2007 HONDA ACCORD Radio

To load or play CDs, the ignition
switch must be in the ACCESSORY
(I) or the ON(II) position.
You operate the CD player/CD
changer with the same controls used
for the radio. To select the CD
player/CD changer, press the CD
button. The number of the track
playing is shown in the display. With
the in-dash CD changer, the disc and
track numbers are displayed. The
system will continuously play a CD
until you change modes.To listen to satellite radio when a CD
is playing, press the CD/AUX XM
button.
To play the radio when a CD is
playing, press the AM/FM button.
Press the CD button again to switch
back to the CD player.
Insert a CD about half way into the
CD slot. The drive will pull the CD in
the rest of the way and begin to play
it. When the system reaches the end
of the disc, it will return to the
beginning and play the disc again.
To play a tape when a CD is playing,
insert a tape in the player (optional).
If a tape is in the player, press the
CD/AUX button. Press the CD/AUX
button again to switch back to the
CD player.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .
Vehic les witho ut in-dash CD c hang er
Vehic les with satellite radioTo Play a CD
Playing a CD, CD Changer
124
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
——
y

y
(y
y

µµ´
Û
Ý
Press the LOAD button until you
hear a beep and see ‘‘LOAd’’ in the
display.
The disc number f or an empty
position is highlighted and the red
light starts blinking.
When the CD load indicator turns
green and ‘‘LOAD’’ appears in the
screen again, insert the next CD in
the slot.
Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, the
system begins playing the last CD
loaded. You can also load a CD into an empty
position while a CD is playing. Select
the empty position (the disc number
indicator is not highlighted) and
press the appropriate preset bar or
touch a disc icon. The current CD
stops playing and starts the loading
sequence. The CD just loaded will
play.
You operate the CD changer with
the same controls used f or the radio.
The numbers of the disc and track
playingareshowninthedisplay.On
vehicles with navigation system,
these numbers also appear in the
upper display.
To select a dif f erent disc, press the
appropriate side of a preset bar
(1 6) or use the Preset 5 (DISC )
to select the previous disc or Preset
6 (DISC ) to select the next disc in
sequence. On vehicles with
navigation system, touch the
appropriate disc icon or press the
or side of the CH/DISC bar. If
youselectanemptypositioninthe
CD changer, the system will try to
load the CD in the next available slot.
Insert the disc into the CD slot
when the green CD load indicator
comes on. Insert it only about
half way; the drive will pull it in the
rest of the way. You will see
‘‘BUSY’’ in the display as the CD
load indicator turns red and blinks
as the CD is loaded.
1. 2.3. 4. 5.
CONT INUED
Vehic les with in-dash CD c hang er
Vehic les with in-dash CD c hang er
Playing a CD, CD Changer
Features
125
——
y

y
(y
y

µµ
µ Touch the icon to
continuously replay the current CD.
Touch again to turn it of f .
Touch the icon to
play the current CD in random order.
Touch again to stop.
Selects an icon and
plays the disc.
If you turn the system of f while a CD
is playing, the CD will stay in the
drive. When you turn the system
back on, the CD will begin playing
where it lef t of f .
Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button. PresstheAM/FMorCD/AUX/XM
button to switch to the AM/FM
radio or satellite radio while a CD is
playing. To play the CD, press the
CD/AUX/XM button again.
If a tape is in the optional tape player,
press the CD/AUX button to switch
to the tape while a CD is playing.
Press the CD/AUX button again to
switch back to the CD player.
To remove the disc currently playing,
press the EJECT button. When a
disc is removed f rom a slot, the
system automatically begins the load
sequence so you can load another
CD in that position. If you do not
remove the disc f rom the changer
within 15 seconds, the system
returns to the previous mode (AM/
FM or satellite radio). The disc will
reload into the system and will
remainthereinapausemode.
To remove a dif f erent disc f rom the
changer,firstselectitwiththe
appropriate preset bar or icon. When
that CD begins playing, press the
eject button. Continue pressing the
EJECT button to remove all the discs
f rom the changer.U.S. EX-L and EX-V6
Except U.S. VP, LX, and Canadian DX-GDISC RPT
TRACK RDM
CH DISC
To Stop Playing a CD Removing CDs f rom the Changer
Playing a CD, CD Changer
Features
127
——
y


y
(y
y

µ´
Load the desired CDs into the
magazine, and load the magazine
into the changer according to the
instructions that came with the unit.
To select the CD changer, press the
CD button. The disc and track
numbers will be displayed. To select
a dif f erent disc, use Preset 5 (DISC
), f or a previous disc; or Preset 6
(DISC ), to select the next disc in
sequence.
If you select an empty slot in the
magazine, the changer will search
f or the next available CD to load and
play.
An optional six or eight disc CD
changer is available f or your vehicle
f rom your dealer.
This disc changer uses the same
controls used f or the in-dash CD
player/changer or the radio.
U.S. VP and LX, and Canadian DX-G
Operating the Optional CD
Changer
Playing a CD, CD Changer
128
——
y


