2007 GMC YUKON sensor

Getting to Know YourYukon/Yukon Denali18
The cruise
control buttonsare located onthe steeringwheel.
(On/Off):Press this but
ton to turn the
cruise controlsystem on
or off.
+ RES (Resume):Press this button to
resume a set speed, or to increase thespeed if the system is set.
– SET (Set):Press this button to set a
speed, or to decrease the speed if thesystem is set. When the cruise control
speed is set, the cruise light will illuminate in the instrument cluster.
(Cancel): Press this button to can
cel the cruise control but retain the set
speed in memory.
See Section 3 of your Owner Manual.
The Rainsense II windshield wipers use
a moisture sensor to automatically operate the wipers when needed, depending
on driving conditions and the sensitivity
setting. If the system is left on for longperiods, an occasional wipe may occurwithout any moisture on the windshieldto indicate the system is activated.
The headlamps also will be turned on
automatically when the Rainsensewipers are active if the exterior lamp
control switch is in the AUTO position.
Windshield Wiper Controls
The controls for the windshield wipers
are located on the multifunction stalk on
the left side of the steering column. Theband can be rotated to the followingpositions:
(Mist):Rotate the wipers band
down to this position to turn the wiperson for one wipe.
(Off):Rotate the wipers band to this
position to turn the wipers off.
(Sensitivity Setting):Rotate the
control band up to one of the sensitivity
levels to activate the Rainsense func
tion. The position closest to Off is thelowest sensitivity level.
(Low):Rotate the wipers band up
to this position to turn on the wipers tothe Low speed setting.
(High):Rotate the wipers band
up to this position to turn on the wipersto the High speed setting.
(Washer):Push the paddle on top
of the multifunction lever to spray washer fluid on the windshield.
See Section 3 of your Owner Manual.
Cruise Control (if equipped)
Rainsense™ II Windshield
Wipers (if equipped)

19
Press the (Heated Washer Fluid)
button, located below the climate controls on the instrument panel, to sprayheated washer fluid on the windshield.This will help to clear ice, tree sap orbugs from the windshield. A light on the
switch will flash while the washer fluid is
heating, which may take up to 40 seconds. The wipers will automatically turn
on for four cycles or until the button ispressed again.
See Section 3 of your Owner Manual.
The rear vision camera displays a view
of the area behind the vehicle on thenavigation screen when the vehicle isshifted into Reverse. Once shifted out ofReverse, the navigation screen willreturn to the last screen displayed afterapproximately 10 seconds.
To turn the camera on or off:
1.Shift into Park.
2. Press the Menu hard key to enter the
Menu options.
3.Press the Menu hard key to select
Display, or touch the Display screenbutton.
4. Touch the Rear Camera Options
screen button.
5.Touch the Rear Camera Image in
Reverse screen button.
To clean the camera lens, located above
the license plate, rinse it with water andwipe it with a soft cloth.
See Section 2 of your Owner Manual.
Your vehicle is equipped with an
Automatic Headlamp System, which
turns on the Daytime Running Lamps
(DRL) during the day and the head
lamps and other exterior lamps at night
or when necessary.
The system uses a light sensor, located
on top of the instrument panel, to determine light conditions. For proper systemoperation, avoid placing any objects on
or near the sensor.
Exterior Lamp Controls
The exterior lamps control knob is locat
ed on the instrument panel to the left ofthe steering wheel.
(Off):When operating in the AUTO
position, a momentary turn of the knob
to the Off position will turn off theAutomatic Headlamp System and allexterior lights, excluding the DRLs.
AUTO (Automatic):Automatically turns
on the DRLs in the daytime and theAutomatic Headlamp System at night or
when necessary.
(Parking Lamps):Manually turns
on parking lamps and taillamps.
(Headlamps):Manually turns on
the headlamps and other exterior lamps.
(Fog Lamps)(if equipped): Press
this button to turn the fog lamps on or
off.
Heated Windshield Washer Fluid
(if equipped)
Rear Vision Camera
(if equipped)
Automatic Headlamp System

Getting to Know YourYukon/Yukon Denali22
This feature uses ultrasonic sensors on
the rear bumpers to help you avoid col
liding with objects when parking the
vehicle. It operates only at speeds lessthan 3 mph.
The rear parking assist display is locat
ed near the rear window. The lights onthe display provide distance information.Lowtoned beeps play out of the rearspeakers (for objects near the rearbumper).
To turn off the system, press the disable
button located below the climate con
trols on the instrument panel. The indi
cator light will illuminate when the system is off.
See Section 3 of your Owner Manual.
The Universal Home Remote is a com
bined universal transmitter and receiverthat can activate up to three devices,such as garage door openers, entrydoor locks, gates and security systems.
It’s recommended that you read the
instructions in your Owner Manual com
pletely before attempting to program anyof the three channels on the Universal
Home Remote. The engine should be
turned off when programming theremote.
See Section 2 of your Owner Manual.
Ultrasonic Rear Parking Assist
(if equipped)
StabiliTrak is an advanced computer
controlled vehicle stability and tractionenhancement system that assists withdirectional control of the vehicle in
difficult driving conditions. It turns onautomatically every time you start your
vehicle.To limit wheelspin and help maintain directional control, you shouldalways leave the system on. However, if
your vehicle becomes stuck and rocking
StabiliTrak®– Stability Control
System (if equipped)
PERFORMANCE & MAINTENANCE
Universal Home Remote
(if equipped)
Note: Do not use the Universal Home
Remote with any garage door opener thatdoes not have the “stop and reverse” fea
ture or any opener manufactured beforeApril 1, 1982.
6Speed Automatic
Transmission Controls (Denali Models only)
The 6speed automatic transmission has
a unique gear range selection modecalled Driver Shift Control that enablesthe driver to select the range of gearsdesired for the current driving conditions,such as when driving on downhill grades.
To use this feature, move the shift lever
to the Manual (M) position and select alower or higher driving gear using the
+ / – button on the shift lever. The dis
play on the instrument panel cluster will
show the current gear selection.
Press the – (minus) side of the button to
downshift. When slowing to a stop, thevehicle will automatically downshift.
Press the + (plus) side of the button to
upshift. As vehicle speed increases, youwill need to manually upshift.
If current vehicle speed is too high or
too low for the requested gear, the shift
will not occur.
See Section 2 of your Owner Manual.