⋅
⋅⋅
⋅
ft)


Main Data and Specifications
General Specifications
2W D 4W D
Power steering W ithout W ith
Type Rack and pinion
Rack stroke mm (in) 138 (5.43) 138 (5.43) 152 (5.98)
Steering unit
Lock to lock 4.84 3.38 3.23


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007