2007 HONDA ACCORD SEDAN homelink

The heating and air conditioning
system in your vehicle provides a
comf ortable driving environment in
all weather conditions.
The standard audio system has
many f eatures. This section
describes those f eatures and how to
use them..............
Vents, Heating, and A/C . 102
...............
Voice Control System . 104
..........
Dual Temperature Control . 111
..............
Climate Control Sensors . 113
..........
Playing the AM/FM Radio . 114
...............
Voice Control System . 116
.....................
To Play the Radio .116
....................
To Select a Station . 116
.................
Adjusting the Sound . 119
....................
Radio Frequencies . 120
........................
Radio Reception .120
..................................
Playing a CD .122
..........
Playing a CD, CD Changer . 124
.............................
To Play a CD .124
...............
To Stop Playing a CD . 127
Removing CDs from the .................................
Changer .127
Operating the Optional CD .................................
Changer .128
.........
CD Player Error Messages . 129
.....................
Protecting your CDs .130
.................
General Inf ormation . 130
..........................
Protecting CDs .130
...............................
Playing a Tape .131
..........................
To Play a Tape .132
............
To Stop Playing a Tape . 132 ............
Tape Search Functions . 133
Caring f or the Tape and .....................................
Player .134
.
Playing the XM
Satellite Radio . 135
...............
Satellite Digital Radio . 135
....
To Play XM
Satellite Radio . 136
..................
To Select a Channel . 136
..............
Satellite Radio Signals . 138
Receiving Satellite Radio ....................................
Service .139
.............
Steering Wheel Controls . 141
.................
Radio Thef t Protection . 142
..........................
Setting the Clock .143
............................
Security System .144
...............................
Cruise Control .145
HomeLink Universal ................................
Transceiver .148
Your vehicle has an anti-theft audio
system that requires a code number
to enable it.
The security system helps to dis-
courage vandalism and thef t of your
vehicle.
All models except U.S. VP, LX, and SE,
and Canadian DX
Features
Features
101
All models except U.S. VP and LXand Canadian DX and SE

Todothis,pressandholdthetwo
outside buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
The HomeLink
universal
transceiver built into your vehicle
canbeprogrammedtooperateupto
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. If your garage door
opener was manuf actured bef ore
April 1982, you may not be able to
program HomeLink to operate it.
They do not have the saf ety f eature that causes the motor to stop and
reverse if an obstacle is detected
during closing, increasing the risk of
injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment.
For quick and accurate training,
make sure the remote transmitter
for the device (garage door,
automatic gate, security system, etc.)
has a fresh battery.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button.
If you are training the second or
third buttons, go directly to step 1.
Unplug the garage door opener
motor f rom the electrical outlet.
Holdtheendof thegaragedoor
opener remote 2 to 5 inches f rom
HomeLink.Makesureyouarenot
blocking your view of the red
indicator in HomeLink.
1.
2.
EX-V6T raining HomeL ink
General Inf ormation Important Saf ety Precautions
Bef ore you begin
HomeL ink Universal Transceiver
148
µ

Plug in the garage door opener
motor, then test the HomeLink
button by pushing it for about 1 second.
If the button works,
programming is complete.
If the button does not work go
to step 6.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. If the red indicator in HomeLink
begins to flash slowly at first,
then rapidly, release both
buttons, and go to step 5. If
the red indicator in HomeLink
continues to flash slowly (does
not flash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds.
If the red indicator in HomeLink
begins to flash slowly at first,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
continues to flash slowly (does
not begin to flash rapidly),
repeat steps 2 thru 4. Repeat
these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled devices
around your home (lighting,
automatic gate, security system,
etc.). If the indicator f lashes rapidly
f or 2 seconds then stays on, you
have a rolling code transmitter:
go to ‘‘Training with a Rolling
Code System’’ (see page ). If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
PushandholdtheHomeLink
button f or a f ew seconds, then
watch the red indicator on
HomeLink.
3. 4.
5.6.
7.
150
HomeL ink Universal Transceiver
Features
149

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure. Press the HomeLink button again
f or about 1 second. It should
operate the garage door.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes. Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
6.
2. 4.
5.
1. 3.
T raining With a Rolling Code
System
HomeL ink Universal Transceiver
150
TRAINING BUTTON

Youshoulderaseallthreecodes
before selling the vehicl e.
Toerasethecodesstoredinallthree
buttons,
press and hold the two
outside buttons until the red
indicator begins to flash, then
release the buttons.
If you want to retrain a programmed
button for a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure: If
a standard transmitter was
programmed, the indicator will
stay on for about 25 seconds.
HomeLink
is a registered
trad emark of Johnson Controls, Inc.
If
you have problems with training
the HomeLink Universal Transceiver,
or would like information on home
products that can be operated by
HomeLink, call (800) 355-3515. On
the Internet, go to
www.homelink.com. Once
the HomeLink indicator
begins to flash slowl y, continue to
hold the HomeLink button, and
f ollow steps 3 thru 6 under
‘‘Training HomeLink’’ (see page ).
If a rolling code transmitter was
previously programmed, the
indicator will f lash rapidly f or 2
seconds, and then stay on f or
about 23 seconds.
Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly.
1. 2.
148
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Erasing Codes
Retraining a Button Customer Assistance
HomeL ink Universal Transceiver
Features
151

CONT INUED
...................................
Fan, Interior .104
.........................................
Features .101
....................
Filling the Fuel Tank . 156
........................................
Filter, Oil .206
5-speed Manual Transmission ...............
Checking Fluid Level . 213
................................
Shif ting the .170
.............
Flashers, Hazard Warning . 71
...................
Flat Tire, Changing a . 241
Fluids .
Automatic Transmission . 211, 212
..........................................
Brake .215
.........................................
Clutch .215
......
Manual Transmission . 213, 214
..........................
Power Steering .216
..................
Windshield Washer . 210
...........................
Folding Rear Seat .88
..........................
Four-way Flashers .71
.................................................
Fuel .154
...............................
Cap Message .66
......................
Fill Door and Cap .156
...........................................
Gauge .66
................
Octane Requirement . 154
........................
Tank, Filling the .156 .....................
Fuses, Checking the .257
...............
Gas Mileage, Improving . 161
.........................................
Gasoline .154
...........................................
Gauge .66
................
Octane Requirement . 154
........................
Tank, Filling the .156
................
Gas Station Procedures . 156
Gauges ...
Engine Coolant Temperature . 65
...............................................
Fuel .66
...............................
Speedometer .64
.................................
Tachometer .64
Gearshif t Lever Positions ..........
Automatic Transmission . 173
..............
Manual Transmission . 170
......................................
Glove Box .100
.............
Halogen Headlight Bulbs . 218
..............
Hazard Warning Flashers . 71
........................................
Headlights .69
........................................
Aiming .218 ..............
Automatic Lighting Off . 70
............
Daytime Running Lights . 70
............
Low Beams, Turning on . 69
.........................
Reminder Chime .69
........
Replacing Halogen Bulbs . 218
...................................
Turning on .69
........................
Head Restraints . 15, 87
.....................
Heating and Cooling .102
.................................
Heated Mirror .91
HomeLink Universal ................................
Transceiver .148
..
Hood, Opening and Closing the . 157
...........................
Hydraulic Clutch .215
...
Identif ication Number, Vehicle . 266
Ignition ..............................................
Keys .74
...........................................
Switch .76
............
Timing Control System . 275
........................
Immobilizer System .75
.........
Important Safety Precautions . 8
.........
Indicators, Instrument Panel . 58
Index
F
G
HI
INDEX
III