2007 HONDA CR-V brake

µ
µ µ
Push down on the
lever to signal a left turn and up to
signal a right turn. To signal a lane
ch ange, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
Turning the switch to
the ‘‘ ’’ position turns on the
parking lights, taillights, instrument
panel lights, side-marker lights, and
rear license plate light.
Turning the switch to the ‘‘ ’’
position turns on the headlights. If
you leave the lights on with the key
removed from the ignition switch,
you will hear a reminder chime when
you open the driver’s door. You
can change the instrument panel
brightness only when the light
switch is on.
Push the lever
f orward and the high beam indicator
will come on (see page ). Pull it
back to return to low beams.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
With the headlight switch in the of f
or position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch. Turntheknobonthelowerpartof
the instrument panel to adjust the
brightness.
You will hear a beep when maximum
or minimum brightness is reached.
63
CONT INUED
Turn Signal
Headlights
Instrument Panel Brightness
High Beams
Daytime Running L ights
Turn Signal and Headlights, Instrument Panel Brightness
Inst rument s and Cont rols
75
INSTRUMENT PANEL BRIGHTNESS
CONTROL KNOB

Push the lever under the steering
column all the way down.
Make
any steering wheel adjustment
befo re you start driving.
To apply the parking brake, push the
pedal down with your foot. To
release it, push on the pedal again.
The parking brake indicator on the
instrument panel should go out when
the parking brake is fully released
(see page ). Move the steering wheel up or
down, and in or out, so it points
toward your chest, not toward
your f ace. Make sure you can see
the instrument panel gauges and
indicators.
1.
2.
60
Parking Brake Steering Wheel A djustments
Parking Brake, Steering Wheel A djustment
78
PARKING BRAKE PEDAL
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
Driving the vehicle with the parking
brake applied can damage the rear
brakes and axles. A beeper will sound
if the vehicle is driven with the parking
brake on.

Pushandholdthefrontof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound.
Release the switch and then,
within 5 seconds, turn the ignition
switch to the LOCK (0) position.
Your vehicle has customizable
settings f or the doors and the
tailgate to automatically lock and
unlock. Make all settings bef ore you
start driving.
Make sure the shif t lever is in
Park (P), and close the driver’s
door.
Turn the ignition switch to the ON
(II) position.
Set the parking brake.
The auto door locking f eature has
three possible settings:
Thedoorsandthetailgatelock
when the vehicle speed reaches
9mph(15km/h).
This is the factory setting.
The auto door locking is
deactivated all the time.
Thedoorsandthetailgatelock
whenever you move the shif t lever
out of the Park position. 1.
2. 3.
4.
3.
Locks all doors and tailgate when the shif t lever is moved out of park (P).
A uto Door L ocking/Unlocking
A uto Door L ockingTo activate an auto door lock mode:
Door L ocks
84

Make sure the shif t lever is in
Park (P), and open the driver’s
door.
Turn the ignition switch to the ON
(II) position.
Set the parking brake.Make sure the shif t lever is in
Park (P), and close the driver’s
door.
Turn the ignition switch to the ON
(II) position.
Set the parking brake.
Pushandholdthefrontof the
master door lock switch on the
driver’s door. You will hear a
clicking sound af ter about 5
seconds.
Release the switch and then,
within 5 seconds, turn the ignition
switch to the LOCK (0) position.
1. 1.
2.
3. 2.
3.
4.
5.
Locks all doors and tailgate when the
vehicle’s speed reaches about 9 mph(15 km/h).
CONT INUED
To turn the auto door lock modesoff: To activate an auto door lock mode:
Door L ocks
Inst rument s and Cont rols
85

