2007 HUMMER H3 lights

5. After entering the switch settings, press and
release all three buttons at the same time.
The indicator lights will turn on.
6. Press and hold the button you would like to use
to control the garage door until the garage door
moves. The indicator light above the selected
button should slowly blink. You may need to
hold the button from ve to 55 seconds.
7. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
8. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or home
lighting, repeat Steps 1–8, choosing a different
function button in Step 7 than what you used for the
garage door opener.Programming Universal Home
Remote — Rolling Code
Rolling code garage door openers are used for
garage doors produced after 1996 and are
code protected. Rolling code means the coded
signal is changed every time your remote control
garage door opener is used.
Programming a rolling code garage door opener
involves time-sensitive actions, so read the
entire procedure before you begin. If you do not
follow these actions, the device will time out
and you will have to repeat the procedure.
Follow these steps to program up to three channels:
1. Press the two outside buttons at the same
time for one to two seconds, and immediately
release them.
137

Reprogramming Universal Home
Remote Buttons
You can reprogram any of the three buttons by
repeating the instructions.
Erasing Universal Home Remote
Buttons
You should erase the programmed buttons when
you sell the vehicle or terminate your lease.
To erase either rolling code or xed code on the
Universal Home Remote device, do the following:
1. Press and hold the two outside buttons at
the same time for approximately 20 seconds,
until the indicator lights, located directly
above the buttons, begin to blink rapidly.
2. Once the indicator lights begin to blink,
release both buttons. The codes from all
button will be erased.
For additional information on Universal Home
Remote, seeCustomer Assistance Offices
on page 452.
Universal Home
Remote System Operation
(With One Triangular LED)
Your vehicle may have the Universal Home
Remote System. If there is one triangular Light
Emitting Diode (LED) above the Universal
Home Remote buttons, follow the instructions
below. If your vehicle has three round LED above
the Universal Home Remote buttons, follow the
instructions under Universal Home Remote System
Operation (With three round LED).
Do not use the Universal Home Remote with any
garage door opener that does not have the stop
and reverse feature. This includes any garage door
opener model manufactured before April 1, 1982.
139

Instrument Panel Overview........................ 152
Hazard Warning Flashers.......................... 154
Other Warning Devices............................. 154
Horn.......................................................... 154
Tilt Wheel.................................................. 154
Turn Signal/Multifunction Lever.................. 155
Turn and Lane-Change Signals................. 156
Headlamp High/Low-Beam Changer.......... 157
Flash-to-Pass............................................ 157
Windshield Wipers..................................... 157
Windshield Washer.................................... 158
Rear Window Wiper/Washer...................... 159
Cruise Control........................................... 159
Exterior Lamps.......................................... 162
Headlamps on Reminder........................... 164
Daytime Running Lamps (DRL)................. 164
Automatic Headlamp System..................... 165
Off-Road Lamps........................................ 166
Fog Lamps................................................ 167
Instrument Panel Brightness...................... 167
Dome Lamp.............................................. 167
Dome Lamp Override................................ 168
Exit Lighting.............................................. 168Reading Lamps......................................... 168
Electric Power Management...................... 168
Battery Run-Down Protection..................... 169
Accessory Power Outlet(s)........................ 169
Ashtray(s) and Cigarette Lighter................ 170
Climate Controls......................................... 170
Climate Control System............................. 170
Outlet Adjustment...................................... 173
Warning Lights, Gages, and Indicators..... 174
Instrument Panel Cluster........................... 175
Speedometer and Odometer...................... 176
Trip Odometer........................................... 176
Tachometer............................................... 176
Safety Belt Reminder Light........................ 177
Passenger Safety Belt Reminder Light....... 177
Airbag Readiness Light............................. 178
Passenger Airbag Status Indicator............. 179
Battery Warning Light................................ 181
Up-Shift Light (Manual Transmission)........ 181
Brake System Warning Light..................... 182
Anti-Lock Brake System
Warning Light........................................ 183
Section 3 Instrument Panel
149

9(Off):Turn the knob to this position to turn off
all exterior lamps, including the Daytime Running
Lamps (DRL). This is a momentary control that will
spring back to AUTO when released. Vehicles
rst sold in Canada do not have the DRL disable
feature available. Vehicles rst sold in Canada
cannot turn off the DRL unless the following
conditions are met:
The vehicle has an automatic transmission.
The gear position is in PARK (P).
The headlamp switch is turned to the
Off position.
AUTO (Automatic):Turn the knob to this position
to automatically turn on the headlamps at
normal brightness, together with the following:
Sidemarker Lamps
Taillamps
Parking Lamps
Instrument Panel Lights
Due to the momentary switch design, your
automatic headlamps may be disabled even
if the control is in the AUTO position.To enable automatic lighting, do any of the
following:
Turn the headlamp control from AUTO to off
and release the control. It will return back to
the AUTO position by itself.
Turn the headlamp control from the parking
lamp position to AUTO.
Turn the headlamp control from the headlamp
position to AUTO.
To disable automatic lighting, do any of the
following:
Turn the headlamp control from AUTO to off
and release the control. It will return back to
the AUTO position by itself.
Turn the headlamp control from AUTO to the
parking lamp position.
Turn the headlamp control from AUTO to the
headlamp position.
SeeAutomatic Headlamp System on page 165
for more information.
163

