2007 Hyundai Matrix clock

2
DRIVING YOUR HYUNDAI
5STARTING
SC060A1-E Starting The Petrol Engine
C050A01E
1. Ensure that the transaxle is in neu- tral and that the clutch pedal is held depressed (manual transaxle) or the transaxle selector is at the "P" posi-tion (automatic transaxle vehicle).
2. Turn the ignition key to and hold at
the "Start" position until the enginestarts. When the engine has started, release the key. NOTE: Do not operate the starter for more than 15 seconds continuously or continue to operate the starter afterthe engine has started to avoid dam- aging the starter motor. If the engine makes a false start, allow it and thestarter motor to come to rest before attempting to start the engine again. Never attempt to start the engine withthe transaxle in gear. Do not depress the accelerator pedal whilst starting the engine. Allow theengine to idle for 20 seconds or so before driving the vehicle.
CAUTION:
Do not leave the vehicle unattended whilst idling. Never allow the vehicleto idle or warm up in a confined space (ie garage) longer than is nec- essary to move the vehicle into anopen area.
!
SC090D1-F To Remove the Ignition Key
C070C01E
1. Turn the ignition key to the "ACC" position.
2. Simultaneously push and turn the
ignition key counterclockwise from the "ACC" position to the "LOCK" position.
3. The key can be removed in the
"LOCK" position.LOCK
ACC
ON
START
fcuk-2.p65 12/27/2006, 10:14 AM
5

3 IN CASE OF EMERGENCY
6SPARE WHEELSPARE TYRE
D040A01FC-EAT TEMPORARY SPARE TYRE The following instructions for the tem- porary spare tyre should be observed:
1. Check inflation pressure as soon as possible after installing the spare tyre, and adjust to the specified pres- sure. The tyre pressure should be periodically checked and maintainedat the specified pressure whilst the tyre is stored.
Spare Tyre Pressure
Tyre Size
Inflation PressureT115/70R(D)15
420 kPa (60 psi)
2. The spare tyre should only be used temporarily and should be returned to the luggage compartment as soon as the original tyre can be repaired or replaced.
3. Continuous use at speeds of over 80 km/h (50 mph) is not recommended.
4. As the temporary spare tyre is spe- cifically designed for your car, it should not be used on any other vehicle. 5. The temporary spare tyre should not
be used on any other wheels, norshould standard tyre, snow tyre, wheel covers or trim rings be used with the temporary spare wheel. Ifsuch use is attempted, damage to these items or other car components may occur.
6. The temporary spare tyre pressure should be checked once a monthwhilst the tyre is stored.
! SD050A2-E (Not all models) The spare wheel is stored under the luggage compartment floor and is ac-cessed from within the luggage com- partment by lifting the carpet and the floor panel.To remove the spare wheel, unscrew the retainer, rotating this in an counter- clockwise direction and lift out the wheel.To replace the wheel, screw the retainer by hand until tight having located the wheel in the luggage compartment floorwell. The inflation pressure of the spare wheel should be checked at least monthly and whenever the wheel isfitted to the vehicle. Spare Tyre Pressure
Tyre Size
Inflation PressureFull Size
210 kPa (30 psi)
CAUTION:
o Do not use snow chains with your temporary spare tyre.
o Do not use more than one tempo- rary spare tyre at a time.
fcuk-3.p65 12/27/2006, 10:15 AM
6

3
IN CASE OF EMERGENCY
9
SD070F1-F 4. Put the Jack in Place
The base of the jack should be placed on firm, level ground. The jack shouldbe positioned as shown in the drawing. D060E02FC
SD070E1-E 3. Loosen Wheel Nuts
The wheel nuts should be loosened slightly before raising the car. To loosenthe nuts, turn the wheel brace counter- clockwise. Ensure that the wheel brace socket is seated properly on the nut andthat it cannot slip. Do not remove the nuts at this stage.SD070G1-E 5. Raising the Vehicle After inserting a wrench bar into the wheel nut wrench, install the wrench barinto the jack as shown in the drawing. To raise the vehicle, turn the wheel nut wrench clockwise. As the jack beginsto raise the vehicle, double check that it is properly positioned and will not slip. If the jack is on soft ground or sand, itmay be necessary to place a stout piece of timber under the base of the jack to prevent it from sinking.Raise the car high enough so that the fully inflated spare wheel can be in- stalled. HFC4022
Wrench bar
Wheel nut wrench
D060D02FC
fcuk-3.p65 12/27/2006, 10:15 AM
9

