2007 HONDA FIT lights

This section explains why it is
important to keep your vehicle well
maintained and how to follow basic
maintenance safety precautions.
If you have the skills and tools to
perform more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer. This section also includes
instructions on how to read the
maintenance minder messages on
the information display, a
maintenance record, and instructions
for simple maintenance tasks you
may want to take care of yourself. ......................
Maintenance Saf ety .166
....................
Maintenance Minder .167
....................
Maintenance Record .174
..............................
Fluid Locations .176
........................
Adding Engine Oil .177
Changing the Engine Oil
....................................
and Filter .178
..............................
Engine Coolant .180
....................
Windshield Washers .182
.......................
Transmission Fluid .183
..........
Automatic Transmission .183
..............
Manual Transmission .184
................
Brake and Clutch Fluid .185
.............................................
Lights .186
................
Cleaning the Seat Belts .192
.....................................
Floor Mats .192
..............................
Audio Antenna .193
..................
Dust and Pollen Filter .194
.................................
Wiper Blades .194
...........................................
Wheels .197
...............................................
Tires .197
...................
Checking the Battery .203
.............................
Vehicle Storage .204
245
Maintenance
Maint enance
165

µµµ
µ
µ
µ
Ì Engine
oil level Check every
time you fill the fuel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
you fill the fuel tank. See page .
Automatic transmission Check
the fluid level monthly. See page
.
Brakes Check the fluid level
monthly. See page .
Tires Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page
.
Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
and licen se plate lights monthly.
See page .
Youshouldcheckthefollowing
items
at the specified interval s. If
you are unsure of how to perf orm
any check, turn to the appropriate
page listed. U.S. Vehicles:
According to state and federal
regulations, f ailure to perf orm
maintenance on the items marked
with will not void your emissions
warranties. However, all
maintenance services should be
perf ormed in accordance with the
intervals indicated by the
inf ormation display.
However, service at a dealer is not
mandatory to keep your warranties
in effect. Maintenance may be done
by any qualif ied service f acility or
person who is skilled in this type of
automotive service. Make sure to
have the service f acility or person
reset the display as previously
described. Keep all receipts as proof
of completion, and have the person
who does the work fill out the
maintenance record. Check your
warranty booklet f or more
inf ormation.
We recommend using Honda parts
and fluids whenever you have
maintenance done. These are
manuf actured to the same high-
quality standards as the original
components, so you can be conf ident
of their perf ormance and durability. 135
136
183 185
199
186
Maintenance Minder
Owner’s Maintenance Checks Maintenance,
replacement, or repair of
emissions control devices and
systems may be done by any
automotive repair establishment
or individual using parts that are
‘‘certif ied’’ to EPA standards.
172

Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn off the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, then pull the inner
f ender cover back.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area, readjustment may be
required. Adjustments should be
done by your dealer or other
qualif ied mechanic.
1.
2.
Headlight A iming Replacing a Headlight Bulb
Lights
186
HOLDING CLIP
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.Make sure that the hold-down
wire is installed properly and
securely. You can check its
installation f rom the inspection
window on the headlight assembly. Install the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.Install the rubber seal over the
back of the headlight assembly.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely. Turn on the
headlights to test the new bulb.
Reinstall the inner f ender cover.
Then reinstall the holding clip, and
lock it in place by pushing on its
center.
Unclip the end of the hold-down
wire f rom its slot. Pivot the wire
out of the way, then remove the
bulb.
5. 6.
3.
4. 7.8.
9.
10.
Lights
Maint enance
187
RUBBER WEATHER SEAL
HOLD-DOWN
WIRE BULB
ELECTRICAL
CONNECTOR
HOLD-DOWN
WIRE
INSPECTION WINDOW

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, then pull the inner
f ender cover back.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms. Remove the socket by turning it
one-quarter turn counterclockwise. Reinstall the inner f ender cover.
Then reinstall the holding clip, and
lock it in place by pushing on its
center. Turn on the lights to make sure
the new bulb is working.
1. 2.
3.
4.5.
6.
7.
Lights
Replacing a Parking L ight/Front
Side Marker Bulb and a Turn
Signal Light Bulb
188
HOLDING CLIP
PARKING LIGHT/FRONT SIDE MARKER
BULB TURN SIGNAL LIGHT BULB

The fog lights use halogen bulbs.
Wh en replacing a bulb, handle it
carefully. See page for more
inf ormation.
To remove the f og light assembly,
slide it inward, then caref ully pull
it out of the bumper. Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the f og light assembly,
then tighten the screw.
Use a Phillips-head screwdriver to
remove the screw. Remove the bulb by turning it
about one-quarter turn
counterclockwise.
1.
2. 3.
4.5.
6.
7.
8.
186
On Sport model
Lights
ReplacingaFogLightBulb
Maint enance
189
ELECTRICAL CONNECTOR
SCREW

Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.Determine which of the f our bulbs
is burned out: stop/taillight, back-
up light, turn signal light, or
taillight.
Remove the socket by turning it
one-quarter turn counterclockwise.Remove the burned out bulb f rom
the socket by pulling it straight out
of its socket.
Install the new bulb in the socket.
Turn on the lights to make sure
the new bulb is working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Reinstall the light assembly cover.
1. 2.
3.4.
5.
6.
7.
8.
Lights
Replacing Rear Bulbs
190
LIGHT ASSEMBLY COVER

Open the tailgate. Remove the
light assembly cover by pushing in
the tabs on both sides and pulling
the cover of f .
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Press the brake pedal to make
sure the new bulb is working. Put the cover back on the light
assembly. Push it in until it locks
in place.
1.
2. 3.
4.5.
6.
Lights
Replacing a High-mount Brake
Light Bulb
Maint enance
191