Release the switch and then,
within 5 seconds, turn the ignition
switch to the ACCESSORY (I)
position. Pushandholdthefrontof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound. Push and hold the brake pedal,
then move the shift lever out of
Park (P).The auto door unlocking f eature has
f ive possible settings:
Make sure the shif t lever is in
Park (P), and close the driver’s
door.
The driver’s door unlocks when
you move the shif t lever to the
Park position.
This is the factory setting.
The driver’s door unlocks
whenever you turn the ignition
switch to the ACCESSORY (I)
position.
All doors and the tailgate unlock
when you move the shif t lever to
the Park position.
All doors and tailgate unlock
whenever you turn the ignition
switch to the ACCESSORY (I)
position.
The auto door unlocking is
deactivated all the time.
Set the parking brake. Turn the ignition switch to the ON
(II) position.
4.
5.
6.
1.
2.
3.
Unlocks driver’s door when the ignitionswitch is moved out of the ON (II)position.
A uto Door UnlockingTo activate an auto door unlockmode:
Door L ocks
86
Move the shift lever to the
PARK (P) position, then turn the
ignition switch to the LOCK (0)
position.
7.

Push and hold the brake pedal,
then move the shift lever out of
Park (P).
Pushandholdtherearof the
master door lock switch on the
driver’s door. You will hear a
clicking sound. Continue to hold
down the switch:Set the parking brake. Make sure the shif t lever is in
Park (P), and open the driver’s
door.
Turn the ignition switch to the ON
(II) position.Pushandholdtherearof the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and af ter about 5
seconds, you will hear another
clicking sound.
Until you hear one click (af ter
about 5 seconds) to activate the
driver’s door unlock f eature.
Or, until you hear a second click
(af ter about 10 seconds) to
activate the all doors and tailgate
unlock f eature.
4.
4.
5.
1.
2.
3.
CONT INUED
To turn the auto door unlock modesoff:
Door L ocks
Inst rument s and Cont rols
87
Release the switch and then,
within 5 seconds, turn the ignition
switch to the ACCESSORY (I)
position.
6.
Move the shift lever to the
PARK (P) position, then turn the
ignition switch to the LOCK (0)
position.
7. Release the switch and then,
within 5 seconds, turn the ignition
switch to the LOCK (0) position.
5.

Make sure that the folded down rear
seat does not interfere with the front
passenger’s seat-back. This will
cause the front passenger’s weight
sensors and the front passenger’s
seat belt reminder indicator to work
improperly (see pages and ).
Also check the passenger airbag of f
indicator to assure proper operation
of the passenger’s front airbag. When any seat-back is f olded down,
do not use the dual deck cargo shelf
(if equipped).
Make sure all items in the cargo area
are secured. Loose items can f ly
f orward and cause injury if you have
to brake hard (See
on page ).
The lef t and right rear seats can be
f olded up separately to make room
for cargo.
Remove any items from the seat
beforeyoufolduptheseatcushion.
To f old the rear seat f orward:Pull up the bar under the seat
cushion and slide the rear seat
backward. The rear seat will not
fold forward unless it is not as far
back as it will go.
27 31
222
1.
CONT INUED
Seats
Carrying CargoFolding the Rear Seat Forward
Inst rument s and Cont rols
101
SLIDE BAR

Pull down on the anchor to engage
the upper part of the anchor
secu rely on the hook, and make
sure the seat is secure. Make
sure that the folded up right
rear seat does not interfere with the
front passenger’s seat-back. This will
cause the front passenger’s weight
sensors and the front passenger’s
seat belt reminder indicator to work
improperly (see page ). Also
check the passenger airbag off
indicator to assu re proper operation
of the passenger’s advanced front
airbag.
Reverse this procedure to return the
seat to the upright position.
Make sure the seat is securely
latched before driving.
When you are not using the
fastening strap, store the strap into
the slit on the seat-back. Make
sure both outer seat belts are
positioned in side of the rear seat-
backs.
In the center seating position of the
rear seat, be sure the deta chable
anchor is latched securely bef ore
using the seat belt (see page ).
Make sure all items in the cargo area
are secured. Loose items can f ly
f orward and cause injury if you have
to brake hard (See
on page ).
Do not use the dual deck cargo shelf
(if equipped) when the seats are
folded down or forward.
5. 104
222
32
Seats
Carrying Cargo
Inst rument s and Cont rols
103
HOOK
ANCHOR
FASTENING STRAP