2007 HONDA ACCORD COUPE reset

µµ
µ The seek f unction
searches up and down f rom the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar, then release it.
The scan f unction samples
all stations with strong signals on the
selected band. To activate it, touch
the SCAN icon. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, touch
the SCAN icon again.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
PWR/VOL knob or the AM/FM
button. Adjust the volume by turning
the PWR/VOL knob.
Pushing the AUDIO DISPLAY
button will also turn on the system.
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, the
preset icons, and AUTO SELECT.
Use the TUNE/SOUND
knob to tune the radio to a desired
f requency. Turn the knob right to
tune to a higher f requency, and turn
the knob lef t to tune to a lower
f requency.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction in
AM is not available.
For inf ormation on XM satellite radio,
see page .
153 SEEK
SCAN
T o Play the A M/FM Radio T o Select a Station
TUNE
A M/FM/CD Changer
150
——y

y
(#y
y

µ
µ
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Each preset icon can store
one f requency on AM, and two
f requencies on FM.
Touch the AUTO SELECT icon.
‘‘A. SEL’’ f lashes in the upper display,
and the system goes into scan mode
f or several seconds. It stores the
f requencies of six AM, and twelve
FM stations in the preset icons.You will see a ‘‘0’’ displayed af ter
pressing a preset icon if auto select
cannot f ind a strong station f or every
preset icon.
If you do not like the stations auto
select has stored, you can store
other f requencies on the preset icons
as previously described.
To turn off auto select, touch the
AUTO SELECT icon. This restores
the presets you originally set.
Push the AUDIO DISPLAY button
to see the preset icons Then select
the desired band, AM or FM. FM1
and FM2 let you store two
f requencies with each preset icon.
Usethetune,seek,orscan
function to tune the radio to a
desired station.
Pick the preset icon you want f or
that station. Touch the icon, and
hold it until you hear a beep. The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
1. 2. 3. 4.
AUTO SELECT
Preset
A M/FM/CD Changer
Features
151
——y

y
(#y
y

XMis a registered trademark of
XM Satellite Radio, Inc.
Your vehicle is capable of receiving XM
Satellite Radio anywhere in the
United States except Hawaii and
Alaska. It is not available in Canada.
Satellite radio is available on U.S.
models only.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position.
Turn the system on by pushing the
PWR/VOL knob, the CD/AUX/XM,
or AUDIO button.
Turn the PWR/VOL knob to adjust
the volume.
U.S. models
A M/FM/CD Changer
To Play XMSatellite Radio
XM
Satellite Radio
Features
153
SCAN ICON
MODE ICON
CHANNEL INDICATOR
SEEK/SKIP BAR
SCAN BUTTON
PWR/VOL KNOB TUNE KNOB
CH/DISC BAR
PRESET ICONS
U.S. EX-L and EX-V6 models with navigation system
CD/AUX/XM
BUTTON
AUDIO BUTTON
——y
y
(#y
y

µ
µ
µ µ
µ Each preset icon can store
one channel in XM1 and one in XM2.
Pick a preset icon, and hold it until
you hear a beep.
Repeat steps 1 through 3 to store a
total of six stations on XM1 and
six on XM2.
The
seek/skip f unction selects the
various categories in XM, such as
Jazz/Blues, Rock, Classical, etc.
Push the to change the
category f orward. Push the to
change the category backward. To
search f or channels within a
category, turn the TUNE knob
clockwise.
Once your XM channels are preset,
pressing either side of the CH/DISC
bar will select your preset channels.
When in the satellite radio mode,
you can use any of f our methods to
f ind channels: TUNE, SEEK/SKIP
(CATEGORY), SCAN, and the
preset icons.
Turn the TUNE knob to change
channels. Turn the knob right f or
higher numbered channels and lef t
f or lower numbered channels.
Push the CD/AUX/XM button.
(You will see XM1 or XM2.)
To switch between
channel mode and category mode,
touch the MODE icon.
The scan f unction samples
all channels f or 5 seconds. To
activate the f unction, push the SCAN
button. Push it again to get out of the
sequence. Usethetune,seek,orscan
function to tune the radio to a
desired station.
1. 2. 3. 4.
Preset
SEEK /SK IP (CA T EGORY)
T o Select a Channel
TUNE
MODE
SCAN
A M/FM/CD Changer
154
——y

