2007 FORD FIESTA key

206-0716 Power Brake Actuation 206-0716
DESCRIPTION AND OPERATION
Release of the brake assistant
Item Description
I I I ~ock sleeve I
1 3 IVacuum cylinder I
To release EBA, the brake pedal must be fully
released,
i.e. it must be returned to its rest position.
When this occurs, the control housing together with
the valve piston move back into the rest position.
The key is pressed against the stop on the vacuum
cylinder and by this the lock sleeve is slid back into
its rest position.
The balls can again be moved outward by the ball
sleeve, and the ball cage is again free to move
axially and the balls free to move radially.
Service
It is not possible to repair the EBA. A new brake
servo unit must be installed.
2006.0 Fiesta 12/2006 GI 63289en
procarmanuals.com

21 1 -02-25 Power Steering 21 1 -02-25
REMOVAL AND INSTALLATION
Remove the exhaust hanger insulator. 11. Remove the front axle crossmember
retaining bolts on both sides.
8. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
12. Lower the front axle crossmember
Detach the stabilizer bar link from the approximately
100 mm.
stabilizer bar on both sides.
13. Detach the steering gear to power steering
fluid reservoir return line from the power
steering pump to steering gear pressure
line.
9. Remove the engine support insulator.
10. Using a transmission jack and a wooden
block, support the front axle crossmember.
14' ~CAUTION:C~~ the steering gear valve
body inlet port and outlet port to prevent
fluid loss or dirt ingress.
Disconnect the power steering lines from the
steering gear valve body.
1. Remove the power steering lines clamp plate
retaining bolt.
2. Rotate the power steering lines clamp plate.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1-02-27 Power Steering 21 1 -02-27
REMOVAL AND INSTALLATION
Using the transmission jack, wooden block 7.
Install the front axle crossmember rear inner
and the special tool, position and align the retaining
bolts on both sides.
front axle crossmember.
8. Lower and remove the transmission jack and
5m &AUTION:W~~I~ tightening the front axle the
wooden block.
crossmember front retaining bolt and the
9. Install the engine support insulator.
front axle crossmem ber rear outer retaining
bolts, make sure that the front axle
crossmember does not move.
Install the front axle crossmember front
retaining bolt and the front axle
crossmember rear outer retaining bolts on
both sides.
i,
6. Remove the front axle crossmember rear
inner retaining bolts and the special tools.
10. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
Attach the stabilizer bar link to the stabilizer
bar on both sides.
~CAUTION:T~~~ care when installing the
exhaust hanger insulator to prevent
damage.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1 -02-33 Power Steering 21 1-02-33
REMOVAL AND INSTALLATION
Ifem 5 Cable ties Remove
the exhaust hanger insulator.
I I CAUTION:^^^^ bending of the exhaust
flexible pipe may cause damage resulting in
failure.
Support the exhaust flexible pipe with a
support wrap or splint.
*' n~A~T10~:Twistin~ the exhaust flexible
pipe more than two degrees may cause
damage resulting in failure.
, N0TE:Use a pry-bar to prevent the exhaust flexible
( , pipe from twisting when removing the catalytic
converter to muffler and tailpipe assembly retaining
nuts.
Remove the exhaust flexible pipe to catalytic
converter retaining nuts.
4. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
Detach the stabilizer bar link from the
stabilizer bar on both sides.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
5. Remove the engine support insulator.
3m ~CAUTION:T~~~ care when removing the 6. Using a transmission jack and a wooden
exhaust hanger insulator to prevent damage.
block, support the front axle crossmember.
2006.0 Fiesta 1212006 G458167en
procarmanuals.com