3
IN CASE OF EMERGENCY
11
SD070I1-E 7. Re-install Wheel Nuts
Fit the wheel nuts onto the studs and tighten with the wheel brace. Lower the car to the ground turning the wheel nut wrench counterclockwise. When the vehicle is firmly on the ground,remove the jack and tighten the wheel nuts securely. At the first available opportunity, the wheel nut torque shouldbe checked with a suitable torque wrench. Wheel nut tightening torque Steel wheel & aluminium alloy wheel: 90-110 Nm (65-80 lb.ft)
SD070J1-E
8. Lower Vehicle and Tighten
NutsSD070K1-E After changing wheels The pressure of the spare tyre should be checked at the first available oppor- tunity. If any doubt exists as to the tyre pressure, the vehicle should be drivenslowly to the nearest service station and the tyre pressure checked and adjusted as required. D060B01FC
D060H02FCD060I02FC
fcuk-3.p65
12/27/2006, 10:15 AM
11

6 OWNER MAINTENANCE
8
ZG030E1-A
ENGINE OIL CONSUMPTION Function of engine oil
Engine oil has the primary function of lubricating and cooling the inside of the engine.
Engine oil consumption It is normal that an engine should consume some engine oil in the course of normal driving. The cause of oil consumption in a normal engine are asfollows;
o Engine oil is used to lubricate pis- tons, piston rings and cylinders. A thin film of oil is left on the cylinder wall when a piston moves downwards in the cylinder. High negative pressure generated duringengine operation sucks some of the oil into the combustion chamber. This oil with some oil of the cylinder wall is burned by the high tempera- ture combustion gases during thecombustion process.
To add oil to the engine, remove the
filler cap by rotating in an counter-clockwise direction and pour engine oil into the engine. Before checking the level again, allow several minutes forthe oil to drain into the sump. Replace the oil filler cap rotating it in a clock- wise direction until tight.
The quantity of oil required to raise the
level from the minimum to maximumlevel is approximately 1 litre.
The distance between the "F" and "L"
marks is equal to about 1 liter(Petrol Engine)/1.2 liter(Diesel Engine) of oil.
!
CAUTION:
Slowly pour the recommended oil into a funnel. Do not overfill toprevent engine to damage.!
WARNING:
Be very careful not to touch the radiator hose when checking the engine oil as it may be hot enoughto burn you. o The engine oil consumption is
strongly effected by the viscosityand quality of oil, engine rpm and driving condition etc. More engine oil may be consumed under severe driving conditions such as high speeds, frequent accelera- tion and deceleration, compared tonormal driving.
fcuk-6.p65 12/27/2006, 10:16 AM
8

6
OWNER MAINTENANCE
9ENGINE OIL AND FILTER REPLACEMENT
SSA6040A
1.6 DOHC
Oil filler cap
Drain plug
Oil filler
G040A03E
Oil filler cap
Drain plug
Oil filler
1.8 DOHC
SG040A2-E
Petrol engine The engine oil and filter must be changed at the time or mileage inter-val specified in the maintenance sched- ule. If the vehicle is operated under severe or adverse conditions, the oiland filter must be replaced more fre- quently. To replace the oil and filter, proceed as follows:
1. Ensure that the engine is at normal operating temperature and park the vehicle on level ground with the parking brake securely applied andthe engine turned off.
2. Open the bonnet and remove the oil filler cap.
3. Prepare a suitable receptacle to collect the displaced oil and re-move the drain plug from the sump.
CAUTION:
The oil being drained from the en-gine will be hot. Care should beexercised to prevent scalding. 4. When the oil has drained from the
sump, replace the drain plug usinga new gasket ensuring that the plug is not over tightened.
5. Remove the oil filter by rotating counterclockwise, using a propri-etary oil filter removal tool if neces- sary. Note that the oil filter willcontain approximately 0.5 litres of oil and this should be collected in a suitable receptacle.
6. Install a new oil filter having smeared
the sealing ring with clean oil androtating clockwise until the filter contacts the mounting and then a further one half turn. Do not over-tighten Tightening torque: 2.3 ~ 2.5 kgf.m
7. Remove the engine oil level dip- stick.
8. Pour the specified quantity of the
recommended oil into the engine and replace the filler cap. Start the engine and ensure that no oil leaksexist. Turn off the engine and after a couple minutes, recheck the oil level.
!
fcuk-6.p65 12/27/2006, 10:16 AM
9

