2007 HONDA ELEMENT high beam

ÎThe U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.
Instrument Panel
Instru me ntsand Cont ro ls
59
CRUISE CONTROL
INDICATOR
(P.61)
(P.64)
VEHICLE STABILITY
ASSIST(VSA) SYSTEM
INDICATOR (P.61)
(P.65)
MAINTENANCE
MINDER
INDICATOR (P.61)
LIGHT ON INDICATOR
SEAT BELT REMINDER
INDICATOR (P.60)
(P.62)
PARKING
BRAKE AND
BRAKE SYSTEM
INDICATOR
CHARGING SYSTEM INDICATOR
LOW FUEL
INDICATOR
IMMOBILIZER SYSTEM
INDICATOR (P.62) SUPPLEMENTAL
RESTRAINT
SYSTEM INDICATOR
SIDE
AIRBAG OFF
INDICATOR
LOW
TIRE PRESSURE
INDICATOR (P.64)
VSA ACTIVATION
INDICATOR
(P.64)
(P.60,
232)
(P.63)
(P.63)
(P.60,
233)
(P.60) HIGH BEAM INDICATOR
(P.63) MALFUNCTION INDICATOR
LAMP
LOW OIL PRESSURE
INDICATOR
ANTI-LOCK BRAKE SYSTEM
INDICATOR DOOR
AND TAILGATE
OPEN MONITOR (P.63)
(P.61) TPMS
INDICATOR
(P.60, 231)

This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. If you turn the
ignition switch to the ACCESSORY
(I) or LOCK (0) position without
turning off the light switch, this
indicator will stay on. A reminder
chime will also sound when you open
the driver’s door.
This indicator comes on with the
high beam headlights. For more
info rmation, see page .
On Canadian models, this indicator
comes on with reduced brightness
wh en the daytime running lights
(DRL) are on (see page ). This
indicator comes on when the
washer fluid level is low. Add washer
fluid when you see this indicator
come on (see page ).
All of the indicators in the monitor
display come on f or a f ew seconds
when you turn the ignition switch to
the ON (II) position. The appropriate indicator comes on
in this display if the tailgate or any
door is not closed tightly. When the indicator comes on, there
is about 2.8 U.S. gal (10.5
)of fuel
remaining in the tank bef ore the
needle reaches E. There is a small
reserve of f uel remaining in the tank
when the needle does reach E.
This indicator comes on as a
reminder that you must ref uel soon.
72
72 193
Canadian models only
Instrument Panel Indicators
Lights On Indicator
High Beam Indicator
Washer Level Indicator
Door and T ailgate Open Monitor
Low Fuel Indicator
Inst rument s and Cont rols
63
LOW FUEL INDICATOR

µµPush down on the
lever to signal a lef t turn and up to
signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
Turn Signal
OFF
Parking and interior lights
Headlights on
High Beams
Flashhighbeams Turning the switch to
the ‘‘ ’’ position turns on the
parking lights, taillights, instrument
panel lights, side-marker lights, and
rear license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or ‘‘ ’’ position, the
lights on indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position.
If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
1.
2.
3.
4.
5.
6.
CONT INUED
Turn Signal
Headlights
Turn Signal and Headlights
Inst rument s and Cont rols
71

µ Push the lever back
until youhearaclicktoturnonthe
high beams. The blue high beam
indicator will come on (see page ).
Pull the lever back again to low
beams. With the headlight switch of f or in
the position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
You can change the instrument panel
brightness only when the light
switch is on.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
To adjust the brightness, turn the
knob on the instrument panel.
63
Canadian models only
High Beams
Daytime Running L ights Instrument Panel Brightness
Turn Signal and Headlights, Instrument Panel Brightness
72

Reinstall the rubber weather seal.
Make sure it is right side up; it is
marked ‘‘TOP.’’ Install the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely. Turn on the
headlights to test the new bulb.
(Driver’s side)
Install the f ront end of the air
intake duct.
Remove the rubber weather seal
by pulling on the tab. Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Unclip the end of the hold-down
wire f rom its slot. Pivot the wire
out of the way, then remove the
bulb. The high beam headlight bulb and
the low beam headlight bulb are
replaced the same way.
Open the hood.
If you need to change the
headlight bulb on the driver’s side,
remove the f ront end of the air
intake duct by pulling it out.
1.
2.
3.
4. 5.
6.
7.
8.
CONT INUED
On SC model
Lights
Maint enance
199
AIR INTAKE DUCT

µ
µ µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
ÎÎ
ÎÎ
Î
Î
Î
Î
Î Î
Î
Î
Î
Î
Î
Î
Î
Î
Specifications
T
echnical Inf ormat ion
245
Air Conditioning Fuses
Battery Lights Tires Alignment
HFC-134a
(R-134a)
12 V 60/55 W (H4/HB2)
0°13’
0.08
in (2.0 mm)
0.0in(0mm)
Refrigerant
type
Charge quantity
Lubricant type Interior
Under-hood
Capacity 12 V 45 AH/20 HR
Headlights
Headlights
High Beam
Headlights Low Beam
Front turn signal/parking
lights
Front side marker lights
Rear turn signal lights
Brake/Taillights
Back-up lights
License plate lights
Ceiling light
Spotlights
Cargo area light
High-mount brake light 12 V
12
V
12
V
12
V
12
V
12
V
12
V
12
V
12
V
21 W
10
W
8W 10
W
3CP
18
W (21 CP)
21/5
W
21
W
3CP 21/5
W
12
V 60 W
12 V 55 W
12 V
12 V 5 W
P215/70R16 99S
0°24’ 1°00’
Size
Pr essure
60 psi (420 kPa , 4.2 kgf/cm
)
35
psi (240 kPa , 2.4 kgf/cm
)
33
psi (230 kPa , 2.3 kgf/cm
)
P225/55R18
97H
32 psi (220 kPa , 2.2 kgf/cm)
32 psi (220 kPa , 2.2 kgf/cm
)
28/8 W
See page237or the fuse label
attached to the inside of the fuse
box door under the steering
column.
See page238or the fuse box
cover.
1°50’
Toe-in
Camber
Caster
1°06’
Front/Rear
Front
Rear
Spare
All models except SC
SC model
1:
2:
(HB3)
(H11) Front
Rear
Front
Rear
Front
1
12
1
1
2
1
2 2
2
1
2
1
2
2
1
2
17.6
µ19.4 oz (500 µ550 g)
12 V µND-OIL8