2007 HONDA FIT bulb

This indicator monitors the
temperature of the engine coolant. It
normallycomesonwhenyouturn
the ignition switch to the ON (II)
position and goes off after a few
seconds. In normal driving
conditions, this indicator should not
blink or stay on. In severe driving
conditions, such as very hot weather
or a long period of uphill driving, this
indicator may blink. This means the
engine coolant temperature is high.
If the indicator begins to blink while
you are driving, be sure to slow down
to prevent overheating. If the
indicator stays on, pull safely to the
side of the road and turn off the
engine. See page for instructions
and precautions on checking the
engine’s cooling system. This
indicator monitors the
temperature of the engine coolant. If
th ere is no problem, this indicator
comes on when the engine is cold. If
it comes on when the engine is warm
(normal operating temperature),
have the vehicle inspected by your
dealer as soon as possible.
Do not drive the vehicle while the
indicator is on or the engine may be
damaged. The
left or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash. 188
216
Instrument Panel Indicators
High T emperature
Indicator Low Temperature
Indicator Turn Signal and
Hazard Warning
Indicators
Inst rument s and Cont rols
63

Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn off the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, then pull the inner
f ender cover back.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area, readjustment may be
required. Adjustments should be
done by your dealer or other
qualif ied mechanic.
1.
2.
Headlight A iming Replacing a Headlight Bulb
Lights
186
HOLDING CLIP
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.Make sure that the hold-down
wire is installed properly and
securely. You can check its
installation f rom the inspection
window on the headlight assembly. Install the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.Install the rubber seal over the
back of the headlight assembly.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely. Turn on the
headlights to test the new bulb.
Reinstall the inner f ender cover.
Then reinstall the holding clip, and
lock it in place by pushing on its
center.
Unclip the end of the hold-down
wire f rom its slot. Pivot the wire
out of the way, then remove the
bulb.
5. 6.
3.
4. 7.8.
9.
10.
Lights
Maint enance
187
RUBBER WEATHER SEAL
HOLD-DOWN
WIRE BULB
ELECTRICAL
CONNECTOR
HOLD-DOWN
WIRE
INSPECTION WINDOW

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, then pull the inner
f ender cover back.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms. Remove the socket by turning it
one-quarter turn counterclockwise. Reinstall the inner f ender cover.
Then reinstall the holding clip, and
lock it in place by pushing on its
center. Turn on the lights to make sure
the new bulb is working.
1. 2.
3.
4.5.
6.
7.
Lights
Replacing a Parking L ight/Front
Side Marker Bulb and a Turn
Signal Light Bulb
188
HOLDING CLIP
PARKING LIGHT/FRONT SIDE MARKER
BULB TURN SIGNAL LIGHT BULB

The fog lights use halogen bulbs.
Wh en replacing a bulb, handle it
carefully. See page for more
inf ormation.
To remove the f og light assembly,
slide it inward, then caref ully pull
it out of the bumper. Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the f og light assembly,
then tighten the screw.
Use a Phillips-head screwdriver to
remove the screw. Remove the bulb by turning it
about one-quarter turn
counterclockwise.
1.
2. 3.
4.5.
6.
7.
8.
186
On Sport model
Lights
ReplacingaFogLightBulb
Maint enance
189
ELECTRICAL CONNECTOR
SCREW

Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.Determine which of the f our bulbs
is burned out: stop/taillight, back-
up light, turn signal light, or
taillight.
Remove the socket by turning it
one-quarter turn counterclockwise.Remove the burned out bulb f rom
the socket by pulling it straight out
of its socket.
Install the new bulb in the socket.
Turn on the lights to make sure
the new bulb is working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Reinstall the light assembly cover.
1. 2.
3.4.
5.
6.
7.
8.
Lights
Replacing Rear Bulbs
190
LIGHT ASSEMBLY COVER

Open the tailgate. Remove the
light assembly cover by pushing in
the tabs on both sides and pulling
the cover of f .
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Press the brake pedal to make
sure the new bulb is working. Put the cover back on the light
assembly. Push it in until it locks
in place.
1.
2. 3.
4.5.
6.
Lights
Replacing a High-mount Brake
Light Bulb
Maint enance
191

CONT INUED
....................................
Accessories . 138
ACCESSORY (Ignition Key .......................................
Position) .77
...............
Accessory Power Socket . 98
....................
Additives, Engine Oil . 177
.......
Adjusting the Steering Wheel . 74
...........................
Advanced Airbags .27
...............................
Airbag (SRS) . 9, 22
..............
Air Conditioning System . 100
.........................................
Usage .101
.......................
Air Pressure, Tires .198
.......................
Alcohol in Gasoline .132
......................................
Antif reeze .180
Anti-lock Brakes (ABS) ...............................
Indicator . 62, 162
...................................
Operation .162
..............
Anti-thef t, Audio System . 124
.
Anti-thef t Steering Column Lock . 77
................................
Audio System .105
...
Automatic Seat Belt Tensioners . 20
.............
Automatic Speed Control . 127
..............
Automatic Transmission . 151
..........................
Capacity, Fluid .232
...............
Checking Fluid Level . 183..........................
Paddle Shif ters .156
.......................................
Shif ting .151
Shif t Lever Position ...............................
Indicators .151
................
Shif t Lever Positions . 152
....................
Shif t Lock Release . 155
............................
Capacities Chart .232
.............
Carbon Monoxide Hazard . 53
..............................................
Cargo .140
Battery
Charging System ...........................
Indicator . 60, 218
............................
Jump Starting .214
..............................
Maintenance .203
............................
Specif ications .233
..............................
Bef ore Driving .131
....................................
Belts,Seat .8 , 18
...........................
Beverage Holders . 97
..................................
Booster Seats . 50
Brakes ...........
Anti-lock System (ABS) . 162
.............
Break-in, New Linings . 132
....................
Bulb Replacement .190
...........................................
Fluid .185
.........................................
Parking . 95
.................
System Indicator . 60, 220 ..........................
System Design .161
........................
Wear Indicators .161
.............................
Braking System .161
.................
Break-in, New Vehicle . 132
..
Brightness Control, Instruments . 73
..................
Brights, Headlights . 71,72
Bulb Replacement ..........................
Back-up Lights .190
..............................
Brake Lights .190
Front Parking Lights/ ...
Front Side Marker Lights . 188
.................................
Fog Lights .189
.................................
Headlights .186
.........
High-mount Brake Light . 191
............................
Specif ications .233
....................................
Taillights .190
.............
Turn Signal Lights . 188,190
..............................
Bulbs, Halogen .186
Index
A
B
C
INDEX
I