2007 FORD FIESTA ECU

303-01 B-100 Engine - 2.OL Duratec-HE (M14) 303-01 B-I 00
ASSEMBLY
29. Install the timing chain tensioner.
30. Install the timing chain guides.
31 ' ACAUTION:D~ not fully tighten the
camshaft sprocket retaining bolts at this
stage. Make sure the camshaft sprockets
turn on the camshafts.
Install the camshaft sprockets.
Install the timing chain.
32. Tension the timing chain.
Apply pressure to the timing chain and
remove the securing pin.
,
33m ACAUTION:H~I~ each camshaft by the
hexagon with an open-ended wrench to
stop
it from turning.
Tighten the camshaft sprockets retaining
bolts.
34. Clean the mating face of the engine front
cover with a suitable metal surface cleaner.
35. N0TE:lnstall the engine front cover within
10 minutes of applying the sealant.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

303-01 B-I 02 Engine - 2.OL Duratec-HE (M14) 303-01 B=102
ASSEMBLY
Using the crankshaft pulley retaining bolt, Stage 2: 90 degrees.
rotate the crankshaft until piston No. 1 is at
TDC.
39. Remove the crankshaft pulley retaining
bolt.
Discard the bolt.
40m &AUTION:O~I~ tighten the crankshaft
pulley securing bolt finger tight.
Install the crankshaft pulley onto the
crankshaft and secure the crankshaft pulley
to the front cover using a
M6 x 18 mm bolt.
41.
N0TE:lnstall a new crankshaft pulley
retaining bolt.
Using the special tools, prevent the
crankshaft pulley from rotating and tighten
the crankshaft pulley retaining bolt.
Tighten, the bolt in two stages.
Stage 1: 100 Nm.
42. Remove the crankshaft pulley securing bolt.
'.
43. Remove the special tool.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

303-01 B-103 Engine - 2.OL Duratec-HE (M14) 303-01 B-I 03
ASSEMBLY
44. Remove the special tool.
Using a M6 x 18 mm bolt, check the position
of the crankshaft pulley.
45. N0TE:Only rotate the crankshaft in the
normal direction of rotation.
49. N0TE:lf it is not possible to install the
Rotate the crankshaft two revolutions. special tool,
correct the engine timing.
46. Install the special tool. Using the special tool,
check the position of
the camshafts.
47. N0TE:Only rotate the crankshaft in the
normal direction of rotation. 50. Remove the special tool.
Rotate the crankshaft until piston No.
I is at
TDC.
48m ACAUTION:O~I~ tighten the crankshaft
pulley securing bolt finger tight.
N0TE:lf it is not possible to install the crankshaft
pulley securing bolt, correct the engine timing.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

303-01 B-I 04 Engine - 2.OL Duratec-HE (M14) 303-01 B-I 04
ASSEMBLY
51. Remove the crankshaft pulley securing bolt. 2. Insert the alignment tool supplied, so that it
is hooked in the crankshaft pulley teeth.
I
52. Remove the special tool.
53. Install the cylinder block lower blanking
plug9
54. N0TE:When installing a new crankshaft
pulley or engine front cover, the crankshaft
position
(CKP) sensor must be aligned
using the alignment tool supplied with the
new component.
N0TE:Do not tighten the bolts at this stage.
Align the CKP sensor.
1.
Loosen the CKP sensor retaining bolts.
55. Install the CKP sensor.
I. Tighten the CKP sensor retaining bolts.
2. Remove the alignment tool.
56. Install the coolant pump pulley.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

303-01 B-I11 Engine - 2.OL Duratec-HE (M14) 303-01 B-111
INSTALLATION
Engine
i Special Tool(s)
I
I Remover/lnstaller, Hose
General Equipment
I Workshop table 1
I Securing straps I
I Engine hoist I --
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable vapors are
always present and may ignite. Failure to
follow these instructions may result in
personal injury.
1. N0TE:Using suitable retaining straps, secure
the engine on the workshop table.
Support the engine with wooden blocks.
2. Install the transaxle.
3. Install the transaxle upper retaining bolts.
4. Install the transaxle left-hand retaining bolts.
5. Install the transaxle right-hand retaining
bolts.
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com

303-01 B-I 13 Engine - 2.OL Duratec-HE (M14) 303-01 B-113
INSTALLATION
12. Remove the securing straps. 17.
Attach the gearshift cables to the bracket
13. Raise and support the vehicle. For and
turn the abutment sleeves
( additional information, refer to: (I 00-02 counterclockwise.
Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
14. Install the engine support insulator.
15. Attach the air conditioning (NC)
compressor to the cylinder block. 18.
Attach the gearshift cables to the selector
levers.
19. CAUTIONS:
A~he inner CV joint must not be bent
more than 23 degrees. The outer CV joint
must not be bent more than 45 degrees.
16. Connect the
NC high pressure switch n~ake sure that the halfshaft seal is not
electrical connector. damaged.
n~ake sure the snap ring is correctly
seated.
N0TE:lnstall a new snap ring.
Using the special tool, attach the left-hand
halfshaft to the transaxle.
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com

Engine Cooling - I .3L DuratecdV
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
DESCRIPTION AND OPERATION
Components
Coolant pump
The coolant pump is secured to the engine block
at the timing gear end.
Item Description It is driven through a pulley b; the accessory drive
2006.0 Fiesta 1212006 GI 79022en
belt.
The gasket for the coolant pump must not be
reused. 1
2
I
Coolant pump
Coolant pump gasket
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)ll.4L
303-03A-21 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-03A-21
REMOVAL AND INSTALLATION
Water Pump - 1.25L Duratec-1 6V (Sigma)/l.4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V (Sigma)(24 404 0)
Removal
Vehicles built up to 0412005
Loosen the water pump pulley retaining
bolts.
1. Disconnect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air
cleaner.
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-12 Intake Air Distribution and
Filtering, Removal and Installation).
3. Drain the cooling system.
6. Lower the vehicle. For additional information, refer to: Cooling
System Draining, Filling and Bleeding - 1.3~ 7. Disconnect the degas hose from the coolant
Duratec-8V (Rocam)ll.25L Duratec-1 6V expansion tank.
(Sigma)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) (303-03 Engine
Cooling - 1.3L DuratecdV (Rocam)ll.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma), General
Procedures).
4. Remove the crankshaft
pulley splash shield.
5m AWARNING:D~ not remove the water pump
pulley retaining bolts at this stage as the
pulley is under tension from the accessory
drive
belt. Failure to follow this instruction
may
result in personal injury. 8.
Detach the
coolant expansion tank and
secure
it to one side.
2006.0 Fiesta 1212006 GI 89080en
procarmanuals.com