y
(#y
y

ÛÝ´
µ ´
µ
´ µ
The VOL button adjusts the volume
up ( ) or down ( ). Press the top
or bottom of the button, hold it until
the desired volume is reached, then
release it.
If you are listening to the radio, use
the CH button to change stations.
Each time you press the top ( ) of
the button, the system goes to the
next preset station on the band you
are listening to. Press the bottom
( ) to go back to the previous
station. If youareplayingaCD,thesystem
skips to the beginning of the next
track each time you press the top
( ) of the CH button. Press the
bottom ( ) to return to the
beginning of the current track. Press
it twice to return to the previous
track. You will see the disc and track
numbers in the display.
If youareplayingatapeinthe
optional tape player, press the top
( ) of the CH button to advance to
the next selection. Press the bottom
( ) to go back to the previous
selection. The system senses a silent
period, then resumes playing.
The MODE button changes the
mode. Pressing the button
repeatedly selects FM1, FM2, AM,
CD (if a CD is loaded), or a tape (if
equipped). On models with satellite
radio system, you can also select
XM1 and XM2.
Three control buttons f or the audio
system are mounted in the steering
wheel hub. These buttons let you
control basic audio f unctions without
removing your hand f rom the wheel.
On all models except the 4-cylinder LX
Remote Audio Controls
Features
171
VOL BUTTON MODE BUTTON
CH BUTTON
——y
y
(#y
y

µ
Youshouldhavereceivedacardthat
lists your audio system’s code and
serial numbers. It is best to store this
card in a saf e place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual. If you make a mistake entering the
code, do not start over; complete the
sequence, then enter the correct
code. You have ten tries to enter the
correct code. If you are unsuccessf ul
in ten attempts, you must then leave
the system on f or 1 hour bef ore
trying again.You will have to store your favorite
stations on each side of the preset
bars (1 6) or icons af ter the system
begins working. Your original
settings were lost when the power
was disconnected.
If you lose the card, you must obtain
the code number f rom a dealer. To
do this, you will need the system’s
serial number.
Your vehicle’s audio system may
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic code using the preset
bars or the TUNE knob. Because
there are hundreds of number
combinations possible, making the
system work without knowing the
exact code is nearly impossible.
If your vehicle’s battery is
disconnected or goes dead, or the
radio f use is removed, the audio
system may disable itself . If this
happens, you will see ‘‘ ’’/
‘‘ ’’ in the f requency display
the next time you turn on the system.
Use the preset bars to enter the code.
Thecodeisontheradiocodecard
included in your owner’s manual kit.
When it is entered correctly, the
radio will start playing.
On models except the 4-cylinder LX
Radio T hef t Prot ect ion
172
——y
y
(#y
y

The upper display shows the time
when the ignition switch is in the
ACCESSORY (I) or ON (II) position.
The navigation system receives
signals f rom the Global Positioning
System (GPS), and the displayed
time is updated automatically by the
GPS. Ref er to the navigation system
owner’s manual to set up the time.
To set the time, press the clock set
(SOUND) button until you hear a
beep. The displayed time begins to
blink.
Press and hold the H (preset 4) side
of the bar until the hour advances to
the desired time. Press and hold the
M (preset 5) side of the bar until the
minutes advance to the desired time.
Press the clock set (SOUND) button
again to enter the set time.
You can quickly set the time to the
nearest hour. If the displayed time is
bef ore the half hour, pressing the
clock set (SOUND) button until you
hear a beep, then pressing the R
(preset 6) side of the bar sets the
clockbacktotheprevioushour.If
the displayed time is after the half
hour, the clock sets f orward to the
beginning of the next hour.
For example:
1:06 will reset to 1:00
1:53 will reset to 2:00
If your vehicle’s battery is
disconnected or goes dead, you may
need to set the clock.
On models without navigation system
On models with navigation system
Setting the Clock
Features
173
CLOCK SET BUTTON
PRESET BARS
CLOCK
EX-L and EX-V6 models without navigation system is shown.
——y
y
(#y
y

Once the security system is set,
opening either door without using
the key or the remote transmitter,
the hood, or the trunk will cause the
system to alarm. It also alarms if the
radio is removed f rom the dashboard
or the wiring is cut.With the system set, you can still
open the trunk with the remote
transmitter without triggering the
alarm. The alarm will sound if the
trunk lock is f orced, or the trunk is
opened with the trunk release handle
or the emergency trunk opener.
The security system will not set if
the hood, trunk, or either door is not
f ully closed. Bef ore you leave the
vehicle, make sure the doors, trunk,
and hood are securely closed.
To see if the system is set
af ter you exit the vehicle, press the
LOCK button on the remote
transmitter within 5 seconds. If the
system is set, the horn will beep
once.
Do not attempt to alter this system
or add other devices to it.
The security system automatically
sets 15 seconds after you lock the
doors, hood, and trunk. For the
system to activate, you must lock the
doors f rom the outside with the key,
lock tab, door lock switch, or remote
transmitter. The security system
indicator on the instrument panel
starts blinking immediately to show
you the system is setting itself .
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights (low beam), parking
lights, side marker lights, and
taillights f lash if someone attempts
to break into your vehicle or remove
the radio. This alarm continues f or 2
minutes, then it stops. To reset an
alarming system bef ore the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
All models except LX
Security System
174
NOTE:
SECURITY SYSTEM INDICATOR
——y
y
(#y
y