2007 HUMMER H2 CD player

A-B:This button is used to repeat predened
sections. Press this button once while the disc is
playing to select the starting position. Press a
second time to select the end position. Press a
third time to turn the function off.
GO:Press this button to access scenes directly
by entering the time/title/chapter.
SUBTITLE:Press this button to switch between
the default language set on the DVD player and up
to any alternate language that could be recorded
on the DVD disc itself. Press this button again
to turn the subtitle function off.
PBC (Playback Control):Press this button to
turn video CD playback control on or off.
ZOOM:Press this button to zoom in on video
images during play or pause modes. Press
and release this button multiple times to increase
the image size in sequence, at 1, 2, or 3 times
of normal size, or ZOOM OFF.
In zoom modes, the direction arrow buttons can be
used to change the zoomed monitor viewing area.RETURNq:Press this button to go back
one step in the RSE On-Screen Display (OSD)
menu and some DVD menus. Press this button
to exit the current menu and to go to the
previous menu.
MUTE
$:Press this button to mute the audio
sound output.
DISP. (Display):Press this button to switch
between display functions of elapsed/remaining
time, full information, or off.
REPEAT
k:Press this button to switch between
repeat functions of title, chapter, track, entire
disc, or off.
AUDIO:Press this button to switch between the
default language set on the DVD player or to
any alternate language that could be recorded on
the DVD disc itself.
Numeric Keys:The numbered buttons located on
the lower left side of the system’s remote control
are numerical digits assigned to menu options.
To use the numeric buttons, follow the menu
instructions by pressing the number that has been
assigned to the preferred option.
283

Battery Replacement
To change the remote control batteries, do the
following:
1. Slide the battery door, located on the back of
the remote control, down.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly, using the diagram on the inside
of the battery compartment.
3. Close the battery door.
If the remote control is to be stored for a long
period of time, remove the batteries and keep them
in a cool, dry place.
Using the RSE On-Screen
Display (OSD) Menu
To use the RSE OSD menu while using the DVD
player or an auxiliary device, do the following:
1. Press the SETUP button on the system’s
remote control to access the general setup
menu, see “Remote Control” earlier in
this section.
2. Once this menu is on the screen, press the
directional arrows and then the ENTER
button to navigate the screen.
This menu lets you select default preferences
for language, video, audio, and ratings.
Not all DVDs support all of the feature defaults
in the setup menus. If a feature is not
supported, the defaults are provided by the
DVD media.
The default language selection applies to all
future DVDs.
3. Press the RETURN button on the system’s
remote control to exit this menu, or wait for
the menu to time out.
284

Displaying JPEG Images
To use the RSE OSD menu for displaying
JPEG images, do the following:
1. Insert a CD with JPEG images and then
select it for playback from the RSE
on-screen display menu.
A slide show of the images, starting from the
rst picture, automatically begins, or press
PLAY on the system’s remote control to start.
The images change automatically every
10 seconds.
2. Press the directional arrows to see the next or
previous pictures.
3. You can also press the numeric digits on the
system’s remote control to enter the picture
number and then ENTER, to access the
images directly.4. Press MENU on the system’s remote control
to display nine images at one time.
5. Press the directional arrows on the system’s
remote control to select an image to enlarge
and then press ENTER.
If both MP3 and JPEG les are recorded on a
disc, the player offers a choice of which to
play rst. If no choice is made within 10 seconds,
the MP3 les play automatically. The previous
menu can be accessed at any time by pressing
TITLE on the system’s remote control.
Displaying Disc and Video CD Disc Status
To display a disc status, press DISP (display)
on the system’s remote control to show the total
elapsed time and current chapter elapsed time.
To display a video CD disc status, press DISP on
the system’s remote control to show the total
elapsed time and current track elapsed time.
286

Displaying DVD Player Default Settings
To display the DVD player default settings, do the
following:
1. Press the SETUP button on the system’s
remote control to display Language, Video,
Audio, and Rating in the default setup menu.
2. Press the left and right directional arrows
on the system’s remote control to select
any one of the options on the default setup
menu and then press ENTER.
3. Press the up and down directional arrows on
the system’s remote control to select one of the
preference choices and then press ENTER.
Language:The on-screen display (OSD)
language, subtitle language, audio language, and
DVD menu language can be set according to
personal preference. The OSD can also be
switched on or off. The factory default language
set is English.For the language setup, select one of ve choices
from the display:OSD Menu
Subtitle
Audio
DVD Menu
Default
Video:Picture shape and video format can be set
according to personal preferences. The TV
shape can be set to t different types of monitors,
4:3 Letterbox, 4:3 Pan-Scan, 16:9 Wide Screen.
The factory default TV shape is 4:3 Letterbox.
The video format, used by the DVD player can be
set to NTSC, PAL, or Auto. The NTSC is a
standard format for North America and there is no
need to change this setting. The factory default
video setting is Auto.
287

