2007 Hyundai Matrix alternator

5VEHICLE MAINTENANCE REQUIREMENTS
4
NO.1 2 345678 ENGINE CONTROL SYSTEM MAINTENANCE (DIESEL)
ENGINE OIL & FILTER (API Class : CH-4 or ABOVE) See Note(1)
(ACEA Class : B-4 or ABOVE)
AIR CLEANER FILTER FUEL FILTER CARTRIDGE TIMING BELTDRIVE BELT (FOR P/STR'G PUMP, ALTERNATOR & A/CON)VACUUM PUMP & VACUUM HOSEVACUUM PUMP OIL HOSE FUEL LINES, FUEL HOSE & CONNECTIONS
F030D02FC-EAT
R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary.
70 84
R I
R II I
60 72
R R R R I I I
50 60
R I I I I
40 48
R I
R
III I
30 36
R R
I I I
20 24
R I
R
III I
10 12
R I I I I
MILES X 1,000 MONTHSDESCRIPTION
Note : (1) ON A DAILY BASIS, WHENEVER THE VEHICLE IS REFUELLED OR BEFORE STARTING A LONG TRIP :"I"
fcuk-5.p65 12/27/2006, 10:15 AM
4

6
OWNER MAINTENANCE
27
SG170A1-E
Brake Pedal
The brake pedal freeplay should be checked with the engine turned off.The pedal to floor clearance should be checked with the engine running and a load of 490 N applied to the pedal. Ifeither value is incorrect, the neces- sary adjustment should be performed by a Hyundai authorised repairer. Pedalto floor clearance: 1.97 in. (50 mm)
HXGS508
0.12 ~ 0.31 in. (3 ~ 8 mm)
SG190A1-E Petrol Engine The various engine drive belts must be checked for condition, tension and free-dom from damage and excessive wear. The tension of a new belt must be checked after thirty minutes runningfollowing fitment of the new belt to allow for the initial belt stretch. CHECKING DRIVE BELTS
Water Pump Pulley
Alternator Pulley
Crankshaft Pulley 0.2~0.24 in.(5.1~6 mm)
HTB186
G180A01A-GAT
CHECKING BRAKE PEDAL CLEARANCE
45.1 mm (1.78 in.)G180A01L
You need a helper to check the brake
pedal clearance. With the engine run- ning, have your helper press down on the brake pedal several times and then hold it down with a force of about 490N(50 kg, 110 lbs). The brake pedal clearance is the distance from the top surface of the brake pedal to the as-phalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration,have it inspected by your Hyundai dealer and adjusted or repaired if nec- essary.
fcuk-6.p65 12/27/2006, 10:16 AM
27

6 OWNER MAINTENANCE
28
!
CHECKING AND REPLACING FUSES
SG200A1-E
Fusible Links
The fusible link prevents damage to
the wiring harness in the event of an electrical system malfunction. Failure of a fusiblelink is indicative of a seri- ous overload condition having occurredand therefore the electrical system should be checked by a Hyundai authorised repairer before a replace-ment link is fitted. WARNING:
Under no circumstances should a fusible link be replaced with any- thing other than a new link of thesame rating. The use of higher rated links or other means of connecting the circuit will create a potential firehazard.
Good
Bad
G200A01FC
G190B01TB-GAT Diesel Engine
At the scheduled maintenance inspec-
tion, belts should be examined for cracks, wear, fraying or other evi- dence of deterioration and replaced if necessary.
Belt routing should also be checked to
be sure there is no interference be-tween the belts and other parts of theengine.
G190B01A
Power steeringpump
A/C comp.
Auto tentioner fully
Alternator
fcuk-6.p65
12/27/2006, 10:16 AM
28