2007 HUMMER H3 brake

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 173.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 155.
Windshield Washer/Wiper. SeeWindshield
Wipers on page 157andWindshield Washer
on page 158. Cruise Controls. SeeCruise
Control on page 159.
C. Horn. SeeHorn on page 154.
D. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 175.
E. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 154.
F. All-Wheel Drive, Passenger Air Bag Status
Indicator, Locking Rear Axle, and Traction
Control System/StabiliTrak
®Buttons. See
Full-Time Four-Wheel Drive on page 111,
Passenger Airbag Status Indicator on page 179,
Locking Rear Axle on page 243,Traction
Control System (TCS) on page 241and
StabiliTrak
®System on page 244.
G. Exterior Lamps Control, Dome Override Button,
Instrument Panel Brightness Control, Fog Lamp
Button, and OnStar
®Button. SeeExterior LampsLamps on page 162,Dome Lamp Override
on page 168,Instrument Panel Brightness
on page 167,Fog Lamps on page 167, and
OnStar
®System on page 129.
H. Parking Brake Release. SeeParking Brake
on page 116.
I. Audio System. SeeAudio System(s) on
page 201.
J. Climate Control System. SeeClimate Control
System on page 170.
K. Rear Washer/Wiper Control. SeeRear Window
Wiper/Washer on page 159.
L. Off-Road Lamps Buttons. SeeOff-Road Lamps
on page 166.
M. Shift Lever. SeeAutomatic Transmission
Operation on page 106orManual Transmission
Operation on page 109.
N. Accessory Power Outlets. SeeAccessory
Power Outlet(s) on page 169.
O. Glove Box. SeeGlove Box on page 143.
153

Cruise control will not work if your parking brake is
set, or if the master cylinder brake uid level is low.
If you apply your brakes, the cruise control
shuts off.
{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could lose
control. Do not use cruise control on
slippery roads.
The cruise control disengages, if the vehicle has the
Traction Control System (TCS) and it begins to limit
wheel spin. SeeTraction Control System (TCS) on
page 241. When road conditions allow you to safely
use it again, you can turn cruise control back on.
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do not
want to. You could be startled and even
lose control. Keep the cruise control switch
off until you want to use cruise control.
1. Move the cruise control switch to on.
2. Get up to the speed desired.
3. Press in the set button at the end of the
lever and release it.
4. Take your foot off the accelerator pedal.
The cruise symbol
on the instrument
panel comes on
when the cruise
control is engaged.
160

Resuming a Set Speed
Suppose you set your cruise control at a desired
speed and then you apply the brake or step
on the clutch. This, of course, disengages the
cruise control. But you do not need to reset it.
Once you are going about 25 mph (40 km/h)
or more, you can move the cruise control switch
briey from on to resume/accelerate.
The vehicle will go back to the chosen speed and
stays there.
If you hold the switch at resume/accelerate the
vehicle will keep going faster until you release
the switch or apply the brake. Do not hold
the switch at resume/accelerate, unless you
want the vehicle to go faster.
Increasing Speed While Using
Cruise Control
There are two ways to go to a higher speed:
Use the accelerator pedal to get to the higher
speed. Press the set button at the end of
the lever, then release the button and
the accelerator pedal. You will now cruise
at the higher speed. If the accelerator pedal
is held longer than 60 seconds, cruise
control will turn off.
Move the cruise switch from on to resume/
accelerate. Hold it there until you get up
to the speed you want, and then release the
switch. To increase your speed in very
small amounts, move the switch briey to
resume/accelerate. Each time you do this, your
vehicle goes about 1 mph (1.6 km/h) faster.
Reducing Speed While Using
Cruise Control

Press and hold the set button until you reach
the desired lower speed, then release it.
To slow down in very small amounts, briey
press the set button. Each time you do this,
you will go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, your
vehicle slows down to the cruise control speed
you set earlier.
161

Using Cruise Control on Hills
How well your cruise control works on hills depends
upon your speed, load, and the steepness of the
hills. When going up steep hills, you might want
to step on the accelerator pedal to maintain the
vehicle speed. When going downhill, you might
have to brake or shift to a lower gear to keep the
vehicle speed down. Of course, applying the brake
turns off the cruise control. Many drivers nd this
to be too much trouble and do not use cruise control
on steep hills.
Ending Cruise Control
To turn off the cruise control, do one of the following:
Step lightly on the brake pedal.
Move the cruise control switch to off.
Lightly tap or press the clutch, if you have
a manual transmission.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
the cruise control set speed memory is erased.
Exterior Lamps
The control on the driver’s side of your instrument
panel operates the exterior lamps.
O(Exterior Lamps):Turn the knob, located to
the right of this symbol, to choose one of the
four exterior lamp positions.
162