Problem Recommended Action
Distorted/Interference
DVD audio sound from
vehicle radio.
Make sure the FM
Modulator and vehicle
radio are tuned to the
same FM frequency.
Change FM
frequency on the
vehicle radio and FM
Modulator to an
unused frequency in
the current driving
area. (No local,
strong FM station on
the frequency
selected.)
DVD Messages
The following errors display on the video monitor.
Bad Disc:This message displays if a disc
with an unsupported format is inserted into the
DVD player, or if the disc is unreadable.
Region Error:This message displays if the
region code of the DVD is not compatible with the
region code of the DVD player.No Disc:This message displays when you try to
play or eject a disc that is not in the player.
X:A white X displays, in the upper left corner of
the video monitor, if the operation that has
been selected is not currently available.
DVD Distortion
You could experience video distortion while
operating cellular phones, scanners, CB radios,
Global Position Systems (GPS)*, two-way
radios, mobile fax, or walkie talkies.
It might be necessary to turn off the DVD player
while operating one of these devices in or near the
vehicle.
*Excludes the OnStar
®System.
Cleaning the Video Screens
The video display screens are made of a specially
coated glass and can be scratched or damaged
by abrasive products, solvents, or ammonia-based
window cleaners. Occasionally take a soft,
lint-free, cotton cloth that has been slightly
dampened with warm water and wrung out
completely. Dry the screens by wiping with a clean
dry cotton cloth.
293

Cleaning the Components
Use care when directly touching or cleaning the
components such as the DVD player and the discs
that are used for your viewing entertainment, as
damage may result. SeeCare of the CD and
DVD Player on page 300andCare of Your CDs
and DVDs on page 299in this manual for
more information.
Rear Seat Audio (RSA)
This feature allows rear seat passengers to listen
to any of the sources: radio, cassette tapes, or
CDs. However, the rear seat passengers can only
control the sources that the front seat passengers
are not listening to. For example, rear seat
passengers may listen to and control cassette
tapes or CDs through the headphones while the
driver listens to the radio through the front
speakers. The rear seat passengers have control
of the volume for each set of headphones.
The front seat audio controls always have priority
over the RSA controls. If the front seat
passengers switch the source for the main radio to
a remote source, the RSA will not be able to
control the source. You can operate the rear seat
audio when the main radio is off.
P(Power):Press this button to turn the system
on or off. The rear speakers will be muted
when the power is turned on unless your vehicle
is equipped with the Bose
®audio system.
u(Volume):Turn this knob to increase or to
decrease the volume. The left knob controls
the left headphones and the right knob controls
the right headphones.
SRC (Source):Press this button to select a
source: radio, cassette tape, or CD.
294

Radio Reception
You may experience frequency interference and
static during normal radio reception if items
such as cellphone chargers, vehicle convenience
accessories, and external electronic devices
are plugged into the accessory power outlet. If
there is interference or static, unplug the item from
the accessory power outlet.
AM
The range for most AM stations is greater than for
FM, especially at night. The longer range can cause
station frequencies to interfere with each other.
For better radio reception, most AM radio stations
boosts the power levels during the day, and then
reduce these levels during the night. Static can also
occur when things like storms and power lines
interfere with radio reception. When this happens,
try reducing the treble on your radio.
FM Stereo
FM stereo gives the best sound, but FM signals
reach only about 10 to 40 miles (16 to 65 km). Tall
buildings or hills can interfere with FM signals,
causing the sound to fade in and out.
XM™ Satellite Radio Service
XM™ Satellite Radio Service gives digital radio
reception from coast-to-coast in the 48 contiguous
United States, and in Canada. Just as with FM,
tall buildings or hills can interfere with satellite
radio signals, causing the sound to fade in and out.
In addition, traveling or standing under heavy
foliage, bridges, garages, or tunnels can cause
loss of the XM™ signal for a period of time.
The radio could display NO SIGNAL to indicate
interference.
Care of the Cassette Tape Player
A tape player that is not cleaned regularly
can cause reduced sound quality, ruined
cassettes, or a damaged mechanism. Cassette
tapes should be stored in their cases away
from contaminants, direct sunlight, and extreme
heat. If they are not, they may not operate properly
or may cause failure of the tape player.
297

The tape player should be cleaned regularly after
every 50 hours of use. The radio may display
CLEAN to indicate that the tape player has been
used for 50 hours without resetting the tape
clean timer. If this message appears on the
display, the cassette tape player needs to be
cleaned. It will still play tapes, but it should
be cleaned as soon as possible to prevent damage
to the tapes and player. If there is a reduction in
sound quality, try a known good cassette to
see if the tape or the tape player is at fault. If this
other cassette has no improvement in sound
quality, clean the tape player.
For best results, use a scrubbing action,
non-abrasive cleaning cassette with pads which
scrub the tape head as the hubs of the cleaner
cassette turn. The recommended cleaning cassette
is available through your dealer.When cleaning the cassette tape player with the
recommended non-abrasive cleaning cassette, it is
possible that the cassette may eject, because
the cut tape detection feature on the radio
may recognize it as a broken tape, in error. To
prevent the cleaning cassette from being ejected,
use the following steps:
1. Turn the ignition on.
2. Turn the radio off.
3. Press and hold the TAPE DISC button for
ve seconds. READY will appear on the
display and the cassette symbol will ash for
ve seconds.
4. Insert the scrubbing action cleaning cassette.
5. Eject the cleaning cassette after the
manufacturer’s recommended cleaning time.
When the cleaning cassette has been
ejected, the cut tape detection feature
will be active again.
298