21 1 -02-36 Power Steering 21 1 -02-36
REMOVAL AND INSTALLATION
4. Remove the front axle crossmember rear Attach the stabilizer bar link to the stabilizer
inner retaining bolt and the special tool on
bar on both sides.
both sides.
9m &~uTl~~:Twistin~ the exhaust flexible 5. Install the front axle crossmember rear inner pipe more than two degrees may cause retaining bolts on both sides.
damage resulting in failure.
N0TE:Use a pry-bar to prevent the exhaust flexible
pipe from twisting when installing the exhaust
flexible pipe to catalytic converter retaining nuts.
N0TE:lnstall a new exhaust flexible pipe to
catalytic converter gasket and retaining nuts.
Install the exhaust flexible pipe to catalytic
converter retaining nuts.
6. Lower and remove the transmission jack and
wooden block.
7. Install the engine support insulator.
8. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
lo' ~CAUTION:T~~~ care when installing the
exhaust hanger insulator to prevent
damage.
N0TE:Check the exhaust hanger insulator for
damage. lnstall a new exhaust hanger insulator if
required.
2006.0 Fiesta 12/2006 G458167en
procarmanuals.com

2 1 1 -02-39 Power Steering 21 1-02-39
REMOVAL AND INSTALLATION
Support the exhaust flexible pipe with a Vehicles with diesel engine
support wrap or splint.
i 8. Detach the exhaust flexible pipe from the
muffler and tailpipe assembly.
&AUTION:T~~~ care when removing the
exhaust hanger insulator to prevent damage.
Discard the exhaust flexible pipe to muffler
and tail pipe assembly retaining nuts.
Remove the exhaust hanger insulator. Vehicles with 2.OL engine
9. Detach the exhaust flexible pipe from the
catalytic converter.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
Vehicles with 1.25L, 1.4L or 1.6L engine
7. Detach the exhaust flexible pipe from the
catalytic converter.
Discard the exhaust flexible pipe to catalytic
converter gasket and retaining nuts.
All vehicles
On &AUTION:L~~~~ the tie-rod end retaining
nuts in place to protect the ball joint studs.
N0TE:Use a 5 mm Allen key to prevent the ball
joint stud from rotating.
2006.0 Fiesta 1212006 GI 05648en
procarmanuals.com

21 1 -02-40 Power Steering 211=02-40
REMOVAL AND INSTALLATION
Loosen the tie-rod end retaining nut on both Detach the stabilizer bar connecting link from
sides. the stabilizer bar on both sides.
//
'Irn &AUTION:P~~~~~~ the ball joint seal 13.
Remove the engine support insulator.
using a soft cloth to prevent damage.
Using the special tool, detach the tie-rod end
from the wheel knuckle on both sides.
1 . Release the tie-rod end.
2. Remove and discard the tie-rod end retaining
nut.
12. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar connecting link ball joint stud
from rotating.
14. Detach the power steering line from the
steering gear (left-hand drive shown).
2006.0 Fiesta 1212006 GI 05648en
procarmanuals.com

211 -02-44 Power Steering 211 -02-44
REMOVAL AND INSTALLATION
Attach the exhaust flexible pipe to the muffler Check the exhaust hanger insulator for
and tailpipe assembly. damage. Install a new exhaust hanger
insulator
if required..
Vehicles with 1.25L, 1.4L or 1.6L engine
15. N0TE:Coat the exhaust flexible pipe studs 17' &AUTION:O~~~ bending of the exhaust
with grease.
flexible pipe may cause damage resulting
N0TE:lnstall a new exhaust flexible pipe to in failure.
catalytic converter gasket and retaining nuts. Remove the exhaust flexible pipe support
Attach the exhaust flexible pipe to the wrap
or splint.
catalytic converter.
*- AwARNING:~~~~~~~ new tie-rod end
All vehicles retaining nuts. Failure to follow this
instruction may result in personal injury.
16' AcAu~~oN:Take care when installing the NOTE:"se a 5 mm Allen key to prevent the tie-rod exhaust hanger insulator to prevent
damage. end ball joint stud from rotating.
2006.0 Fiesta iu2006 GI 05648en
procarmanuals.com