Vehicles rst sold in Canada with an automatic
transmission cannot turn off automatic headlamps
unless the gear position is in PARK (P) and
the headlamp switch is turned to the Off position.
Vehicles rst sold in Canada with a manual
transmission can turn off the automatic headlamps
with the headlamp control; however, the parking
lamps will remain on.
;(Parking Lamps):Turn the knob to this
position to turn on the parking lamps, together
with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
2(Headlamps):Turn the knob to this position
to turn on the headlamps, together with the
previously listed lamps and lights.
You can switch your headlamps from low to high
beam by pushing the turn signal/multifunction
lever toward the instrument panel.
Headlamps on Reminder
A headlamp reminder chime will sound if the
following conditions are met:
The driver door is open.
Parking lamps or headlamps are manually
turned on.
The key is either not in the ignition switch, or it
is in the LOCK position of the ignition switch.
The headlamp reminder cannot be turned off if
the conditions listed above are met.
In the automatic mode, the headlamps turn off
once the ignition is in ACC.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.
164

The DRL system will come on when the following
conditions are met:
The ignition is on.
The exterior lamps control is in AUTO.
The transmission is not in PARK (P) if
you have an automatic transmission.
The light sensor determines it is daytime.
When the DRL are on, no other lamps are on.
The instrument panel will not be lit up either.
For vehicles rst sold in Canada, if parking
lamps are manually turned on, DRL will stay on.
When it begins to get dark, the automatic
headlamp system will switch from DRL to the
headlamps.
As with any vehicle, you should turn on the
regular headlamp system when you need it.
To turn off the DRL, seeExterior Lamps
on page 162.
Vehicles rst sold in Canada cannot turn
off DRL unless certain conditions are met.
SeeExterior Lamps on page 162.
Automatic Headlamp System
When it is dark enough outside, the automatic
headlamp system will turn on after the transmission
has been shifted from PARK (P) to DRIVE (D).
The headlamps, taillamps, sidemarker, parking
lamps, roof marker lamps, and the instrument panel
lights will turn on at normal brightness. The radio
lights will become more dim when the headlights
are off compared to when the headlights are on.
Your vehicle has a light sensor located on the top of
the instrument panel. Be sure it is not covered, or
the system will be on whenever the ignition is on.
The system may also turn on the headlamps when
driving through a parking garage, heavy overcast
weather, or a tunnel. This is normal.
There is a delay in the transition between the
daytime and nighttime operation of the Daytime
Running Lamps (DRL) and the automatic headlamp
system so that driving under bridges or bright
overhead street lights does not affect the system.
The DRL and automatic headlamp system will only
be affected when the light sensor detects a change
in lighting lasting longer than the delay.
165

Fog Lamps
Your vehicle has fog lamps. You can use them
for better vision in foggy or misty conditions.
Your parking lamps and/or low-beam headlamps
must be on for your fog lamps to work.
The fog lamp button
is located in the
exterior lamps control.
Press the button to turn the fog lamps on while
the headlamps or parking lamps are on. Press the
button again to turn them off. An indicator light
will glow in the button when the fog lamps are on.
Remember, fog lamps alone will not give off as
much light as your headlamps. Never use your fog
lamps in the dark without turning on the headlamps.
The fog lamps will go off whenever your
high-beam headlamps come on. When the high
beams go off, the fog lamps will come on again.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
Instrument Panel Brightness
D(Instrument Panel Brightness):This feature
controls the brightness of the instrument panel
lights.
The thumbwheel for this feature is located next to
the exterior lamp control.
Turn the thumbwheel up or down to brighten or
dim the instrument panel lights and the radio
display. The instrument panel lights, cluster, and
radio display do not dim to complete darkness.
Turn the thumbwheel all the way up to turn
the dome lamps on.
Dome Lamp
The dome and footwell lamps will come on when
you open a door. The dome lamps are located
in the cargo and front area of the vehicle.
You can also turn the dome and footwell lamps
on by turning the thumbwheel, located next to
the exterior lamps control, all the way up. In this
position, the lamps will remain on whether a
door is opened or closed.
167

Warning Lights, Gages, and
Indicators
This part describes the warning lights and gages
that may be on your vehicle. The pictures will
help you locate them.
Warning lights and gages can signal that
something is wrong before it becomes serious
enough to cause an expensive repair or
replacement. Paying attention to your warning
lights and gages could also save you or others
from injury.
Warning lights come on when there may be or is
a problem with one of your vehicle’s functions.
As you will see in the details on the next few
pages, some warning lights come on briey when
you start the engine just to let you know they
are working. If you are familiar with this section,
you should not be alarmed when this happens.Gages can indicate when there may be or is a
problem with one of your vehicle’s functions.
Often gages and warning lights work together
to let you know when there is a problem with your
vehicle.
When one of the warning lights comes on and
stays on when you are driving, or when one of
the gages shows there may be a problem, check
the section that tells you what to do about it.
Please follow this manual’s advice. Waiting to do
repairs can be costly — and even dangerous.
So please get to know your warning lights
and gages. They are a big help.
Your vehicle has a DIC that works along with the
warning lights and gages. SeeDriver Information
Center (DIC) on page 192for more information.
174