2007 HUMMER H2 clock

Daytime Running Lamps (DRL)
To replace a daytime running lamp bulb, do the
following:
1. Locate the lamp
assembly behind the
front bumper. It is
easiest to come
in from the side of
the vehicle
through the wheel
opening.
2. Turn the bulb socket counterclockwise and
remove it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Install the new bulb into the bulb socket.
5. Reinstall the bulb socket into the lamp housing
and turn it clockwise until it locks.
Roof Marker Lamps
Corner Roof Marker Lamps
To replace one of these bulbs, do the following:
1. Remove the screw and lift off the lens.
2. Turn the bulb socket counterclockwise to
remove it.
3. Remove the bulb.
4. Install a new bulb into the socket.
5. Reinstall the socket into the lens and turn it
clockwise to lock it into place.
6. Hook the side of the lens with the hook end into
the notch rst and then tighten the screw.
443

Center Roof Marker Lamps
To replace one of these bulbs, do the following:
1. Push in on the notch with a at tool and pull
the lamp out.
2. Turn the bulb socket counterclockwise and
remove it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Install a new bulb into the bulb socket.
5. Place the hook end of the lamp in place on
one side and push the other end of the lamp
down until it locks in place.
Taillamps, Turn Signal, Stoplamps
and Back-up Lamps
A. Stoplamp/Taillamp
B. Turn Signal Lamp
C. Back-Up Lamp
To replace one of these bulbs, do the following:
1. Open the liftgate or tailgate. SeeLiftgate
(SUV) on page 104orTailgate/Spare Tire
Carrier on page 108for more information.
444

2. If your vehicle is equipped with a taillamp
guard, you will need to remove it in order
to access the taillamp. To do this, remove the
four screws retaining the taillamp guard
making sure not to remove the plastic
retainers.
3. Remove the
two screws from
the rear lamp
assembly and
remove the rear
lamp assembly.
4. Turn the bulb socket counterclockwise to
remove it from the taillamp housing.5. Pull the bulb straight out from the socket.
6. Press a new bulb into the socket, insert it into
the taillamp housing and turn the socket
counterclockwise until it is locked in place.
7. Reinstall the rear lamp assembly and tighten
the screws.
8. Reinstall the taillamp guard by lining up the
guard with the holes in vehicle. Then install
and tighten the four screws.
445

Your vehicle may have a taillamp in the bumper.
To replace it, do the following:
1. Locate the affected
taillamp which is
behind and
under the bumper.
2. Turn the bulb socket counterclockwise and
remove it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Install the new bulb into the bulb socket.
5. Reinstall the bulb socket into the lamp housing
and turn it clockwise to lock it.Replacement Bulbs
Exterior Lamp Bulb Number
Back-up Lamp 3156K
Daytime Running Lamp (DRL) 4114K LCP
Front Turn Signal and
Parking Lamp4157K or 3157KX
Low-Beam and High-Beam
Headlamps9007
Rear Taillamp and Stoplamp 3057K
Rear Taillamp in Bumper 3057K
Rear Turn Signal Lamp 3156K
Roof Marker Lamp Center 168
Roof Marker Lamp Corner 194
For replacement bulbs not listed here, contact
your dealer.
446

Removing the Jack (SUV)
The jack is stored behind the driver’s side second
row seat.
1. Fold the driver’s side second row seat down
to access the jack. See60/40 Split Bench
Seat on page 15for more information.
2. Insert the wheel wrench (A) into the hole (B)
and turn it counterclockwise to release it.
3. Grasp and lift the jack out of the bracket.
Removing the Spare Tire (SUV)
The spare tire is attached to the tire carrier.
To remove the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 108for tire carrier operation.
2. Unscrew the wing nut on the back of the tire
carrier.
472

3. Pull off the license plate holder from the
spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts. Turn the
wheel wrench with the wheel wrench
extender counterclockwise to loosen the
wheel nuts.5. Remove the three wheel nuts holding the
spare tire onto the tire carrier.
6. Pull off the spare tire and gently lower it to the
ground. Set it next to the at tire.
473

Release the jack by inserting the wheel wrench (A)
into the hole (B) and turn counterclockwise.
Before proceeding, be sure to set the wheel blocks
at the appropriate tires as previously shown.
Remove the wheel
blocks from the tool
bag. Then lift the wheel
block as shown to
lock it into place.
Removing the Spare Tire (SUT)
The spare tire is attached to the tire carrier.
To remove the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 108for tire carrier operation.
2. Unscrew the wing nut on the back of the
tire carrier.
476

3. Pull off the license plate holder from the
spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.
5. Turn the wheel wrench with the wheel wrench
extender counterclockwise to loosen the
wheel nuts.6. Remove the three wheel nuts holding the
spare tire onto the tire carrier.
7. Pull off the spare tire and gently lower to the
ground. Set it next to the at tire.
477