y
(y
y

Playing a T ape (U.S. Vehicles)
Features
131
PWR/VOL KNOBAUDIO
DISPLAY
BUTTON
CD/AUX
BUTTON
RPT
BUTTON
RPT INDICATOR
PRESET BARS
PROG ICONNR ICON
RPT ICON TAPE DIRECTION INDICATOR
SEEK/SKIP
BAR U .S. EX -L and EX -V 6 w it h navigat ion syst em
PWR/VOL KNOB
CD/AUX
BUTTON
SEEK BAR TAPE DIRECTION INDICATOR
UPPER
DISPLAY
CH/DISC
BAR
RPT INDICATOR
CD/SAT RADIO
BUTTON
PWR/VOL KNOB
RPT INDICATOR
RPT
BUTTON
PRESET BARS
US. VP and LX
TAPE DIRECTION INDICATOR
U.S.SE,EX,LX-V6,andSE-V6
U.S. EX-L and EX-V
6 w it hout navigat ion syst em
SEEK BAR
——
y

y
(y
y

Û
Î
Î
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Make sure the open side of the tape
is facing right, then insert the tape
most of the way into the slot. The
system will pull the tape in the rest
of the way, and begin to play it.
The tape direction indicator will light
to show you which side of the tape is
playing. The indicates the side
youinsertedupwardinnowplaying.
If you want to play the other side,
press the Preset 3 (PLAY/PROG)
side of the preset bar or press the
AUDIO DISPLAY button and touch
the PROG icon. When the player
reaches the end of the tape, it will
automatically reverse direction and
play the other side. Dolby noise reduction turns on
when you insert a tape. The
indicator will light in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the
Preset 4 (NR) side of the preset bar
or touching the NR icon. Dolby
remains of f until you press the
preset bar or the icon again.
Dolby noise reduction
manuf actured under license f rom
Dolby laboratories licensing
Corporation. ‘‘Dolby’’ and the
double-D symbol are trademarks
of the Dolby Laboratories
Licensing Corporation. To remove the tape, press the
EJECT button on the cassette player.
If you want to turn the player of f ,
press the PWR/VOL knob or turn
of f the ignition. The tape will remain
in the drive.
When you turn the system back on,
the tape player will be in pause mode.
Press the Preset 3 (PLAY/PROG)
side of the preset bar or touch the
PROG icon on vehicles with
navigation system to resume play.
To switch to the radio or CD player
while a tape is playing, press the
AM/FM, or CD/AUX button or CD/
AUX XM button. To change back to
thetapeplayer,pushtheCD/AUX
button or CD/AUX XM button.
Optional on all U.S. models
To Play a Tape
To Stop Playing a Tape
Playing a T ape (U.S. Vehicles)
132
——
y

y
(y
y

XMis a registered trademark of
XM Satellite Radio, Inc.
Your vehicle is capable of receiving XM
Satellite Radio anywhere in the
United States, except Hawaii and
Alaska.
U.S. EX-L and EX-V6
Satellite Digital Radio
Playing t he XMSatellite Radio
Features
135
DISP
BUTTON
SAT RADIO
BUTTON
SCAN
BUTTON SCAN
BUTTON
TUNEKNOB
TUNE
BAR
CATEGORY/CHANNEL
MODE INDICATOR
CATEGORY/CHANNEL
MODE INDICATOR
MODE ICON
SCAN ICON
PWR/VOLKNOB
SAT RADIO
BUTTON
PWR/VOL KNOB AUDIO
DISPLAY
BUTTON
PRESET
BARS PRESETICONS
U.S. EX-L and EX-V6
w it hout navigat ion syst em
U .S. EX -L and EX -V 6
w it h navigat ion syst em
SEEK/SKIP
BAR SEEK/SKIP
BAR
——
y

y
(y
y

µ
µ
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position.
Turn the system on:
Press the TUNE bar to change
channel selections. Press f or
higher numbered channels andf or lower numbered channels.
Turn the TUNE knob to change
channels. Turn the knob right f or
higher numbered channels and lef t
f or lower numbered channels.
Press and release this button to
change the display. The display will
change in the f ollowing sequence:
channel name, channel number,
category, artist name, and music title.
When in the satellite radio mode,
you can use any of three methods to
f ind channels: TUNE, SEEK/SKIP
(CATEGORY), and SCAN.
Turn the PWR/VOL knob to adjust
the volume.
Push any of the f ollowing: PWR/
VOL knob or the CD/AUX XM
button.
Push any of the f ollowing: PWR/
VOL knob, the CD/AUX XM, or
AUDIO button.
Witho ut navig atio n system
Witho ut navig atio n system
With navig atio n system With navig atio n system

With navig atio n system
TUNE
DISP
T o Select a Channel
To Play XMSatellite Radio
Playing t he XMSatellite Radio
136
——
y


y
(y

y