2007 HONDA ACCORD COUPE turn signal

µ
µ µ
Push down on the
lever to signal a lef t turn and up to
signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
Turn signal
Of f
Parking and interior lights
Headlights
High beams
Flashhighbeams Turning the switch to the ‘‘ ’’
position turns on the headlights. If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
When the light switch is in the
‘‘ ’’ or ‘‘ ’’ position, the
lights on indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position. Turning the switch to
the ‘‘ ’’ position turns on the
parking lights, taillights, instrument
panel lights, side-marker lights, and
rear license plate lights. Push the lever
f orward and the high beam indicator
will come on (see page ). Pull it
back to return to low beams.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
1.2.3.4.5.6. 60
Turn Signal
Headlights
High Beams
Turn Signal and Headlights
Inst rument s and Cont rols
69
——y
y
(#yy

instrument panel controls the
brightness of the instrument panel
lights. Turn the knob to adjust the
brightness.Push the button between the center
vents to turn on the hazard warning
lights (f our-way f lashers). This
causes all f our outside turn signals
and both turn indicators in the
instrument panel to f lash. Use the
hazard warning lights if you need to
park in a dangerous area near heavy
traf f ic, or if your vehicle is disabled.
The instrument panel will illuminate
with reduced brightness when you
open the driver’s door. The
brightness will increase slightly
when you insert the key in the
ignitionswitch,thengotonormal brightness when you turn the
ignition switch to the ON (II)
position.
If you do not insert the key in the
ignition switch af ter opening the
driver’s door, the illumination turns
of f about 30 seconds af ter you close
the door.
If you insert the key but do not turn
the ignition switch to the ON (II)
position, the illumination turns of f in
about 10 seconds.
To reduce glare at night, the instru-
ment panel illumination dims when
you turn the light switch to or
knob f ully to the right until you hear
a click will cancel the reduced bright-ness.
Instrument Panel Brightness
Hazard Warning Button
Instrument Panel Brightness, Hazard Warning Button
Inst rument s and Cont rols
71
SELECT/RESET KNOB
——y
y
(#yy
The select/reset knob on the
. Turning the select/reset

µµ
µ The seek f unction
searches up and down f rom the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar, then release it.
The scan f unction samples
all stations with strong signals on the
selected band. To activate it, touch
the SCAN icon. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, touch
the SCAN icon again.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
PWR/VOL knob or the AM/FM
button. Adjust the volume by turning
the PWR/VOL knob.
Pushing the AUDIO DISPLAY
button will also turn on the system.
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, the
preset icons, and AUTO SELECT.
Use the TUNE/SOUND
knob to tune the radio to a desired
f requency. Turn the knob right to
tune to a higher f requency, and turn
the knob lef t to tune to a lower
f requency.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction in
AM is not available.
For inf ormation on XM satellite radio,
see page .
153 SEEK
SCAN
T o Play the A M/FM Radio T o Select a Station
TUNE
A M/FM/CD Changer
150
——y

y
(#y
y

If you decide to purchase XM
satellite radio service, contact XM
Radio at , or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number.
To get your radio I.D. number:
Turn the TUNE knob or press the
TUNE bar until ‘‘0’’ appears in the
display. Your I.D. will appear in the
display.After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.
While waiting f or activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated, ‘‘category’’
or ‘‘CH’’ will appear in the display,
andyou’llbeabletolistentoXM
Radio broadcasts. XM Radio will
continue to send an activation signal
to your vehicle for at least 12 hours
from the activation request. If the
service has not been activated after
36 hours, contact XM Radio.
www.xmradio.com
XMSatellite Radio Reception
168
——y
y
(#y
y

Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the air intake duct
securely.
(Driver’s side)
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter. To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.
Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the inner f ender cover away
f rom the f ender and bumper.
1.
3.
2. 4.
9.
7.
8.
11.
10.
CONT INUED
On EX-V6 model with manual
transmission
Replacing a Front Side Marker/
Parking/Turn Signal Light Bulb
Lights
Maint enance
249
HOLDING CLIPS
——y
y
(#yy

Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.Determine which bulb is burned
out: turn signal or back-up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Turn on the lights to make sure
the new bulb is working.
Install the light assembly cover.
Make sure it snaps into place.
1. 3.
2. 4. 5.6. 7.
5. 6. 7. 8. 9.
Replacing Rear Bulbs
Lights
250
COVER
——y
y
(#yy

µ
µ µµ µ µµµµµµµ µ µ
Î
Î
ÎÎ
ÎÎ
Specif ications (4-cylinder Models)
T echnical Inf ormation
291
Engine
Lights Battery
Fuses Alignment
Tires
12 V 24/2.2 CP
12 V
12 V
60 W (HB3)
51 W (HB4)
12 V 21 W 3.43 x 3.90 in (87.0 x 99.0 mm)
144 cu-in (2,354 cm
)
9.7 : 1
Type
BorexStroke
Displacement
Compression ratio
Spark plugs
Headlights
Front turn signal/parking/side
marker lights
Rear turn signal lights
Back-up lights
License plate lights
Ceiling light
Trunk light
Door courtesy lights
Vanity mirror lights
Spotlights 12 V 18 W
12 V 3 CP
12 V 8 W
12 V 5 W
12 V 2 CP
12 V 1.1 W
12 V 8 W
Capacity 12 V 38 AH/5 HR 12 V 47 AH/20 HR
Interior
Under-hood Water cooled 4-stroke DOHC i-VTEC
4-cylinder gasoline engine
See page 284 or the fuse label
attached to the inside of the fuse
box lid.
See page 283 or the fuse box
cover. P205/60R16 91V
Toe-in
CamberCaster Size
Pressure
3°15’
1°
0°
0.08 in (2.0 mm)
0.00 in (0.0 mm)
NGK:
DENSO:
SKJ20DRM13
SKJ20DRM11
IZFR6K13
IZFR6K11
T135/90D15 100M
32 psi (220 kPa , 2.2 kgf/cm
)
30 psi (210 kPa , 2.1 kgf/cm)
60 psi (420 kPa , 4.2 kgf/cm)
Front Rear
FrontRear
Front
HighLow
2 : Californian models with automatic transmission
1 : All models except Californian models with automatic transmission Front/Rear
Spare
FrontRear
Spare
12
12
——y
y
(#yy

µ
Î Î
µµµ µ µµµµµµµ µ µ
ÎÎ
Specif ications
T echnical Inf ormation
293
Engine
Alignment
Lights Battery
Fuses
Tires
12 V
12 V
12 V
12 V
51 W (HB4)
24/2.2 CP
21 W
3.39 x 3.39 in (86.0 x 86.0 mm)
183 cu-in (2,997 cm
)
10.0 : 1
0.00 in (0.0 mm)
0.08 in (2.0 mm) 0°1°
3°15’
Type
BorexStroke
Displacement
Compression ratio
Spark plugs
Toe-in
CamberCaster
NGK:
DENSO:
IZFR6K11SKJ20DRM11
Headlights
Front turn signal/parking/side
marker lights
Rear turn signal lights
Back-up lights
License plate lights
Ceiling light
Trunk light
Door courtesy lights
Vanity mirror lights
Spotlights
12 V 18 W
12 V 3 CP
12 V 8 W
12 V 5 W
12 V 2 CP
12 V 1.1 W
12 V 8 W
Capacity 12 V
12 V
65 AH/20 HR
52 AH/5 HR
Interior
Under-hood P215/50R17 93V
Size
Pressure T135/90D15 100M
T135/80R16 101M
32 psi (220 kPa , 2.2 kgf/cm
)
29 psi (200 kPa , 2.0 kgf/cm)
60 psi (420 kPa , 4.2 kgf/cm)
See page 284 or the fuse label
attached to the inside of the fuse
box lid.
See page 283 or the fuse box
cover. 60 W (HB3)
Water cooled 4-stroke
SOHC VTEC
6-cylinder (V6) gasoline engine
FrontRear
FrontRear
Front
HighLow
1:2:LX-V6, EX-V6 with automatic transmission
EX-V6 with manual transmission Front/Rear
Spare
Front Rear
Spare
12
——y



y
(#yy
(
V6 Models )