6
OWNER MAINTENANCE
11
!
!
4. Remove the engine oil filler cap.
5. Slide underneath the car and loosen
the oil pan drain plug by turning it counterclockwise oil pan with a wrench of the proper size. Be surethat a drain pan is in position to catch the oil as it drains out, then remove the drain plug.
WARNING:
Be very careful when draining theengine oil as it may be hot enough to burn you!
6. When the oil has stopped draining, replace the drain plug using a new gasket and retighten by turning it clockwise. Oil pan drain plug tightening torque : 3.5 ~ 4.5 kgf.m
7. Pull out the oil filter upper cap with element from the oil filter housing.Using a clean cloth, remove any dirtor oil accumulated around the oilfilter housing. 8. After mounting a new centrepipe O-
ring, new oil filter element and newO-ring to upper cap, install the up- per cap to oil filter housing and retighten by turning it clockwise. Donot over-tighten. Tightening torque : 2.5 kgf.m
CAUTION:
Do not use old oil filter upper cap O- ring and centrepipe O-ring.
!
9. Refill the crankcase with the recom- mended engine oil. Refer to the specification in chapter 9 for engine oil capacity.
CAUTION:
Slowly pour the recommended oilinto a funnel. Do not overfill to preverd engine to camage.
! 10. Start the engine and check to be
sure no oil is leaking from the drain plug or oil filter.
11. Shut off the engine and recheck
the oil level.
NOTE:
o It is recommended that the en- gine oil and filter should be changed by an Hyundai authorised repairer.
o Always dispose of used engine oil in an environmentally accept-able manner. It is suggested that it be placed in a sealed container and taken to a service station formaybe reclaimation. Do not pour the oil on the ground or put it into the household trash.
WARNING:
Used motor oil may cause irritation or cancer of the skin if left in contact with the skin for prolonged periodsof time. Wash your hands thoroughly with soap and warm water as soon as possible after handling used oil.
fcuk-6.p65 12/27/2006, 10:16 AM
11

10INDEX
2
A ACCESSORY TRAY ................................................. 1-67
AIR CONDITIONING SWITCH.................................. 1-82
AIR CONDITIONING SYSTEM MAINTENANCE ....... 6-24
AIR CLEANER ELEMENT REPLACEMENT .............6-14
ANTENNA ................................................................. 1-95
ANTI-LOCK BRAKE SYSTEM (ABS) .......................2-14
ANTI-THEFT ALARM SYSTEM .................................. 1-8
ASHTRAY ................................................................. 1-61
AUTO FUEL CUT SWITCH ....................................... 1-75
AUTOMATIC TRANSAXLE .......................................2-10
AUTOMATIC TRANSAXLE FLUID ........................... 6-19
B BATTERY MAINTENANCE .......................................6-30
BEFORE STARTING THE ENGINE ............................ 2-3
BLEEDING THE FUEL SYSTEM .............................. 6-32
BONNET RELEASE .................................................. 1-70
BRAKE PEDAL FREEPLAY .....................................6-27
BRAKE TRACTION CONTROL SYSTEM (BTCS) .... 2-14
BRAKE SYSTEM CHECKING.................................. 6-22
C
CARE OF SEAT BELTS .... .......................................1-20
CARGO AREA COVER ............................................. 1-74
CATALYTIC CONVERTOR OPERATING PRECAUTIONS ............................................................................. 7-3
CENTRE VENTILATOR ............................................. 1-76
CENTRAL DOOR LOCKS ......... .................................. 1-7
CHANGING A FLAT TYRE ......................................... 3-7
CHECKING THE CLUTCH FLU ID .............................6-23CHILD-PROOF REAR DOOR LOCK
........................... 1-7
CHILD RESTRAINT SYSTEM ................................... 1-24
CIGAR LIGHTER ....................................................... 1-60
CLUTCH PEDAL FREEPLAY ....................................6-26
COMBINATION IGNITION SWITCH ANDSTEERING LOCK ....................................................... 2-3
COOLANT TEMPERATURE GAUGE ........................1-49
DDAILY OPERATING CHECKS .................................... 6-5
DIGITAL CLOCK ....................................................... 1-59
DOOR LOCKS ............................................................. 1-5
DOOR WINDOWS ..................................................... 1-11
DRINK HOLDER ........................................................ 1-61
DRIVE BELTS ........................................................... 6-27
DRIVING FOR ECONOMY ....... .................................2-18
E EFFECTIVE BRAKING ............................................. 2-17
ELECTRIC COOLING FANS ..................................... 6-31
ELECTRONIC STABILITY PROGRAM (ESP) ...........2-16
EMERGENCY TOWING ............................................ 3-14
EMISSION CONTROL SYSTEM ................................. 7-2
ENGINE COMPARTMENT ....... ................................... 6-2
ENGINE COOLANT CHECKING AND REPLACING . 6-12
ENGINE OIL AND FILTER REPLACEMENT .............. 6-8
ENGINE OIL CONSUMPTION .................................... 6-8
ENGINE OIL REPLENISHMENT ................................. 6-7
ENGINE OIL ................................................................ 6-5 EXTERIOR REAR VIEW MIRROR ........................... 1-67
fcuk-10.p65 12/27/2006, 10:14 AM
2