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part is not working, the
other part can still work and stop you. For good
braking, though, you need both parts working well.
If the warning light comes on, there could be a
brake problem. Have your brake system inspected
right away.
This light should come on briey when you turn
the ignition key to ON. If it does not come on
then, have it xed so it will be ready to warn you
if there is a problem.When the ignition is on, the brake system
warning light will also come on when you set
your parking brake. SeeParking Brake on
page 116for more information. The light will stay
on if your parking brake does not release fully.
If it stays on after your parking brake is fully
released, it means you have a brake problem.
If the light comes on while you are driving, pull
off the road and stop carefully. You may notice that
the pedal is harder to push, or the pedal may go
closer to the oor. It may take longer to stop.
If the light is still on, have the vehicle towed for
service. SeeTowing Your Vehicle on page 294.
United StatesCanada
182

{CAUTION:
Your brake system may not be working
properly if the brake system warning
light is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
Anti-Lock Brake System
Warning Light
With the Anti-Lock Brake
System (ABS), this light
will come on briey when
you start your engine
to show it is working.
Then it will turn off.
This is normal.
If the light stays on, or comes on when you are
driving, your vehicle needs service. If the regular
brake system warning light is not on, you still
have brakes, but you do not have anti-lock brakes.
If the regular brake system warning light is also
on, you do not have anti-lock brakes and there
is a problem with your regular brakes. SeeBrake
System Warning Light on page 182.
The ABS warning light should come on briey
when you turn the ignition key to ON. If the light
does not come on then, have it xed so it will
be ready to warn you if there is a problem.
183

DIC Warnings and Messages
Messages are displayed on the DIC to notify the
driver that the status of the vehicle has changed
and that some action may be needed by the driver
to correct the condition. Multiple messages may
appear one after another. The messages are
displayed for four seconds each.
Some messages may not require immediate
action, but you should press and release the trip
odometer reset stem to acknowledge that you
received the messages and to clear them from the
display. Each message must be acknowledged
individually.
Some messages cannot be cleared from the DIC
display because they are more urgent. These
messages require action before they can be
cleared. You should take any messages that
appear on the display seriously and remember
that clearing the messages will only make
the messages disappear, not correct the problem.
The following are the possible messages that can
be displayed and some information about them.
AC (Air Conditioning) OFF
This message displays when the engine coolant
temperature is too high and the air conditioning in
your vehicle needs to be turned off. SeeEngine
Overheating on page 338andClimate Control
System on page 170for more information.
This message displays along with the ENG HOT
message.
ABS (Anti-Lock Brake System) FAULT
This message displays if there is a problem
with the Anti-Lock Brake System (ABS). Check the
ABS as soon as possible and have your vehicle
serviced by your dealer. SeeBrakes on page 347
andAnti-Lock Brake System Warning Light on
page 183for more information. Press and release
the reset stem to acknowledge the message
and clear it from the display.
196

BRAKES
This message displays if there is a problem with
the brakes. Check the brakes as soon as possible
and have your vehicle serviced by your dealer.
SeeBrakes on page 347andBrake System
Warning Light on page 182for more information.
Press and release the reset stem to acknowledge
the message and clear it from the display.
CHANGE OIL
This message displays when the oil needs to be
changed. Check the oil in your vehicle as soon
as possible and have your vehicle serviced by
your dealer. SeeEngine Oil on page 323
andScheduled Maintenance on page 429for
more information. Press and release the reset
stem to acknowledge the message and clear
it from the display.
DOORS
This message displays when one or more of
the doors is ajar. Check all the doors on your
vehicle to make sure they are closed. The
message clears from the display after all of
the doors are closed.
ENG (Engine) HOT
This message displays when the engine coolant
temperature is hot. Check the engine coolant
temperature gage. SeeEngine Coolant
Temperature Gage on page 185. Have your
vehicle serviced by your dealer as soon as
possible if you suspect the engine is overheating.
SeeEngine Overheating on page 338for more
information.
FLUID
This message displays if the brake uid is low.
Check the brake uid as soon as possible
and have your vehicle serviced by your dealer.
SeeBrakes on page 347for more information.
Press and release the reset stem to acknowledge
the message and clear it from the display.
197