Page 358 of 570

Rocking Your Vehicle to Get It Out
First, turn the steering wheel left and right.
That will clear the area around the front wheels.
Your vehicle has a traction control system that
will activate when the system senses that
the wheels are spinning. SeeTraction Control
System (TCS) on page 309for more information.
Then, with the wheels straight ahead, shift
back and forth between REVERSE (R) and a
forward gear, spinning the wheels as little
as possible. Release the accelerator pedal while
you shift, and press lightly on the accelerator pedal
when the transmission is in gear. By slowly
spinning the wheels in the forward and reverse
directions, you will cause a rocking motion
that may free your vehicle. If that does not get
your vehicle out after a few tries, it may need to
be towed out. Or, you can use the recovery loops.
If your vehicle does need to be towed out, see
Towing Your Vehicle on page 369.
Recovery Loops
{CAUTION:
These loops, when used, are under a lot
of force. Keep people away from the
vicinity of the loops and any chains or
cables during use. Always pull the vehicle
straight out. Never pull on the loops at a
sideways angle. The loops could break off
and you or others could be injured from
the chain or cable snapping back.
Notice:Never use the recovery loops to tow
the vehicle. Your vehicle could be damaged
and it would not be covered by warranty.
358
Page 371 of 570

Selectable Extended Rear Ride
Height
If your vehicle has this feature it comes as part
of the electronically controlled air suspension
system.
The selectable rear ride height allows you to raise
the rear of the vehicle about 2 inches (5 cm)
over the normal ride height. This can be helpful
when driving off-road where you may need
more ground clearance to clear an obstacle.
The button that controls
this feature is located
on the instrument panel
to the right of the
steering wheel.To use this feature, ensure that the following
conditions are met:
The engine must be running.
All doors must be fully closed. The suspension
will not raise or lower if a door is open.
The vehicle speed must be less than 40 mph
(64 km/h). The system will not activate
otherwise.
Press the height control button to raise the rear of
the vehicle.
A light in the button will begin to ash as the rear
of the vehicle rises. Once the extended height
has been reached (this may take up to a minute),
the warning light will stop ashing and will stay
lit while the vehicle is at the extended height.
371
Page 376 of 570

Tow/Haul Mode
Tow/haul mode is used when using your vehicle to
pull a large or heavy load or trailer. Tow/haul is
also useful while pulling a load in rolling terrain, in
stop-and-go traffic, or when you need improved
low-speed control, such as when parking.
The purpose of the tow/haul mode is to do the
following:
Reduce the frequency and improve the
predictability of transmission shifts when
pulling a heavy trailer or a large or heavy load.
Provide the same solid shift feel when pulling a
heavy trailer or a large or heavy load as when
the vehicle is unloaded.
Improve control of vehicle speed while requiring
less accelerator pedal activity when pulling a
heavy trailer or a large or heavy load.
Tow/haul mode is most effective when the vehicle
and trailer combined weight is at least 75 percent of
the vehicle’s Gross Combination Weight Rating
(GCWR). See “Weight of the Trailer” later in this
section.Press the button on the
instrument panel to the
right of the steering
wheel to enable
the tow/haul mode.
A light on the instrument
panel will illuminate to
indicate that tow/haul
mode has been
selected.
Press the button again to turn off tow/haul mode.
The indicator light on the instrument panel will
turn off. The vehicle will automatically turn
off tow/haul mode every time it is started.
Driving with tow/haul mode activated without a
heavy load or with no trailer will cause reduced
fuel economy and unpleasant engine and
transmission driving characteristics, but will not
cause damage.
376
Page 383 of 570

Following Distance
Stay at least twice as far behind the vehicle ahead
as you would when driving your vehicle without
a trailer. This can help you avoid situations
that require heavy braking and sudden turns.
Passing
You’ll need more passing distance up ahead when
you’re towing a trailer. Because you’re a good
deal longer, you’ll need to go much farther beyond
the passed vehicle before you can return to
your lane.
Backing Up
Hold the bottom of the steering wheel with one
hand. Then, to move the trailer to the left,
just move that hand to the left. To move the trailer
to the right, move your hand to the right. Always
back up slowly and, if possible, have someone
guide you.
Making Turns
Notice:Making very sharp turns while
trailering could cause the trailer to come in
contact with the vehicle. Your vehicle could be
damaged. Avoid making very sharp turns
while trailering.
When you’re turning with a trailer, make wider
turns than normal. Do this so your trailer
won’t strike soft shoulders, curbs, road signs,
trees or other objects. Avoid jerky or sudden
maneuvers. Signal well in advance.
Turn Signals When Towing a Trailer
The arrows on your instrument panel will
ash whenever you signal a turn or lane change.
Properly hooked up, the trailer lamps will also
ash, telling other drivers you’re about to
turn, change lanes or stop.
When towing a trailer, the arrows on your
instrument panel will ash for turns even if the
bulbs on the trailer are burned out. Thus, you may
think drivers behind you are seeing your signal
when they are not. It’s important to check
occasionally to be sure the trailer bulbs are still
working.
383
Page 389 of 570